• Journal of the Korea Concrete Institute
• /
• v.15 no.6
• /
• pp.840-847
• /
• 2003

Recently, the coal-ash production has been increased by increase of consumption of electric power. So it is important to secure a reclaimed land and treatment utility for coal-ash. This is an experimental study to compare and analyze the engineering properties of concrete according to W/C and replacement ratio of bottom ash. For this purpose, the mix proportions of concrete according to W/C(40, 50, 60%) and replacement ratio of bottom ash(0, 10, 20, 35, 50%) were established, and then tested for slump, chloride content, setting time, bleeding content, compressive strength. Also the durability test of concrete with W/E 60% was performed. According to test results, it was found that the bleeding content of concrete decreased as the replacement ratio of bottom ash increased. And the chloride content of concrete using the bottom ash increased as the replacement ratio of bottom ash increased, but it is satisfied with the chloride content of fresh concrete $0.30kg/m^3$ below("concrete standard specification" regulation value). The compressive strength of concrete using the bottom ash was similar to that of BA0 concrete after 28 days of curing and the carbonation depth of concrete was increased according to increase of the replacement ratio of bottom ash.

• Journal of Biosystems Engineering
• /
• v.42 no.4
• /
• pp.350-357
• /
• 2017

Purpose: In-situ monitoring of water quality is fundamental to most environmental applications. The high cost and long delays of conventional laboratory methods used to determine water quality, including on-site sampling and chemical analysis, have limited their use in efficiently managing water sources while preventing environmental pollution. The objective of this study was to develop an on-site water monitoring system consisting mainly of an Arduino board and a sensor array of multiple ion selective electrodes (ISEs) to measure the concentration of $NO_3$ ions. Methods: The developed system includes a combination of three ISEs, double-junction reference electrode, solution container, sampling system consisting of three pumps and solenoid valves, signal processing circuit, and an Arduino board for data acquisition and system control. Prior to each sample measurement, a two-point normalization method was applied for a sensitivity adjustment followed by an offset adjustment to minimize the potential drift that could occur during continuous measurement and standardize the response of multiple electrodes. To investigate its utility in on-site nitrate monitoring, the prototype was tested in a facility where drinking water was collected from a water supply source. Results: Differences in the electric potentials of the $NO_3$ ISEs between 10 and $100mg{\cdot}L^{-1}$ $NO_3$ concentration levels were nearly constant with negative sensitivities of 58 to 62 mV during the period of sample measurement, which is representative of a stable electrode response. The $NO_3$ concentrations determined by the ISEs were almost comparable to those obtained with standard instruments within 15% relative errors. Conclusions: The use of the developed on-site nitrate monitoring system based on automatic sampling and two-point normalization was feasible for detecting abrupt changes in nitrate concentration at various water supply sites, showing a maximum difference of $4.2mg{\cdot}L^{-1}$ from an actual concentration of $14mg{\cdot}L^{-1}$.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.19 no.3
• /
• pp.44-53
• /
• 2011

Siloxane, organo-silicon compound, is used in the various forms of products such as cosmetics and detergents due to its quality physical chemistry attributes. Siloxane included in landfill gas which is caused in the process of decomposing of such products after landfill has imposed negative impacts on the operation of landfill gas utility facilities. The objective of this study was to investigate the siloxane production characteristics depending on the features of various landfill site in Korea so that the analysis was made on the landfilling age and landfill waste by in terms of its concentration, structure and composition. As for the concentration of siloxane depending on time passage, 12 landfill sites were reviewed by landfilling age. As for production attributes change of siloxane by landfill wastes, the source of wastes, physical production ration and siloxane concentration were compared in 6 landfills. The average concentration of total-siloxane within LFG is $6.75mg/m^3$ and cyclic-siloxane out of it occupies over 93%. By element, D4 and D5 in order take the highest proportion regardless of total-siloxane concentration and landfilling age. Even though this study is not able to verify the different impact of each kind of wastes on the generation of siloxane, it is confirmed that total-siloxane and cyclic-siloxane decrease in line with the increase of landfilling age as it does in the first order decay model for landfill gas.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.3
• /
• pp.485-492
• /
• 2021

The wind turbines with a rated capacity of 50kW or less are generally considered as small class. Small wind turbines are an attractive alternative for off-grid power system and electric home appliances, both as stand-alone application and in combination with other energy technologies such as energy storage system, photovoltaic, small hydro or diesel engines. The research objective is to develop the 50kW scale wind turbine blades in ways that resemble as closely as possible with the construction and methods of utility scale turbine blade manufacturing. The mold process based on wooden form is employed to create a hollow, multi-piece, lightweight design using carbon fiber and fiberglass with an epoxy based resin. A hand layup prototyping method is developed using high density foam molds that allows short cycle time between design iterations of aerodynamic platforms. A production process of five blades is manufactured and key components of the blade are tested by IEC 61400-23 to verify the appropriateness of the design. Also, wind system with developed blades is tested by IEC 61400-12 to verify the performance characteristics. The results of blade and turbine system test showed the available design conditions for commercial operation.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.2
• /
• pp.131-140
• /
• 2009

