• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.840-846
• /
• 2011

In this paper, reflection and RCS characteristic of the EGS(Electromagnetic Gradient Surface) due to incident angle and polarization is analyzed. Incident angle, ${\theta}_i$, is rotated from $0^{\circ}$ to $50^{\circ}$ with $10^{\circ}$ steps and perpendicular and parallel polarization of incident wave are also considered each incident angle. Reflection and RCS characteristic is not much affected by variation of polarization for normal incidence(${\theta}_i=0^{\circ}$). Reflection pattern has different characteristic due to variation of incident angle and polarization but the EGS has about 2 dB of RCS difference due to polarization in RCS characteristic.

• Journal of Welding and Joining
• /
• v.17 no.6
• /
• pp.70-77
• /
• 1999

Surface depression in the arc welding is calculated numerically to analyze its influence on pool convection and oscillation. The magnitude of surface depression due to arc pressure on the stationary GTA pool surface is relatively small, and fluctuations of the surface and velocity are caused mainly by arc pressure. The inward flow on the surface due to the electromagnetic force and positive surface tension gradient acts to decrease surface depression. Surface depression appears to have minor effects on average flow velocity and thus pool geometry. Pool oscillation occurs due to surface vibration, and oscillation frequencies are affected mainly by the surface tension and pool width. The input parameters such as arc pressure and current have negligible effects on the oscillation frequency, and the surface tension gradient has limited effects. Since the oscillation frequency varies slightly according to penetration, pool oscillation for the partial penetration weld pool is applicable to monitor the pool width.

• Journal of Magnetics
• /
• v.5 no.2
• /
• pp.59-64
• /
• 2000

A drum type of high gradient magnetic separator was designed and optimized by computer simulations. The magnetic separator consists of high performance rare earth $(Nd_2Fe_14B)$ permanent magnets and magnetic yokes of extremely low carbon steel interconnecting the permanent magnets. Magnetic circuits of the separator were simulated for the aim of the least cost, highest magnetic strength and most efficient function by using specialized S/W (Vector Field Program) employing the Finite Element Method. The magnetic flux density was provided to be strong enough to collect the invisible fine metal particles from the surface of hot rolled steel plate with the efficiency of almost 95%.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.10
• /
• pp.1254-1264
• /
• 1999

A three-dimensional coupled turbulent fluid flow and solidification process were analyzed in a continuous casting process of a steel slab with Electromagnetic Brake(EMBR). A revised low-Reynolds number $k-{\varepsilon}$ turbulence model was used to consider the turbulent effects. The enthalpy-porosity relation was employed to suppress the velocity within a mushy region. The electromagnetic field was described by Maxwell equations. Tile application of EMBR to the mold region results in the decrease of the transfer of superheat to the narrow face, the increase of temperature in free surface region and most liquid of submold region, and the higher temperature gradient near the solidifying shell. The increasing magnetic flux density effects mainly to the surface temperature of the solidifying shell of narrow face, hardly to the one of wide face. It is seen that in the presence of EMBR a thicker solidifying shell is obtained at the narrow face of the slab.

• Journal of IKEEE
• /
• v.16 no.4
• /
• pp.328-334
• /
• 2012

In this paper, we analyzed the electromagnetic characteristics of the spherical frequency selective surface with different arrangement of crossed dipole slot elements for reducing the RCS(radar cross section). The three dimensional MOM(method of moment) with RWG basis is used to analyze the proposed structure. To reduce the simulation time, we applied the BiCGSTab(Biconjugate Gradient Stabilized) algorithm as an iterative method and presented the comparison results with Mie's theoretical results for PEC sphere to show the validity of this paper. From the simulation results, the different arrangement of elements array showed the difference RCS that cannot be negligible. The arrangement method of element in frequency selective surface will be one of variables for the design of curved frequency selective structures.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.7
• /
• pp.831-839
• /
• 2012

