• Journal of Korean Vacuum Science & Technology
• /
• 제3권1호
• /
• pp.90-94
• /
• 1999

Field Emission display (FEDs) require enhancement in both driving methods and process techniques to improve the display image quality. However, from the point of view of manufacturing, it is difficult to find methods and techniques to realize low cost manufacturing. New and simple color phosphor screen designs were suggested with non-crossed electrode lines and full color anode panels for small area displays were demonstrated. To avoid unwanted reaction with gases produced from phosphors in a high vacuum glass container, a very thin polyimide layer was coated on the phosphor screen. Moreover, to improve the display image quality, black matrix composed of inorganic materials was fabricated. This paper describes the performance and characteristics of the new full color anode panels.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권12호
• /
• pp.639-647
• /
• 2001

We present an integrated optical microswitch, composed of silicon waveguides, gold-coaled silicon micromirrors, and electrostatic contact actuators, for applications to the optical signal transceivers. For a low switching voltage, we modify the conventional curled electrode microactuator into a electrostatic microactuator with touch-down beams. We fabricate the silicon waveguides and the electrostatically actuated micromirrors using the ICP etching process of SOI wafers. We observe the single mode wave propagation through the silicon waveguide with the measured micromirror loss of $4.18\pm0.25dB$. We analyze major source of the micromirror loss, thereby presenting guidelines for low-loss micromirror designs. From the fabricated microswitch, we measure the switching voltage of 31.74V at the resonant frequency of 6.89kHz. Compared to the conventional microactuator, the present contact microactuator achieves 77.4% reduction of the switching voltage. We also discuss a feasible method to reduce the switching voltage to 10V level by using the electrode insulation layers having the residual stress less than 30MPa.

• 한국수소및신에너지학회논문집
• /
• 제23권1호
• /
• pp.8-18
• /
• 2012

This paper presents a three-dimensional, transient cold-start polymer electrolyte fuel cell (PEFC) model to numerically evaluate the effects of membrane electrode assembly (MEA) design and cell location in a PEFC stack on PEFC cold start behaviors. The cold-start simulations show that the end cell experiences significant heat loss to the sub-freezing ambient and thus finally cold-start failure due to considerable ice filling in the cathode catalyst layer. On the other hand, the middle cells in the stack successfully start from $-30^{\circ}C$ sub-freezing temperature due to rapid cell temperature rise owing to the efficient use of waste heat generated during the cold-start. In addition, the simulation results clearly indicate that the cathode catalyst layer (CL) composition and thickness have an substantial influence on PEFC cold-start behaviors while membrane thickness has limited effect mainly due to inefficient water absorption and transport capability at subzero temperatures.

• 대한기계학회논문집B
• /
• 제31권10호
• /
• pp.832-839
• /
• 2007

The geometry and dimensions of an expansion chamber are decisive factors in thermal puffer plasma chamber designs. Because they together dominate the temperature and speed at which the cooling gas from the chamber flows back through a flow channel to the arcing zone for the successful interruption of fault currents. In this study, we calculated the flow and mass transfer driven by arc plasma, and investigated the effects of a flow guide installed inside a thermal puffer plasma chamber. It is found that the existing cold gas of the chamber mixes with hot gases entrained from the arcing zone and is subjected to compression due to pressure build-up in the chamber. The pressure build-up with the flow guide is larger than that without due to a vortex which rotates clockwise around the chamber center. By the reverse pressure gradient, the mixing gas of the chamber flows back out for cooling down the residual plasma near current zero. In the case with the flow guide, the temperature just before current zero is lower than that without, and the Cu concentration with high electrical conductivity is also less than that without the flow guide.