It has been repeatedly reported that a drainage system of a drained tunnel is deteriorated. And consequently the water pressure on the lining increases with time. However, little research on the watertight tunnel was found in the literatures. According to field measurements, leakage of the undrained tunnel has increased with time, which is completely opposite to the behavior of the drained tunnel. It is evident that the hydraulic deterioration of the tunnel lining changes the water pressure on the lining and the amount of leakage, thus the design coneept in terms of groundwater is not maintained tightly throughout the life time of the tunnel. The Segment lining is generally constructed as watertight. However, it is frequently reported that the leakage in the segment tunnel increases with time. It is also reported that the leakage is generally concentrated at the joints of the segments. In this study structural and hydraulic interaetion of the segment lining due to the hydraulic deterioration of the segments and the joints is investigated using the numerical modeling method. An electric utility tunnel below groundwater table is considered for the analyses. The effects of hydraulic deterioration of the segment lining are identified in terms of ground loading, water pressure and lining behavior. A remedial grouting measure for leakage is also numerically simulated, and its appropriateness is evaluated.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.93-102
• /
• 2016

Vehicle-to-Grid (V2G) system, bi-direction power trading technology, enables drivers possessing electric vehicle to sell the spare electricity charged in the vehicle to power distribution company. The drivers gain profit by charging electricity in the day time of high electricity rate. In this regard, the government is preparing the policies of building and supporting V2G infrastructure and demanding the potential consumers' preference for the V2G system. This paper attempts to analyze the consumers' preference using the data from obtained a survey of randomly selected 1,000 individuals. To this end, choice experiment, an economic technique, is employed here. The attributes considered in the study are residual amount of electricity, electricity trading hours, required plug-in time, and price measured as an amount additional to current gasoline vehicle price. The multinomial logit model, which requires the assumption of 'independence of irrelevant alternatives', is applied but the assumption could not be satisfied in our data. Thus, we finally utilized nested logit model which does not require the assumption. All the parameter estimates in the utility function are statistically significant at the 10% level. The estimation results show that the marginal willingness to pay (MWTP) for one hour increase in electricity trading hours is estimated to be KRW 1,601,057. On the other hand, a one percent reduction in residual amount of electricity and one hour reduction in required plug-in time in V2G system are computed to be KRW -91,911 and -470,619, respectively. The findings can provide policy makers with useful information for decision-making about introducing and managing V2G system.

• Journal of Global Scholars of Marketing Science
• /
• v.20 no.2
• /
• pp.173-178
• /
• 2010

A privately held, third generation family owned company, Boom Technologies, Inc. (BTI), a provider of products and services to the electric utility, telecommunications and contractor markets, continues to make progress in exporting. Although export sales only equaled 5% of total revenue in 2008, BTI has an entire export division. Their export division's Managing Director reveals the trial and errors of a privately held company and their quest for success overseas. From its inception, BTI has always believed its greatest asset is its employees. When export sales struggled due to lack of strategy and direction, BTI hired a Managing Director for its export division. With leadership and guidance from BTI's president and from the Managing Director, they utilized the department's skills and knowledge. Structural changes were made to expand their market presence abroad and increase export sales. As a result, export sales increased four-fold, area managers in new countries were added and distribution networks were successfully cultivated. At times, revenue generation was difficult to determine due to the structure of the company. Therefore, in 1996, the export division was restructured as a limited liability company. This allowed the company to improve the tracking of revenue and expenses. Originally, 80% of BTI's export sales came from two countries; therefore, the initial approach to selling overseas was not reaching their anticipated goals of expanding their foreign market presence. However, changes were made and now the company manages the details of selling to over 80 countries. There were three major export expansion challenges noted by the Managing Director: 1. Product and Shipping - The major obstacle for BTI was product assembly. Originally, the majority of the product was assembled in the United States, which increased shipping and packaging costs. With so many parts specified in the order, many times the order would arrive with parts missing. The missing parts could equate to tens of thousands of dollars. Shipping these missing parts separately in another shipment also cost tens of thousands of dollar, plus a delivery delay time of six to eight weeks; all of which came out of the BTI's pockets. 2. Product Adaptation - Safety and product standards varied widely for each of the 80 countries to which BTI exported. Weights, special licenses, product specification requirements, measurement systems, and truck stability can all differ from country to country and can serve as a type of barrier to entry, making it difficult to adapt products accordingly. Technical and safety standards are barriers that serve as a type of protection for the local industry and can stand in the way of successfully pursuing foreign markets. 3. Marketing Challenges - The importance of distribution creates many challenges for BTI as they attempt to determine how each country prefers to operate with regard to their distribution systems. Some countries have competition from a small competitor that only produces one competing product; whereas BTI manufactures over 100 products. Marketing material is another concern for BTI as they attempt to push marketing costs to the distributors. Adapting the marketing material can be costly in terms of translation and cultural differences. In addition, the size of paper in the United States differs from those in some countries, causing many problems when attempting to copy the same layout and With distribution being one of several challenges for BTI, the company claims their distribution network is one of their competitive advantages, as the location and names of their distributors are not revealed. In addition, BTI rotates two offerings yearly: training to their distributors one year and then the next is a distributor's meeting. With a focus on product and shipping, product adaptation, and marketing challenges, the intricacies of selling overseas takes time and patience. Another competitive advantage noted is BTI's cradle to grave strategy, where they follow the product from sale to its final resting place, whether the truck is leased or purchased new or used. They also offer service and maintenance plans with a detailed cost analysis provided to the company prior to purchasing or leasing the product. Expanding abroad will always create challenges for a company. As the Managing Director stated, "If you don't have patience (in the export business), you better do something else." Knowing how to adapt quickly provides BTI with the skills necessary to adjust to the changing needs of each country and its own unique challenges, allowing them to remain competitive.

