• Journal of Astronomy and Space Sciences
• /
• v.15 no.2
• /
• pp.401-415
• /
• 1998

This paper reports the results obtained from the Langmuir probe (LP) and Electron Temperature Probe (ETP) experiments on the sounding rocket KSR-II (Korean Scientific Rocket - II) which was launched on Jun 11, 1998 at 10:00 KST from Tae-An peninsula (37$^{\circ}$ N, 126$^{\circ}$ E). The instruments successfully measured the electron density, electron temperature, and the floating potential at altitudes of 73km to 130km. While the electron temperature measurement is not easy in this region, since the temperature is very low and the contamination effect of the probe may give rise to a problem, we were able to obtain a reasonable electron temperature profile by employing two independent methods, the pulse modulated Langmuir Probe and Electron Temperature Probe. The preliminary results show that electron density increases sharply at about 90km, and forms a peak at 102km. The density profile is roughly consistent with IRI (International Reference Ionosphere)95-model or PIM (Parameterized Ionospheric Model) results except that the peak density appears at 110km in the model and model electron density is slightly lower than the observed one. Electron temperature obtained from ETP fluctuates between 200$^{\circ}$K and 700$^{\circ}$K, an effect presumably coming from the wakes developed by LP, and it tends to increase with the altitude, which is consistent with the LP results.

• Journal of radiological science and technology
• /
• v.21 no.2
• /
• pp.36-42
• /
• 1998

Treatment of a large diseased area with electron often requires the use of two or more adjoining fields. In such cases, not only electron beam divergence and lateral scattering but also fields overlapping and separation may lead to significant dose inhomogeneities(${\pm}20%$) at the region of junction of fields. In this study, we made Acrylic Electron Wedges to improve dose inhomogeneities(${\pm}5%$) in these junction areas and to apply it to clinical practices. All measurements were made using 6, 9, 12, 16, 20 MeV Electron beams from a linear accelerator for a $10{\times}10\;cm$ field at 100cm of SSD. Adding a 1 mm sheet of acryl gradually from 1 mm to 15 mm acquires central axis depth dose beam profile and isodose curves in water phantom. As a result, for all energies, the practical range was reduced by approximately the same distance according to the acryl insert, e.g. a 1 mm thick acryl insert reduces the practical range by approximately 1 mm. For every mm thickness of acryl inserted, the beam energy was reduced to approximately 0.2 MeV. These effects were almost Independent of beam energy and field size. The use of Acrylic Electron Wedges produced a small increase(less than 3%) in the surface dose and a small increase(less than 1%) in X-ray contamination. For acryl inserts, thickness of 3 mm or greater, the penumbra width increased nearly linear for all energies and isodose curves near the beam edge were nearly parallel with the incident beam direction at the point of penumbra width($35\;mm{\sim}40\;mm$). We decide heel thickness and angle of the wedge at this point. These data provide the information necessary to design Acrylic Electron Wedge which can be used to improve dose uniformity at electron field junctions and it will be effectively applied to clinical practices.

• The Journal of Korean Society for Radiation Therapy
• /
• v.10 no.1
• /
• pp.60-68
• /
• 1998

Treatment of a large diseased area with electron often requires the use of two or more adjoining fields. In such cases, not only electron beam divergence and lateral scattering but also fields overlapping and separation may lead to significant dose inhomogeneities(${\pm}20\%$) at the field junction area. In this study, we made Acrylic Electron Wedges to improve dose homogeneities(${\pm}5\%$) in these junction areas and considered application it to clinical practices. All measurements were made using 6, 9, 12, 16, 20MeV Electron beams from a linear accelerator for a $10{\times}10cm$ field at 100cm SSD. Adding a 1 mm sheet of acryl gradually from 1 mm to 15 mm, We acquired central axis depth dose beam profile and isodose curves in water phantom. As a result, for all energies, the practical range was reduced by approximately the same distance as the thickness of the acryl insert, e.g. a 1 mm thick acryl insert reduce the practical range by approximately 1 mm. For every mm thickness of acryl inserted, the beam energy was reduced by approximately 0.2MeV. These effects were almost independent of beam energy and field size. The use of Acrylic Electron Wedges produced a small increase $(less\;than\;3\%)\;in\;the\;surface\;dose\;and\;a\;small\;Increase(less\;than\;1\%)$ in X-ray contamination. For acryl inserts, thickness of 3 mm or greater, the penumbra width increased nearly linear for all energies and isodose curves near the beam edge were nearly parallel with the incident beam direction, and penumbra width was $35\;mm{\sim}40\;mm$. We decide heel thickness and angle of the wedge at this point. These data provide the information necessary to design Acrylic Electron Wedge which can be use to improve dose uniformity at electron field junctions and it will be effectively applicated in clinical practices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.629-629
• /
• 2013