• 한국항공우주학회지
• /
• 제39권6호
• /
• pp.517-525
• /
• 2011

차분 진동형 가속도계는 입력 가속도에 따른 공진 주파수의 변화를 감지하는 공진형 센서이다. 이 때 가속도계 전기적 동역학의 수학적 모델링 및 구조 특성의 실험적 검증이 정밀한 제어기 및 높은 양질계수를 가지는 구조 설계에 앞서 필요하게 된다. 본 논문에서는 차분 진동형 가속도계의 공진자, 전극 모듈 및 전치증폭기 등의 전기적 모델링을 제시한다. 이러한 모델링 기법은 공진 주파수, 유효 질량, 유효 강성, 양질 계수 등을 측정함으로써 실험적으로 검증된다. 또한 모델링을 통해 예측된 진폭과 측정된 전치증폭기 출력의 직접적인 비교는 본 연구의 유효성을 보여준다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.480-480
• /
• 2008

Vacuum circuit breaker(VCB) is now emerging as an alternative of gas circuit breaker(GCB) which uses SF6 gas as insulating material whose dielectric strength is outstanding. But we have to reduce SF6 gas because SF6 gas is one of greenhouse gas and efforts to reduce greenhouse gas are now trend of the world. Therefore, we can say VCB is the optimal alternative of GCB because vacuum is environmentally friendly. The vacuum interrupter is the core part of VCB to interrupt arcing current. There are mainly two methods to extinguish arc. One is radial magnetic field (RMF) method and the other is axial magnetic field (AMF) method. We deals with RMF method in this paper. Compared with AMP, RMF arc quenching method has different principle to extinguish arc. In case of RMF method, pinch effect is much larger than AMF method. Because of pinch effect RMF type contact electrodes have the single large spot which is severly damaged and melted while AMF type contact electrodes have small and multiple spots which are slightly damaged and melted. To prevent contact electrode being damaged and melted from high temperature-arc, RMF method uses Lorentz force to move arc. In this paper we calculated and compared the arc driving force of two cases and we analyzed the force acting on each part of arc by means of commercial finite element method software Maxwell 3D. They have 3petals and we considered two cases. One is the case when fixed(upper) and movable(lower) contacts are in mirror arrangement (Case 1). The other is the case when one of two contacts (movable contact) is revolved at maximum angle as possible as it can be (Case 2). And at each case above, we analyzed arc driving force at two positions, position 1 is the closest to the center of contact and position 2 is near the edge of petal on fixed contact. As a result we could find that Case 2 generated stronger arc driving force than Case 1 at position 1. But at position 2 Case 1 generated stronger arc driving force than Case 2. This simulation method can contribute to optimizing spiral-type electrode designs in a view of arc driving force.

• 감성과학
• /
• 제24권2호
• /
• pp.49-56
• /
• 2021

본 연구의 목적은 생체 신호 측정 압력 및 인장 직물 센서의 전극을 자수 공정을 이용하여 제작할 때 전도사의 필요 물성을 파악하는 것이다. 스마트 웨어러블 제품의 전극을 전도사를 이용한 자수 공정을 통해 전극 및 회로 등을 제작하면 불필요한 재료 손실이 없고 복잡한 전극 모양이나 회로 디자인을 컴퓨터 자수기를 이용하여 추가 공정 없이 제작할 수 있다. 하지만 보통의 전도사는 자수 공정 내의 부하를 못 이기고 사절 현상이 발생하기에 본 연구에서는 silver coated multifilament yarn 3종류의 기계적 물성인 S-S curve, 두께, 꼬임 구조 등을 분석하고 동시에 자수기의 실의 부하를 측정하여 자수 공정 내 전도사의 필요 물성을 분석하였다. 실제 샘플 제작에서 S-S curve의 측정 결과가 가장 낮은 silver coated polyamide/polyester가 아닌 silver coated multifilament의 사절이 발생하였으며 그 차이는 실의 꼬임 구조와 사절이 일어난 부분을 관찰한 결과 수직으로 반복적인 부하가 일어나는 자수 공정에서 꼬임이 풀리면서 사절이 일어나는 것을 알 수 있었다. 추가적으로 압저항 압력/인장 센서를 제작하여 생체 신호 측정용 지표인 gauge factor를 측정하였으며 스마트 웨어러블 제품의 대량 생산화에 중요한 부분인 자수 전극 제작으로의 적용 가능성을 확인하였다.

