• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.04a
• /
• pp.374-378
• /
• 2014

The piezoelectric materials convert from mechanical energy to electrical energy. The piezoelectric materials are used in various engineering applications such as piezoelectric ultrasonic actuators. Since the piezoelectric coupling characteristics of the actuator systems should be considered at the initial design stage, it is essential to analyze the piezoelectric coupling characteristics of the ultrasonic actuators. In this study, we analyzed the electromechanical characteristics of piezoelectric stacked actuator using the equivalent circuit model with modal mass stiffness parameters. It was compared the admittance of piezoelectric stack actuators with the analytical circuit model and the finite element model. Also, the coupling coefficient of piezoelectric stack actuator was discussed according to the number of stacks of actuators.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.375-378
• /
• 2011

A valve's high response for controlling thruster is essential for rapid turning during initial short moment after launching. The actuator for controlling the valve is simultaneously used in controlling canard of a guided missile. This paper explain development process for the electromechanical actuator interlocked with canard by arranging in following order, design, analysis, manufacture, test and evaluation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.219-220
• /
• 2006

In this study, m order to develop multilayer ceramics vibrator for ultrasonic nozzle, PMN-PNN-PZT ceramics were fabricated using $Li_2CO_3-Na_2CO_3$ as sintering aids and their piezoelectric and dielectric characteristics were investigated according to the aomunt of PbO. With increasing PbO contents. secondary phases were increased and phase structure were changed from tetragonal structure to rhombohedral structure and also electromechanical coupling factor were linearly decreased. At the composition ceramics with the sintering temperature of $870^{\circ}C$ and 1 mol% excess PbO, density, electromechanical coupling factor, dielectric constant, piezoelectric d constant and mechanical quality factor showed the optimum value of $7.879g/cm^2$, 0.55, 1149, 328pC/N, 1224, respectively for multilayer ceramics vibrator application for ultrasonic nozzle.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2006.05a
• /
• pp.570-573
• /
• 2006

It is proposed that the electromechanical relation of the conductive materials with high electrical resistance may be used to estimate the current stress of prestressing tendons. To choose the best conductive material to this end, we studied the electromechanical relations of carbon fibers and metalic heat wires experimentally. It is found that the relation of carbon fibers can be modelled by a parabolic(or hyperbolic) function in the early stage of deformation. Metallic heat wires show a consistent linear relation during loading and unloading in the elastic deformation and are suitable for this purpose. We propose a new kind of prestressing tendons whose stress can be monitored.

• Interaction and multiscale mechanics
• /
• v.2 no.4
• /
• pp.413-430
• /
• 2009

The stator tooth is a key component of the electromechanical integrated toroidal drive system. The stator tooth is spiral in shape and the calculation of its displacements is difficult. In this paper, using the coordinate transformation method, the displacements of the stator tooth in the local coordinate system are expressed as the function of the variable in the drive coordinate system. Using the minimum potential energy principle, the equations of the displacements of the stator tooth under the loads are deduced. The displacement distributions within the stator tooth are investigated and the changes of the displacement distributions along with the main parameters are analyzed. This research can offer the basis for the strength and stiffness design of the drive system.

• Structural Monitoring and Maintenance
• /
• v.1 no.2
• /
• pp.159-171
• /
• 2014

Real-time near and far-field monitoring of concrete structural components gives enough information on the time and condition at which damage occurs, thereby facilitating damage detection while in the same time evaluate the cause of the damage. This paper experimentally investigates an integrated monitoring technique for near and far-field damage detection in concrete structures based on simultaneous use of electromechanical admittance technique in combination with guided wave propagation. The proposed sensing system does not measure the electromechanical admittance itself but detect time variations in output voltages of the response signal obtained across the electrodes of piezoelectric transducers bonded on surfaces of concrete structures. The damage identification is based on the spectral estimation MUSIC algorithm. Experimental results show the efficiency and performance of the proposed measuring technique.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1179-1183
• /
• 2007

Electro-Active paper(EAPap) is a new smart material that has a potential to be used in biomimetic actuator and sensor. It is made by cellulose that is abundant material in nature. EAPap is fascinating with its biodegradability, lightweight, large displacement, high mechanical strength and low actuation voltage. Actuating mechanism of EAPap is known to be the combined effects of ion migration and piezoelectricity. However, the electromechanical actuation mechanisms are not yet to be established. This paper presents the modeling of the actuation behavior of water infused cellulose samples and their composite dielectric constants calculated by Maxwell-Wagner theory. Electro-mechanical forces were calculated using Maxwell stress tensor method. Bending deflection was evaluated from simple beam model and compared with experimental observation, and which result in good correlation with each other.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.9 no.9
• /
• pp.3655-3671
• /
• 2015

In this paper, we develop a novel object tracking method based on sparse representation. First, we propose a relaxed sparse representation model, based on which the tracking problem is casted as an inverse sparse representation process. In this process, the target template is able to be sparsely approximated by all candidate samples. Second, we present an objective function that combines the sparse representation process of different fragments, the relaxed representation scheme and a weight reference prior. Based on some propositions, the proposed objective function can be solved by using an iteration algorithm. In addition, we design a tracking framework based on the proposed representation model and a simple online update manner. Finally, numerous experiments are conducted on some challenging sequences to compare our tracking method with some state-of-the-art ones. Both qualitative and quantitative results demonstrate that the proposed tracking method performs better than other competing algorithms.

• International Journal of Aeronautical and Space Sciences
• /
• v.12 no.4
• /
• pp.371-378
• /
• 2011

In this paper, the wavelet denoising techniques using thresholding method are applied to the low cost micro electromechanical system (MEMS)-global positioning system(GPS) integrated system. This was done to improve the navigation performance. The low cost MEMS signals can be distorted with conventional pre-filtering method such as low-pass filtering method. However, wavelet denoising techniques using thresholding method do not distort the rapidly-changing signals. They can reduce the signal noise. This paper verified the improvement of the navigation performance compared to the conventional pre-filtering by simulation and experiment.

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.650-652
• /
• 2017

the aim of this study was to observe the combined effect of the CRT and LVAD on electromechanical cardiac behavior under LBBB and RBBB conditions computationally. We performed simulation by using advanced electromechanics model of failing ventricle combined with lumped model represents circulatory system, CRT and LVAD. We analyzed seven failing ventricle model including normal sinus rhythm, LBBB, LBBB coupled with CRT, LBBB coupled with CRT and LVAD, RBBB, RBBB coupled with CRT, and RBBB coupled with CRT and LVAD. We compared the effect from CRT and the effect from combined CRT and LVAD to both under LBBB and RBBB conditions. The results showed that the combined CRT and LVAD contributed a better hemodynamic compared to single CRT. This combined system synchronized the electrical activation greatly under LBBB and slightly under RBBB. It also shortened mechanical activation time which resulted short electromechanical delay. More importantly, the combined system produced better mechanical responses under both LBBB and RBBB conditions.