• Journal of Global Scholars of Marketing Science
• /
• v.19 no.2
• /
• pp.17-26
• /
• 2009

As the lifestyle of consumers changes and the need for various products increases, new products are being developed in the market. Each household owns various home appliances which are purchased through the choice of a decision maker. These appliances include not only large-sized products such as TV, refrigerator, and washing machine, but also small-sized products such as microwave oven and air cleaner. There exists latent correlation among possession of home appliances, even though they are purchased independently. The purpose of this research is to analyze the effect of demographic factors on the purchase and possession of each home appliances, and to derive some relationships among various appliances. To achieve this purpose, the present status on the possession of each home appliances are investigated through consumer survey data on the electric and energy product. And a multivariate probit(MVP) model is applied for the empirical analysis. From the estimation results, some appliances show a substitutive or complementary pattern as expected, while others which look apparently unrelated have correlation by co-incidence. This research has several advantages compared to previous literatures on home appliances. First, this research focuses on the various products which are purchased by each household, while previous researches such as Matsukawa and Ito(1998) and Yoon(2007) focus just on a particular product. Second, the methodology of this research can consider a choice process of each product and correlation among products simultaneously. Lastly, this research can analyze not only a substitutive or complementary relationship in the same category, but also the correlation among products in the different categories. As the data on the possession of home appliances in each household has a characteristic of multiple choice, not a single choice, a MVP model are used for the empirical analysis. A MVP model is derived from a random utility model, and has an advantage compared to a multinomial logit model in that correlation among error terms can be derive(Manchanda et al., 1999; Edwards and Allenby, 2003). It is assumed that the error term has a normal distribution with zero mean and variance-covariance matrix ${\Omega}$. Hence, the sign and value of correlation coefficients means the relationship between two alternatives(Manchanda et al., 1999). This research uses the data of 'TEMEP Household ICT/Energy Survey (THIES) 2008' which is conducted by Technology Management, Economics and Policy Program in Seoul National University. The empirical analysis of this research is accomplished in two steps. First, a MVP model with demographic variables is estimated to analyze the effect of the characteristics of household on the purchase of each home appliances. In this research, some variables such as education level, region, size of family, average income, type of house are considered. Second, a MVP model excluding demographic variables is estimated to analyze the correlation among each home appliances. According to the estimation results of variance-covariance matrix, each households tend to own some appliances such as washing machine-refrigerator-cleaner-microwave oven, and air conditioner-dish washer-washing machine and so on. On the other hand, several products such as analog braun tube TV-digital braun tube TV and desktop PC-portable PC show a substitutive pattern. Lastly, the correlation map of home appliances are derived using multi-dimensional scaling(MDS) method based on the result of variance-covariance matrix. This research can provide significant implications for the firm's marketing strategies such as bundling, pricing, display and so on. In addition, this research can provide significant information for the development of convergence products and related technologies. A convergence product can decrease its market uncertainty, if two products which consumers tend to purchase together are integrated into it. The results of this research are more meaningful because it is based on the possession status of each household through the survey data.