• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1945-1947
• /
• 2000

In this paper, we manufactured the detector which is detecting the periodical distribution of arrival time about pulsed leaky noise. The frequency range were analyzed optimally pulsed leaky noise in detector design. With results we can make the detector for leaky noise from the bad insulator.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2594-2599
• /
• 2008

This study deals with the development of PMSM(Permanent Magnet Synchronous Motor) for automotive EDC(Electric Drive Compressor). We have already developed the previous version of PMSM. It showed the characteristics of small size and high efficiency. But noise and vibration levels were higher than target values, so it was impossible to apply. So, in order to reduce noise and vibration levels, many parameters like the numbers of slots, the numbers of winding turns, and slot open width were changed. As a result, noise level of newly developed PMSM was decreased about 36.9% at maximum operating frequency (8600 rpm), and was reduced about 37.7% at rated frequency (6000 rpm) with the same sized and more efficient PMSM.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.200-201
• /
• 2002

Recently, a countermeasure for the electromagnetic noise emission on RF integrated transmission line using the loss generation of ferromagnetic thin films is briefly suggested$\^$1,2/. Without the magnetic film, the noise harmonics of the signal pass through the transmission line with only a little attenuation. The ideal role of magnetic film is not to raise insertion losses in the pass-band and to give as large attenuation as possible to eliminate the noise harmonics at the stop-band, the frequency range higher than the meaningful signal as shown in Fig. 1. and Fig. 2. (omitted)

• Journal of electromagnetic engineering and science
• /
• v.5 no.2
• /
• pp.61-65
• /
• 2005

In this paper, a numerical permissible disturbance model is proposed to preserve a throughput performance of a 2.4 GHz wireless LAN service. The model is composed of two parameters, a peak value and a time rate of noise signal. The model parameters are experimentally determined from an APD parameter measurement. The APD parameter is measured by using the APD measurement method which is recommended from CISPR/A/447/CD.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.239-242
• /
• 2005

This paper introduced an approach of improvement of performance of Electric device for EMU type Train like as TTX. The electric equipments are characterized by insulation, Noise, cooling system etc. and Their weight arc decided by these factors. There are two kinds of power source in EMU train. First, DC voltage source, 1500 volt, 750 volt is used for subway system. Second, AC power source 25000 volt is applied to high speed train and existing main lines. Composite material has the protection of inrush current and high frequency noise. We can use this material to minimize weight of train. Additionally we can get energy saving when operator service TTX.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.831-836
• /
• 2004

Vibration of electric-powered hand grinder comes from the parts of motor, gear, bearing, and fan. Excessive vibration can be harmful to workers. To reduce vibration of a hand grinder we analyzed the frequency components from the routing electric-powered grinder and did modal test to find the natural frequencies of the each part. It shows that the vibration is due to the resonance of the case. To remove the resonance, the case structure is modified and the bearing cap is replaced on a basis of the results from the rotor dynamic analysis using SAMCEF. As a result the vibration of the hand grinder is reduced greatly.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.33 no.5
• /
• pp.463-468
• /
• 2009

Torsional oscillations of the drivetrain in electric vehicles are generated under rapid driving conditions. These lead to an uncomfortable jerking of the vehicle and an increased stress of the mechanical components. To suppress torsional oscillations, the low pass and notch filters between the torque command from the acceleration pedal and electric motor input torque are suggested. The filter parameters are optimized based on Taguchi method with $L_{18}(3^5)$ orthogonal array. The signal to noise (S/N) ratio mainly depends on slew rate of motor input torque, damping ratio and natural frequency of notch filter. With the proposed suppression control scheme, the S/N ratio is shown to be increased by 4.7dB and the torque overshoot of the drive shaft is reduced to 30%.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.11
• /
• pp.73-82
• /
• 2008

A dynamic model of reducer for generating facility of electric pourer having bevel gear pair and planetary gear train is developed by lumped method. The model accounts for the shaft and bearing flexibilities, gyroscopic effects and the force couplings among the transverse and torsion motions due to gearing. Vibration/noise analysis as well as strength of bevel gear pair and planetary gear train are considered. Exciting forces of high reducer for generating facility of electric power areconsidered as the mass unbalance of the rotors, misalignment and a function of gear transmission error. A Campbell diagram, in which the excitation sources caused by the mass unbalance of the rotors, misalignment and the transmitted errors of the gearing are considered, shows that, at the operating speed, there are not critical speed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.189-192
• /
• 2014

Recently, development of electric powered UAV for high altitude and long endurance mission has been conducted worldwide. Long endurance requirement necessitates high lift over drag (L/D) aerodynamic characteristics and lightweight structures, leading to highly flexible wings with high aspect ratio. These highly flexible wings increase the danger of catastrophic aircraft failure due to flutter, which is a dynamic aeroelastic instability occurring from the interaction of aerodynamic, inertial, and elastic forces acting on the aircraft flying through the air. In this paper, flexible wing for electric powered UAV whose skin is fabricated using mylar film for lightweight design is briefly explained. In addition, flutter analysis procedures and results for the flexible wing in order to substantiate the aeroelastic stability requirements are presented.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.4
• /
• pp.889-897
• /
• 2001

Recently, a lot of studies on the power line communication(PLC) are being done by many companies and institutes due to its own merit which can use the power line spread widely as a communication channel. But, there are many serious problems about the harsh and unpredictable characteristics, or noise, signal distortion and attenuation to be overcome for commercialization. In this paper, the power line characteristics as the view point of communication channel are investigated and the technologies of PLC are proposed to control the power of electric machineries by using the combined method of ASK modulation and microprocessor technologies. Also experiments are carried out to ascertain performance in case of applying to electric lights control according to various distancea as an example.