Graphene is a carbon based material and it has intriguing features, such as phenomenally strong, thin, flexible, transparent and conductive, those make it attractive for a broad range of applications.Unfortunately, graphene is extremely sensitive to contamination. When we fabricate graphene devices, electrical properties of graphene are altered [1], and the charge carrier mobility drops accordingly by orders of magnitude. This significant impact on electron mobility occurs because any surrounding medium could act as a dominant source of extrinsic scattering, which effectively reduces the mean free path of carriers [2,3]. The dominant contaminant is generated through fabrication stage by polymethyl methacrylate (PMMA) [4], or photo resist (PR). Surface contamination by these residues has long been a critical problem in probing graphene's intrinsic properties. If we clearly solve this problem, we can get highly performed graphene devices. Here, we will report on graphene cleaning process by Induced Coupled Plasma (ICP). We demonstrated how much decomposition of residue impact on improving electrical properties of graphene.

• The Korean Journal of Malacology
• /
• v.32 no.1
• /
• pp.45-54
• /
• 2016

To evaluate the applicability of cellular energy allocation (CEA) in the bivalves as a biomarker for the assessment of environmental contamination, the energy contents and energy consumption in several tissues of the Manila clam, Ruditapes philippinarum were analyzed. The contents of lipid, glucose, protein and electron transport system (ETS) activity in the foot, siphons, gills, and body of R. philippinarum exposed to crude oil-spiked sediments were measured at 1, 2, 4, 7, 10 days after exposure. The reserved energy (energy available, EA) in the lipid, glucose and protein decreased as contamination level and exposure time increased. In contrast, the ETS activity (energy consumed, EC) showed the reverse tendency. The order of available energy contents were foot > siphons > gill > body. Significant differences in both EA and EC were found only at the highest contamination level (58.3 mg TPAHs/kg DW). EA decreased significantly in the foot and gill at 1 day, in the body at 2 and 7 days after exposure. EC increased significantly in the body at 4 days after exposure. CEA showed higher sensitivity to the contamination than EA or EC. Especially, CEA in the foot and body decreased significantly at lower ranges of contamination level (as low as 6.5 mg TPAHs/kg DW) during 1 to 7 days after exposure. The CEA is more useful than EA or EC alone for the assessment of sediment contamination at lower level that acute toxicity could not be detected. CEA analyses in the body of R. philippinarum after 4 days' exposure to contaminated sediments seem to be the most sensitive and reliable.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.30-30
• /
• 2011

The wave-cutoff tool is a new diagnostic method to measure electron density and electron temperature. Most of the plasma diagnostic tools have the disadvantage that their application to processing plasma where toxic and reactive gases are used gives rise to many problems such as contamination, perturbation, precision of measurement, and so on. We can minimize these problems by using the wave-cutoff method. Here, we will present the results obtained through the development of the wave-cutoff diagnostic method. The frequency spectrum characteristics of the wave-cutoff probe will be obtained experimentally and analyzed through the microwave field simulation by using the CST-MW studio simulator. The plasma parameters are measured with the wave-cutoff method in various discharge conditions and its results will be compared with the results of Langmuir probe. Another disadvantage is that other diagnostic methods spend a long time (~ a few seconds) to measure plasma parameters. In this presentation, a fast measurement method will be also introduced. The wave-cutoff probe system consists of two antennas and a network analyzer. The network analyzer provides the transmission spectrum and the reflection spectrum by frequency sweeping. The plasma parameters such as electron density and electron temperature are obtained through these spectra. The frequency sweeping time, the time resolution of the wave-cutoff method, is about 1 second. A short pulse with a broad band spectrum of a few GHz is used with an oscilloscope to acquire the spectra data in a short time. The data acquisition time can be reduced with this method. Here, the plasma parameter measurement methods, Langmuir probe, pulsed wave-cutoff method and frequency sweeping wave-cutoff method, are compared. The measurement results are well matched. The real time resolution is less than 1 ?sec. The pulsed wave-cutoff technique is found to be very useful in the transient plasmas such as pulsed plasma and tokamak edge plasma.

