• 전자공학회논문지SC
• /
• 제48권4호
• /
• pp.47-53
• /
• 2011

전동차 출입문은 포켓 슬라이딩 도어, 아웃 슬라이딩 도어, 플러그 도어로 구분된다. 현재 국내 전동차의 표준규격으로 제시되어 있는 포켓 슬라이딩 도어는 철도차량이 고속화됨에 따라 소음 및 외풍의 차단이 어려운 단점이 있으며, 아웃 슬라이딩 도어 역시 소음 및 외풍차단이 어려운 시스템이다. 반면에 플러그 도어는 최근 철도차량이 고급화됨에 따라 고속철도에 적용되던 출입문을 전동차에 적용하면서 쓰이게 된 도어시스템으로 승차감 개선에 소음이 중요한 위치를 차지함에 따라 소음에 강한 플러그 도어 시스템이 주목받고 있다. 이러한 이유로 차세대전동차에 적용할 목적으로 전기식 플러그 도어를 개발하여 시험 진행 중에 있다. 플러그 도어를 구성하는 하부 부품으로는 출입문 제어 장치 (DCU : Door Control Unit), 모터, 스크루 기어, 볼 너트, 레일, 리미트 스위치, 각종 전기 장치, 비상 수동 개폐장치, 코디네이션 바 등이 있는데 이중 DCU는 전동차 출입문을 개폐하기 위한 제어장치로 량당 8개인 전동차 출입문이 동시에 열리고 닫히기 위해서는 각 출입문간의 인터페이스가 필요하며, 승객의 승하차와 직접적으로 관련되어 있기 때문에 신뢰성 및 안전성 확보가 매우 중요한 시스템이다. DCU의 기능으로는 자동 문 여닫음 제어, 출입문 제어 및 장애 감지, 출입문 상태 제어, 저전압/고전압 감시 등이 있으며, 본 논문에서는 전기식 플러그 도어에 적용하기 위해 개발된 DCU의 기능, 개발요구사양, 시스템 구성 및 시험결과에 대해 논하고자 한다.

• 한국정밀공학회지
• /
• 제27권10호
• /
• pp.77-83
• /
• 2010

In this paper, the noise of HEV(hybrid electric vehicle)-relay module during the turn-on and turnoff switching is experimentally analyzed and an effective method is proposed to reduce the impact noise. First, enclosure methods of 100A relay part with urethane and silicon are tested to find out a better material to isolate the noise. This result shows that the urethane is a better for the noise isolation of relay, so the relays enclosed by urethane are installed in the relay module. Second, the noise of HEV-relay module is analyzed experimentally to identify the noise generation mechanism. From this result, it is found that the vibration transmitted to battery pack through bolt generates the structural borne noise with the frequency band of 200~2000 Hz, which is more serious when the switch is turned off. Finally, the direction of switching and the joint structure are modified in order to isolate the vibration transmitted to battery back. Both methods are very effective to reduce the switching noise.

• 한국정밀공학회지
• /
• 제28권4호
• /
• pp.427-435
• /
• 2011

This paper deals with the measurement and analysis of the squeal noise according to the curvature of rail. The squeal noise is generated by the friction between the railway with curve and the wheel. The squeal noise is a big problem in Busan Metro Line 3. If the developing panel type ANC(Active Noise Control) system which is attached to the floor can reduce 5 dB in below 500 Hz, the sound pressure level of the whole band pass can be reduced about 4-4.8 dB in squeal noise above the curvature of R400. Curve squeal noise is the intense high frequency tonal that can occur when a railway vehicle transverses a curve. The frequency range is from around 500 to almost 20,000 Hz, with noise levels up to about 15 dB in curve.

• 한국소음진동공학회논문집
• /
• 제26권4호
• /
• pp.475-482
• /
• 2016

The active control of noise generated by the compressor and transmitted out of the machine room through the windows is implemented based on the FIR filter. The machine room contains most of noise sources of electric home appliances, air-conditioners and refrigerators, for example. To actively reduce the noise from the machinery room. In this paper, the transfer function of the controller for minimization of the acoustic power transmitted through the windows is mathematically formulated. The transfer functions required for implementation of the active controller are the measured. The measurements are conducted in this initial stage under the operation of the compressor with no load. For improvement of the reliability of the transfer function of the compressor to the acoustic power, additional operational measurements are performed. The real time controller is implemented based on the FIR filter using the measured transfer functions and the performance of the active controller is estimated. Control performance is measured about 3 dB ~ 10 dB in reduction of the sound power at the peaks of the compressor noise.