In this paper, an exponential model of Korea is proposed to minimize an altitude-error of high-altitude target due to atmosphere refraction at radar system. The relation between surface refractivity and refractivity gradient, which is extracted using the least square fit from the measured data at 7 weather stations, is applied to the exponential model. And in order to verify the proposed model, the altitude-errors for a standard atmosphere, a CRPL(Central Radio Propagation Lab.) exponential model, the proposed model are extracted and analyzed using a ray tracing. As a result, the proposed model can improve the altitude estimation performance of radar compared to conventional atmosphere refractive index models.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.2
• /
• pp.59-64
• /
• 2001

The distribution of current in the conductors influenced by the armature geometry and velocity is an important parameter for determining performance of an electromagnetic launcher(EML). the electric current in the early launching stage tends to flow on the outer surfaces of the conductors, resulting in very high local electric current density. However, the tendency for current to concentrate on the surface is driven by the velocity skin effect later in launching stage. The high current density produces high local heating and, consequently, increases armature wear which causes several defects on EML system. This paper investigates the effects of rail/armature geometry on current density distribution, launcher inductance gradient (L'), and contact force. Three geometrical parameters are used here to characterize the railgun system. These are the ratio of contact length to root length, relative position of contact leading edge to root trailing edge, and the ratio of rail overhang to the rail height. The distribution of current density, L', contact force between various configurations of the armature and the rail are analyzed and compared by using the EMAP3D program.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.757-762
• /
• 2002

Many reports have been shown that the buoyancy, electromagnetic force, surface tension, and gas shear stress are the driving forces of weld pool circulation in arc welding. Among them, the surface tension of molten metal plays an important role in the flow in weld pool, which are clarified by the specially designed experiments with small particles as well as the numerical simulations. The surface tension is also related to the penetration in arc welding. Therefore, a quantitative evaluation of surface tension is demanded for the development of materials and arc process control. However, there are few available data published on the surface tension of molten metals, since it depends on the temperature and the composition of materials. In this study, a new method was proposed for the evaluation of surface tension and its temperature dependence, in which it is evaluated by the equilibrium condition of acting forces under a given surface geometry, especially back surface. When this method was applied to the water pool and to the back surface of molten pool in the stationary gas tungsten arc welding of thin plate, following results were obtained. In the evaluation of surface tension of water, it was shown that the back surface geometry was very sensitive to the evaluation of surface tension and the evaluated value coincided with the surface tension of water. In the measurement of molten pool in the stationary gas tungsten arc welding, it was also shown that the comparison between the surface tension and temperature distribution across the back surface gave the temperature dependent surface tension. Applying this method to the mild steel and stainless steel plates, the surface tension with negative gradient for temperature is obtained. The evaluated values are well matched with ones in the published papers.

• Composites Research
• /
• v.23 no.2
• /
• pp.24-30
• /
• 2010

Interfacial evaluation and hydrophobicity of Ni-nanopowder/epoxy composites were investigated for self-sensing and actuation. Contact resistance and resistivity were measured using gradient micro-specimens. The actuation of the composites in the electromagnetic field was studied with three wave functions, i.e., sine, triangle and square functions. Due tothe presence of hydrophobic domains on the heterogeneous surface, the static contact angle of Ni-nanopowder/epoxy nanocomposite wasabout $100^{\circ}$, which was rather lower than that for super-hydrophobicity. The dynamic contact angle showed the similar trend of static contact angle. Ni-nanopowder/epoxy composite was responded wellfor both self-sensing and actuation in electromagnetic field due to the intrinsic metal property of Ni-nanopowder. Displacement of the actuator of Ni-nanopowder/epoxy composite was evaluated to obtain the maximum and the optimum performance using laser displacement sensor as functions of the wave type, frequency, and voltage. Actuation of Ni-nanopowder/epoxy composites also increased as functions of applied frequency and voltage. Actuated strain increased more rapidly at sine wave with increasing voltage compared to those of triangle or rectangular waves.