• 한국물환경학회지
• /
• 제26권4호
• /
• pp.681-686
• /
• 2010

Two different MFC designs were evaluated in batch mode: single compartment combined membrane-electrodes (SCME) design and twin-compartment brush-type anode electrodes (TBE) design (single chamber with two air cathodes and brush anodes at each side of the reactor). In SCME MFC, carbon anode and cathode electrodes were assembled with a proton exchange membrane (PEM). TBE MFC was consisted of brush-type anode and carbon cloth cathode electrodes without the PEM. A brush-type anode was fabricated with carbon fibers and was placed close to the cathode electrode to reduce the internal resistance. Substrates used in this study were glucose, leachate from cattle manure, or sucrose at different concentrations with phosphate buffer solution (PBS) of 200 mM to increase the conductivity thereby reduce the internal resistance. Hydrogen generating bacteria (HGB) were only inoculated in TBE MFC. The peak power densities ($P_{peak}$) produced from the SCME systems fed with glucose and leachate were 18.8 and $28.7mW/m^2$ at external loads of 1000 ohms, respectively. And the $P_{peak}$ produced from TBE MFC were 40.1 and $18.3mW/m^2$ at sucrose concentration of 5 g/L and external loads of 470 ohms, with a mediator (2-hydroxy-1, 4-naphthoquinone) and without the mediator, respectively. The maximum power density ($P_{max}$) produced from mediator present TBE MFC was $115.3mW/m^2$ at 47 ohms of an external resistor.

• 전기학회논문지
• /
• 제67권1호
• /
• pp.68-74
• /
• 2018

All transparent UV photodetector based on ZnO was fabricated with structure of NiO/ZnO/$SnO_2$/ITO by using RF and DC magnetron sputtering system. ZnO was deposited with 4 inch ZnO target (purity 99.99%) for a quality film. In order to build p-n junction up, p-type NiO was formed on n-type ZnO by using reactive sputtering method. The indium tin oxide (ITO) which is transparent conducting oxide (TCO) was applied as a transparent electrode for transporting electrons. To improve the UV photodetector performance, a functional $SnO_2$ layer was selected as an electron transporting and hole blocking layer, which actively controls the carrier movement, between ZnO and ITO. The photodetector (NiO/ZnO/$SnO_2$/ITO) shows transmittance over 50% as similar as the transmittance of a general device (NiO/ZnO/ITO) due to the high transmittance of $SnO_2$ for broad wavelengths. The functional $SnO_2$ layer for band alignment effectively enhances the photo-current to be $15{\mu}A{\cdot}cm^{-2}$ (from $7{\mu}A{\cdot}cm^{-2}$ of without $SnO_2$) with the quick photo-responses of rise time (0.83 ms) and fall time (15.14 ms). We demonstrated the all transparent UV photodetector based on ZnO and suggest the route for effective designs to enhance performance for transparent photoelectric applications.

• International Journal of Precision Engineering and Manufacturing
• /
• 제9권1호
• /
• pp.39-46
• /
• 2008

The end plates of fuel cell assemblies are used to fasten the inner stacks, reduce the contact pressure, and provide a seal between Membrane-Electrode Assemblies (MEAs). They therefore require sufficient mechanical strength to withstand the tightening pressure, light weight to obtain high energy densities, and stable chemical/electrochemical properties, as well as provide electrical insulation. The design criteria for end plates can be divided into three parts: the material, connecting method, and shape. In the past, end plates were made from metals such as aluminum, titanium, and stainless steel alloys, but due to corrosion problems, thermal losses, and their excessive weight, alternative materials such as plastics have been considered. Composite materials consisting of combinations of two or more materials have also been proposed for end plates to enhance their mechanical strength. Tie-rods have been traditionally used to connect end plates, but since the number of connecting parts has increased, resulting in assembly difficulties, new types of connectors have been contemplated. Ideas such as adding reinforcement or flat plates, or using bands or boxes to replace tie-rods have been proposed. Typical end plates are rectangular or cylindrical solid plates. To minimize the weight and provide a uniform pressure distribution, new concepts such as ribbed-, bomb-, or bow-shaped plates have been considered. Even though end plates were not an issue in fuel cell system designs in the past, they now provide a great challenge for designers. Changes in the materials, connecting methods, and shapes of an end plate allow us to achieve lighter, stronger end plates, resulting in more efficient fuel cell systems.