• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1632-1633
• /
• 2011

In IEC 62305-1 standard, the simple circuit consisting of RLC is used in order to form the fast rise time of 0.25/100 ${\mu}s$. But this circuit is very expensive system because the system is needed very high charging voltage up to 3.5 MV. In this paper, we suggest the generator which generates the current up to 10 kA by using the low charging voltage of the dozen kV. Therefore the generator was installed then we compared measure results with calculated results.

• Proceedings of the KIEE Conference
• /
• 2003.10a
• /
• pp.95-97
• /
• 2003

This paper describes electrical properties such as electrical conduction characteristics and space charge distributions of polyaniline/polystyrene conducting blends. It is interesting to note that the charging current decreased as the temperature was elevated when DC voltage was applied, and also the hopping distance decreased with the increase of temperature for the PANI/HIPS blends, while generally, the hopping distance decreases as the charging current increases. It is exposed that this result is opposed to widely known phenomenon. It could be examined viewing space charge distributions by a pulsed electroacoustic (PEA) method.

• Journal of Electrical Engineering and Technology
• /
• v.8 no.6
• /
• pp.1276-1282
• /
• 2013

This paper proposes a stochastic modeling of plug-in electric vehicles (PEVs) distribution in power systems, and analyzes the corresponding clustering characteristic. It is essential for power utilities to estimate the PEV charging demand as the penetration level of PEV is expected to increase rapidly in the near future. Although the distribution of PEVs in power systems is the primary factor for estimating the PEV charging demand, the data currently available are statistics related to fuel-driven vehicles and to existing electric demands in power systems. In this paper, we calculate the number of households using electricity at individual ending buses of a power system based on the electric demands. Then, we estimate the number of PEVs per household using the probability density function of PEVs derived from the given statistics about fuel-driven vehicles. Finally, we present the clustering characteristic of the PEV distribution via case studies employing the test systems.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.2305-2306
• /
• 2008

Charging of spacecraft occurs in plasma and radiation environment. Especially, we focused on an accident caused by internal charging in a glass material that was used as the cover plate of solar panel array, and tried to measure the charge distribution in glass materials under electron beam irradiation by using a PEA (Pulsed Electro-Acoustic method) system. In the case of a quartz glass (pure $SiO_2$), no charge accumulation was observed either during or after the electron beam irradiation. On the contrary, positive charge accumulation was observed in glass samples containing metal-oxide components. It is found that the polarity of the observed charges depends on the contents of the impurities. To identify which impurity dominates the polarity of the accumulated charge, we measured charge distributions in several glass materials containing various metal-oxide components and calculated the trap energy depths from the charge decay characteristics of all glass samples.

• Transactions on Electrical and Electronic Materials
• /
• v.3 no.4
• /
• pp.1-4
• /
• 2002

As the application of semiconductor chips into electronics increases, it requires more complete integration, which results in higher performance. And it needs minimization in device design for cost saving of manufacture. Therefore oxide gap fill has become one of the major issues in sub-micron devices. Currently HDP (High-Density Plasma) CVD system is widely used in IMD (Inter Metal Dielectric) to fill narrower space between metal lines. However, HDP-CVD system has some potential problems such as plasma charging damage, metal damage and etc. Therefore, we will introduce about one of via resistance failure by metal damage and a preventive method in this paper.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.8
• /
• pp.55-62
• /
• 2015

This paper deals with a switching method to minimize the current ripple component of 3-phase interleaved bidirectional DC-DC converter for charging and discharging of the battery. The characteristics of the output current ripple in 3-phase and 2-phase operation modes according to the variation of battery voltage is analyzed and a phase conversion method for minimizing the magnitude of the current ripple is proposed. The proposed method can extend the light load range because the switching frequency is lower than that of a 3-phase operating system. Simulation and experimental results show the usefulness of the proposed method.

• Journal of the Korean Society of Safety
• /
• v.9 no.4
• /
• pp.132-136
• /
• 1994

The new spray system is proposed by using a pipe with hygroscopic needle electrode In order to develop an air-cleaning ESP with high collection efficiency for submicron particles and high removal efficiency for NOx, SO$_2$, NH$_3$. Fundamental characteristics of charging water spray, which is not an usual wet type, are investigated experimentally. As a result, corona discharging mode and ozone generation rate are significantly affected by the operational conditions, such as the applied voltage and wet condition of the needle electrode.

• Journal of Advanced Navigation Technology
• /
• v.21 no.6
• /
• pp.620-625
• /
• 2017

Recently, the solar module for charging internet devices is installed in crowded areas to offers services so that people can charge their smartphones or tablets. But this charging module can not be linked with the information related to a bus approach so people are subject to let their belongings such as smartphone, tablet pc at the bus stop while they are still charging it. This paper proposes a system to inform the smart phone when the bus is accessed by using the LPWA technology and BLE technology to resolve such under-failures. This experimental result showed that the power usage of LPWA based bus entry systems is an average of X, confirming that the long period usage of low-power can be possible for low power consumption in this results, enabling information on the bus to be transmitted to smart phones using Advertising mode of BLE.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.3
• /
• pp.566-571
• /
• 2011

As Plug-in Hybrid Vehicle and Electric Vehicle (PHEV/EV) take a greater share in the personal automobile market, their high penetration levels may bring potential challenges to electric utility especially at the distribution level. Thus, there is a need for the flexible charging management strategy to compromise the benefits of both PHEV/EV owners and power grid side. There are many different management methods that depend on the objective function and the constraints caused by the system. In this paper, the schema and dispatching schedule of centralized PHEV/EV charging spot network are analyzed. Also, we proposed and compared three power allocation strategies for centralized charging spot. The first strategy aims to maximize state of vehicles at plug-out time, the rest methods are equalized allocation and prioritized allocation based on vehicles SoC. The simulation results show that each run of the optimized algorithms can produce the satisfactory solutions to response properly the requirement from PHEV/EV customers.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.59 no.4
• /
• pp.456-461
• /
• 2010

This study compares the criteria of earth leakage breakers (ELB) and analyzes the characteristics of an Igc-free ELB operated by an active component which is not misoperated by capacitive current. Even for the same ELB, the earth leakage current flowing through the human body is estimated to be differ greatly depending on the power source, voltage, location and status of contact, contact time duration, etc. Earth leakage breakers are classified based on the rated voltage, rated sensing current, rated operating time etc. Mounting and demounting of the existing equipment can be performed easily since an $I_{gc}$-free ELB is manufactured with the same structure as a conventional ELB. The rated operating current of a conventional and an $I_{gc}$-free ELB is 30mA, the sensing current is 25mA and the rated non-operating current is 15mA. In the analysis of non-operating current characteristics, the rated non-operating current of 15mA was satisfied up to a 20mA charging current in the conventional ELB, but does not satisfy the rated non-operating current as it operates when the resistive leakage current is lower than 15mA for a charging current exceeding 20mA. Also, the ELB is misoperated without a resistive leakage current when the charging current exceeded 25mA. However, the newly developed $I_{gc}$-free ELB satisfied the rated non-operating current even when the charging current was 60mA. Also, in comparison to the interrupting characteristics, it was confirmed that the charging current satisfying the rated non-operating current of the $I_{gc}$-free ELB was three times higher than that of the conventional ELB.