• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2006.10a
• /
• pp.89-89
• /
• 2006

• Journal of the Korean institute of surface engineering
• /
• v.22 no.4
• /
• pp.207-214
• /
• 1989

The surface morphology and the proferred orientation of the Pb-Sn alloy electrodeposite were investated by the change of electrolysis conditions in pulse current electroplating. The preferred orientation of Pb-phase in alloy deposits was changed in the sequence of (110)longrightarrow(100)or(100)+(111)longrightarrow(111) with increasing peak current density, while that of $\beta$-Sn phase changed from (321)+(301)to(301)+(111) mixed orientation. The surface morphology was closely related to the preferred orientation of alloy electrodeposits. The alloy deposits, which had (100)or(111) for pb-phase and (321)or(100)(301)for $\beta$-Sn sespectively, showed the surface structure of granular crystallites. The alloy deposits whih mixed orientations for both phases had microstructure of closely the closely stacked crysrallites, which was inclined to the surface.

• Journal of the Korean institute of surface engineering
• /
• v.42 no.5
• /
• pp.191-196
• /
• 2009

Nanocrystalline Cu thin films were electrodeposited from sulfate baths and investigated systematically the influences of $Cu^{2+}$ concentration and additives on current efficiency, residual stress, surface morphology, and XRD patterns of electrodeposited Cu film. Current efficiency was nearly 100% at from 0.2M to 1.0 M $Cu^{2+}$ concentration. but it was linearly increased with $Cu^{2+}$ concentration at less than 0.2M. The residual stress was observed in range of 7.9 to 18.4 MPa and tensile stress mode. Dendritic and powdered form was obtained at below 0.1 M. As increased with $Cu^{2+}$ concentration in solution, the main peak in the XRD pattern shifted (111) and (220) from (200). In the other hand, all about 100% current efficiency observed in all additive concentration systems, and residual stress observed in range of 20.4 to 26.3 MPa tensile stress. The condition 5(Ultra make-up - 10 ml/l, Ulta A - 0.5ml/l, Ultr B - 0.5 ml/l) was good surface morphology, and fcc(111) peak in XRD patterns increased with increasing additive concentration.

• Journal of the Korean Electrochemical Society
• /
• v.13 no.2
• /
• pp.132-137
• /
• 2010

This study is concerned the electrocatalytic generation of oxygen gas at electrochemically deposited manganese oxide electrode in KOH solution. Manganese oxide nanoparticles electrodeposited onto relatively substrate, e.g glassy carbon, Au, Ti electrode. MnOx is electrodeposited in nanorod structure which cover the overall surface of the substrate. The $\gamma$-MnOOH that is kind of manganese oxide species plays a significant role as a catalytic mediator, which promote 4-electron reduction process. Modified electrodes with electrodeposited manganese oxide structures resulted in significant decrease in the anodic polarization compared with the unmodified electrodes in alkaline media.

• Journal of Electrochemical Science and Technology
• /
• v.2 no.3
• /
• pp.168-173
• /
• 2011

The availability, low toxicity, and high degree of technological development make silicon the most likely material to be used in solar cells, the cost of solar cells depends entirely on cost of high purity silicon production. The present work was conducted to electrodeposite of silicon from $K_2SiF_6$, an inexpensive raw material prepared from fluorosilicic acid ($H_2SiF_6$) produced in Iraqi Fertilizer plants, and using inexpensive graphite material as cathode electrode. The preparation of potassium fluorosilicate was performed at ($60^{\circ}C$) in a three necks flask provided with a stirrer, while the electro deposition was performed at $750^{\circ}C$ in a three-electrodes configuration with melt containing in graphite pot. High purity potassium fluorosilicate (99.25%) was obtained at temperature ($60^{\circ}C$), molar ratio-KCl/$H_2SiF_6$(1.4) and agitation (600 rpm). Spongy compact deposits were obtained for silicon with purity not less than (99.97%) at cathode potential (-0.8 V vs. Pt), $K_2SiF_6$ concentration (14% mole percent) with grain size (130 ${\mu}m$) and level of impurities (Cu, Fe and Ni) less than (0.02%).