• Biomedical Science Letters
• /
• v.10 no.3
• /
• pp.293-298
• /
• 2004

This study was performed to compare the growth rates, cellular fatty acid compositions and morphology by using electron microscope of Escherichia coli (E. coli) grown in various conditions including different concentrations of phenol, CdCl₂ and HgCl₂. Ninety eight E. coli strains were isolated from Naktong river and human feces. The content of unsaturated fatty acids, especially 16:1ω7c and 18:1ωc increased as the concentration of phenol and CdCl₂ increased. The content of unsaturated fatty acid increased up to 50 ppb of HgCl₂, but decreased at 75 ppb of HgCl₂. There were more unsaturated fatty acids than saturated fatty acid in the presence of toxic substances. However, the ration was reversed when the affected E. coli was transferred to toxic substance free fresh trypticase soy broth medium. Also, by using transmission electron microscope these cells were observed to various morphological deformation by heavy metals and their deposition on the surface. From these results, we suggested that the changes of major fatty acids composition and morphology of E. coli may be considered to indicate contaminated levels of heavy metals or organic solvents. The information presented here may be useful in predicting effects of heavy-metal and organic solvent contamination in streams and provides a basis for further studies of metal or organic solvent effects on microbial communities.

• Journal of Microbiology and Biotechnology
• /
• v.19 no.12
• /
• pp.1590-1595
• /
• 2009

Alternative methods for controlling bacterial endospore contamination are desired in a range of industries and applications. Attention has recently turned to natural products, such as essential oils, which have sporicidal activity. In this study, a selection of essential oils was investigated to identify those with activity against Bacillus subtilis spores. Spores were exposed to 13 essential oils, and surviving spores were enumerated. Cardamom, tea tree, and juniper leaf oils were the most effective, reducing the number of viable spores by 3 logs at concentrations above 1%. Sporicidal activity was enhanced at high temperatures ($60^{\circ}C$) or longer exposure times (up to 1 week). Gas chromatography-mass spectrometry analysis identified the components of the active essential oils. However, none of the major oil components exhibited equivalent activity to the whole oils. The fact that oil components, either alone or in combination, did not show the same level of sporicidal activity as the complete oils suggested that minor components may be involved, or that these act synergistically with major components. Scanning electron microscopy was used to examine spores after exposure to essential oils and suggested that leakage of spore contents was the likely mode of sporicidal action. Our data have shown that essential oils exert sporicidal activity and may be useful in applications where bacterial spore reduction is desired.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.12
• /
• pp.3535-3541
• /
• 2014

Bisphenol A is considered as pollutant, because it is toxic and hazardous to living organisms even at very low concentrations. Biological oxidation used for removing this organic from waste water is not suitable and consequently application of catalytic wet oxidation has been considered as one of the best options for treating bisphenol A. We have developed Fe/SBA-15, Ni/SBA-15 and Fe-Ni/SBA-15 as heterogeneous catalysts using the advanced impregnation method for oxidation of bisphenol A in water. The catalysts were characterized with physico-chemical characterization methods such as, powder X-ray diffraction (PXRD), FT-IR measurements, N2 adsorption-desorption isotherm, thermo-gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and inductively coupled plasma optical emission spectroscopy (ICP-OES) analysis. This work illustrates activity of the catalysts for heterogeneous catalytic degradation reaction revealed with excellent conversion and recyclability. The degradation products identified were not persistent pollutants. GC-MS analysis identified the products: 2,4-hexadienedioic acid, 2,4-pentadienic acid and isopropanol or acetic acid. The leachability study indicated that the catalysts release very little metals to water. Therefore, the possibility of water contamination through metal leaching was almost negligible.

• Journal of Food Hygiene and Safety
• /
• v.9 no.4
• /
• pp.191-198
• /
• 1994

The major purpose of the present study is to syrvey vegetables, meats, seafoods, processed foods and imported foods for the presence of Listeria spp. and to prevent listeriosis caused by the contamination of Listeria monocytogenes. Listeria spp. was not found in vegetables and processed foods. The optimum growth condition of isolates indentified as Listeria monocytogenes was pH 7.0 and 37$^{\circ}C$. the antimicrobial effect of grapefruit seed extract(GFSE) was observed in the level of more than 100ppm by disk method. When 1ml(2.5$\times$106 CFU/ml) of Listeria monocytogenes was inoculated and incubated for 3 days at 3$0^{\circ}C$, the total cell number of the organism was 4.5$\times$109 in the control, 7.2$\times$103 in 100 $\mu\textrm{g}$/ml of GFSE medium, and 3.5 $\mu\textrm{g}$/ml of GFSE medium. Direct visualization of microbial cells by using both transmission electron microscope and scanning electron microscope showed microbial cell membrane the function of which was destroyed by treating with the dilute solutions of GFSE. It could be confirmed that GFSE completely inhibited the growth of the test strain of Listeria monocytogenes.