• 지구물리와물리탐사
• /
• 제3권3호
• /
• pp.83-87
• /
• 2000

송신원의 파워 증가가 제한되고 인공잡음이 존재하는 지역에서 양질의 탄성파 자료를 획득하기 위하여 근/원기준점(reference)을 이용한 탄성파 잡음예측필터를 개발하였다. 잡음예측필터에 사용된 방법은 backpropagation 알고리즘을 이용한 3층의 인공신경망(neural network)으로서, 훈련자료(training data) 및 검증자료(testing data)에 훈련된 잡음예측필터를 적용시 신호대잡음비(signal-to-noise ration)를 약 3배 정도 증가시켰다. 그러나, 일반적으로 전기, 전자탐사 자료의 질을 향상하기 위해 사용되는 스케일링(scaling)기법으로는 전혀 탄성파의 잡음을 제거할 수 없었다.

• 한국공작기계학회논문집
• /
• 제14권3호
• /
• pp.38-46
• /
• 2005

The destructive method is reliable and widely used for the estimation of material degradation but it have time-consuming and a great difficulty in preparing specimens from in-service industrial facilities. Therefore, the estimation of degraded structural materials used at high temperature by nondestructive evaluation such as electric resistance method, replica method, Barkhausen noise method, electro-chemical method and ultrasonic method are strongly desired. In this study, various nondestructive evaluation(NDE) parameters of the Barkhausen noise method, such as MPA(Maximum Peak Amplitude), RMS, IABNS(Internal Area of Barkhausen Noise on Signal) and average amplitude of frequency spectrum are investigated and correlated with thermal damage level of 2.25cr-1.0Mo steel using wavelet analysis. Those parameters tend to increase while thermal degradation proceeds. It also turns out that the wavelet technique can help to reduce experimental false call in data analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 학술대회 논문집 전문대학교육위원
• /
• pp.191-193
• /
• 2007

Pantograph sliding plate abrasion auto-detect system, one of the electric rail car auto-detecting devices, is a system that decides how much abrasion and when to replace without an inspector physically looking at the abrasion on the wet plate using machine vision, a cutting-edge technology. This paper covers the cause of deteriorating reliability that affects pantograph wet plate edge detection due to noise added to the video when it rains. In order to remove such noise, problems should be checked through Smoothing, Averaging mask and Median filter using filtering technique and stable edge detection without being affected by noise should be induced in video measurement used in machine vision technology.

• 조명전기설비학회논문지
• /
• 제29권6호
• /
• pp.78-89
• /
• 2015

Conventional EMI filters have tried to use an active EMI filter as a series by the series connection of two EMI filters for CM and DM noise. However, the proposed filter is formed into one circuit by using the active EMI filter which is able to filter CM and DM noise components together. As a result, the active EMI filter showed the outstanding quality in mass and volume under 50% and electric characteristics have been compared to the passive EMI filter in approximately 150kHz~10MHz. Furthermore, the proposed circuit has simple circuit components by comparing with the series EMI filters, and electrical characteristics are similar. The noise have been attenuated to maximum 20dBuV.

• Journal of information and communication convergence engineering
• /
• 제15권4호
• /
• pp.237-243
• /
• 2017

This paper presents an analysis of the electromagnetic interference of a heterogeneous power bus where electromagnetic bandgap (EBG) cells are irregularly arranged. To mitigate electrical-noise coupling between high-speed circuits, the EBG structure is placed between parallel plate waveguide (PPW)-based power buses on which the noise source and victim circuits are mounted. We examine a noise suppression characteristic of the heterogeneous power bus in terms of scattering parameters. The characteristics of the dispersion and scattering parameters are compared in the sensitivity analysis of the EBG structure. Electric field distributions at significant frequencies are thoroughly examined using electromagnetic simulation based on a finite element method (FEM). The noise suppression characteristics of the heterogeneous power bus are demonstrated experimentally. The heterogeneous power bus achieves significant reduction of electrical-noise coupling compared to the homogeneous power buses that are adopted in conventional high-speed circuit design. In addition, the measurements show good agreement with the FEM simulation results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2004년도 춘계학술대회논문집
• /
• pp.1047-1051
• /
• 2004

Charge amplifier systems benefit from the very wide dynamic range of PE accelerometers by offering flexibility in adjusting the electrical output characteristics such as sensitivity and range. They are well suited for operation at high temperatures. Modern charge systems feature improved low noise operation, simplified digital controls, and dual mode operation for operation with charge or IEPE voltage mode sensors. high impedance circuitry is not well suited for operation in adverse field or factory environments. The resolution of a PE accelerometer may not be specified or known since noise is a system consideration determined by cable length and amplifier gain. IEPE accelerometrs operate from a constant current power source, provide a high-voltage, low-impedance, fixed mV/g output. They operate through long, ordinary, coaxial cable in adverse environments without degradation of signal quality. They have limited high temperature range. IEPE sensors are simple to operate. Both resolution and operating range are defined specifications. Cost perchannel is lower compared to PE systems since low-noise cable and charge amplifiers are not required.