• Korean Journal of Metals and Materials
• /
• v.50 no.3
• /
• pp.237-242
• /
• 2012

The objective of this study is to investigate the effect of additives on the mechanical and electrical characteristics of electrodeposited copper foils. Additives A(leveler) and B(brightener) were used in this study and Cl ions were used as an accelerator. In case of using these additives A and B, it showed a disadvantage that decreased the elongation of electrodeposited layer due to decreased grain sizes and increased tensile strength. On the other hand, the Cl ions decreased the specific resistance of the copper layer and increased elongation owing to increasing grain sizes. The highest elongation and lowest resistivity were measured in the group added only Cl ions, whose values were 21.9% and $3.11{\mu}\Omega$-cm, respectively.

• Applied Chemistry for Engineering
• /
• v.7 no.2
• /
• pp.280-288
• /
• 1996

In the ozone evolution using $PbO_2$, which was electrodeposited on Ti plate at various conditions in electrolyte, the effects of lead dioxide structure on the current efficiency and surface structure changes of lead dioxide were investigated. Also the effects of oxygen transfer reaction on the ozone evolution were investigated by means of a $PbO_2$ electrodeposited on the platinum rotating disk electrode. In order to develope an electrode for ozone evolution, durability of lead dioxide and optimum current density were investigated. At the electrodeposited lead dioxide with the larger grain size and higher crystallinity, the efficiency for ozone evolution was higher. Optimum current density to electrodeposite lead dioxide with large grain size and high crystalinity was $50mA/cm^2$. Lead dioxide deposited in the presence of glycerin showed the best advantage of ozone evolution. Also lead dioxide electrodeposited at less than $10mA/cm^2$ or at more than $100mA/cm^2$ has poor performance of ozone evolution and poor adhesive strength to substrate. In the beginning of ozone evolution, surface structure of lead dioxide was changed and this change resulted in good effects on ozone evolution. Lead dioxide doped with other elements was favorable not to ozone evolution but to oxygen evolution, so it is speculated that ozone evolution has not intermediate stage of oxygen evolution and occurs competitively with oxygen evolution. When ozone was evolved at $0.7{\sim}0.8A/cm^2$, the current efficiency was highest.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.1
• /
• pp.26-34
• /
• 2010

The electrocatalystic prperties of Pt-Co and Pt-Ni with heteropolyacids (HPAs) entrapped in covalently cross-linked sulfonated poly(ether ether ketone) (CL-SPEEK)/HPA membranes were investigated for water electrolysis. The HP As, including molybdophosphoric acid (MoPA), and tungstophosphoric acid (TPA) were both used as membrane additives and electrocatalysts. The membrane electrode assembly (MEA) was prepared by a nonequilibrium impregnation-reduction (I-R) method. $Pt(NH_3)_4Cl_2$, $NiCl_2$ and $CoCl_2$ as electrocatalytic materials and $NaBH_4$ as reducing agent were used. I order to enhance electrocatalytic activity, the catalyst layer prepared above was electrodeposited (Dep) with HP A. Surface morphologies and physico-chemical properties of MEA were investigated by means of SEM, EDX and XRD. The electrocatalytic properties of composite membranes such as the cell voltage and coulombic charge in CV were in the order of magnitude: CL-SPEEK/MoPA40 (wt%) > CL-SPEEK/TPA30 > Nafion117. In the optimum cell applications for water electrolysis, the cell voltage of Pt/CL-SPEEK-MoPA40/Pt-Co (Dep-MoPA) and Pt/CL-SPEEK-TPA30/Pt-Co (Dep-TPA) was 1.75 Vat $80^{\circ}C$ and $1\;A/cm^2$ and voltage efficiency was 87.1%. Also, the observed activity of Pt-Co (84:16 atomic ratio by EDX) is a little higher than that of Pt-Ni (86: 14). The current density peak of electrodeposited electrodes were better a little than those of unactivated electrodes based on the same membranes.