• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.21 no.11
• /
• pp.997-1004
• /
• 2011

A fault detection algorithm of a charge and discharge system to ensure the safe use of hybrid electric vehicle is proposed in this paper. This algorithm can be used as a complementary way to existing fault detection technique for a charge and discharge system. The proposed algorithm uses a SVDD technique, which additionally utilizes two methods for learning a large amount of data; one is to incrementally learn a large amount of data, the other one is to remove the data that does not affect the next learning using a new data reduction technique. Removal of data is selected by using lines connecting support vectors. In the proposed method, the data processing speed is drastically improved and the storage space used is remarkably reduced than the conventional methods using the SVDD technique only. A battery data and speed data of a commercial hybrid electrical vehicle are utilized in this study. A fault boundary is produced via SVDD techniques using the input and output in normal operation of the system without using mathematical modeling. A fault detection simulation is performed using both an artificial fault data and the obtained fault boundary via SVDD techniques. In the fault detection simulation, fault detection time via proposed algorithm is compared with that of the peak-peak method. Also the proposed algorithm is revealed to detect fault in the region where conventional peak-peak method is never able to do.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.1
• /
• pp.92-98
• /
• 2013

There are lots of studies about hybrid electric vehicles (HEVs) because of the global warming and energy problems. Series and parallel HEVs are the common types of many developing hybrid vehicle types. Series HEV uses engine only as the generator for the battery but parallel HEV utilizes engine for driving and generating of the vehicle. In this paper, backward simulations based on dynamic programming were conducted for the fuel economy analysis of two different types of hybrid transit buses depending on driving cycles. It is shown that there is a relation between the type of HEV and the characteristics of driving cycles. Regarding the aggressiveness, the series hybrid bus is more efficient than the parallel system on highly aggressive driving cycle. On the other hand, the parallel hybrid bus is more efficient than the series system on low aggressive driving cycle. Based on this results of the paper, it is expected to choose more efficient type of the hybrid buses according to the driving cycle.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.4
• /
• pp.150-159
• /
• 2021

This study aimed to prevent inconvenience to electric vehicle users caused by an interruption of charging by the earth leakage breaker trip that occurs during charging. As a field case study, it was confirmed that during the battery charger failure type, leakage current measurement experiment by vehicle type, and leakage current breaker operation experiment, the internal temperature of the charger rose to more than 60 ℃ in summer, and the earth leakage circuit breaker stopped charging by tripping at 80% of the rated sensitivity current. Through Joule heating modeling, 32A is energized at the reference temperature of 30 ℃ at the initial time t=0 (s). After t=3000 (s), the heat generated around the charging part of the earth leakage breaker increased to 32.4 ℃. The temperature and time factors correlated with the amount of heat generated according to the statistical verification tool with a correlation coefficient of 0.97. Overall, it is possible to prevent the leakage breaker sensitivity current trip due to an increase in temperature inside the charger in summer by performing a Joule heating simulation according to the material of the charging case, the arrangement of the internal wiring, and the dielectric medium when developing the charger device.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.63 no.6
• /
• pp.738-745
• /
• 2014

Recently, various measures have been discussed for overcoming depletion of fossil fuels and environmental pollution. One of the measures is electric vehicles. But electric vehicles has some limitations from high cost of battery and low efficiency, so operation distance of electric cars is limited. Also there are difficulties that charging lines should be connected by an electric car whenever it charges. Thus, many studies have been conducted to overcome the limitation using conventional batteries of electric vehicles. As a result, the OLEV(On-Line Electric Vehicle) was developed. But the OLEV system is some limitations. The OLEV system causes power quality problems when it charges. Power quality problem cannot be ignored because OLEV systems are closely connected by distribution grids. In this paper, the OLEV system is designed by using PSCAD/EMTDC, and the power quality is measured and evaluated. Power quality is divided by two cases; harmonics and high-frequency. Harmonics were evaluated according to IEEE Std. 519-1992. But the evaluation of High-frequency could not take it because there was no standard. For this reason, the data measured by OLEV system was compared with the EN50065 regulation.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.2
• /
• pp.85-91
• /
• 2016

The Positive Temperature Coefficient (PTC) is used for cabin air heating of a battery electric vehicle, which is different from conventional vehicles. Since the PTC heater consumes a large quantity of power in a parasitic manner, many valuable studies have been reported in the field of alternative heat pumps. In this study, a model for an R134a heat pump taking into account the thermal environment of the cabin was developed for a MATLAB/SIMULINK(R) platform. Component and cabin models are validated with reference values. Results show that the heat pump is more competitive for parasitic power consumption over all ambient temperature conditions. Additionally, the method of waste heat recovery to overcome disadvantages when temperatures are below zero is applied to efficiently operate the heat pump.

• Design & Manufacturing
• /
• v.18 no.3
• /
• pp.15-21
• /
• 2024

This study investigates the causes of wrinkle defects in PA12-insulated busbars used in electric vehicles and proposes an improvement method to address these issues. Busbars, essential components for efficient current transmission in electric vehicle battery modules, require complex three-dimensional bending to optimize internal layouts. For this study, oxygen-free copper busbars with a 0.8 mm PA12 insulation coating were subjected to three types of bending tests: flat bending, edge bending, and torsional bending. Experimental results showed that wrinkle defects only occurred during edge bending, while flat and torsional bending modes exhibited no significant issues. Cross-sectional analysis revealed that the PA12 insulation layer's thickness was uneven, with thinner sections on flat areas and thicker accumulation at the comers. This uneven distribution led to poor adhesion between the insulation and copper layers, resulting in the formation of wrinkles, particularly in areas with air gaps ranging from 75 to 250 ㎛. To further analyze the issue, finite element analysis (FEA) of the bending process was performed under adhesive and non-adhesive conditions. The results confirmed that wrinkles formed when the adhesion between the copper and PA12 coating was insufficient. Improved adhesion conditions, achieved through a heat treatment process at 120℃ for 2 hours, significantly reduced the occurrence of wrinkles during edge bending. This study demonstrates that optimizing the adhesion between the insulation coating and the copper busbar, through controlled heat treatment, can prevent wrinkle defects. The findings provide a pathway for enhancing the durability and performance of insulated busbars in electric vehicle applications.

• Proceedings of the KIPE Conference
• /
• 2011.11a
• /
• pp.32-33
• /
• 2011

Recently, researches on SOC(State Of Charge) of batteries are being increased. Techniques of measuring the battery SOC is essential to researches on increasing cycle life of batteries and to electric vehicle battery charging systems. The surface charge phenomenon of lead storage batteries and the needs of SOC measuring techniques are considered. Features of SOC measuring techniques that have been recently developed are also considered.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.6
• /
• pp.63-69
• /
• 2015

Energy Storage Systems (ESSs) are essential in the future power systems because they can improve power usage efficiency. In this paper, we propose the countermeasure for improving the power quality using coordinated control of BESS(Battery Energy Storage System) on EV connected system. To verify the performance of proposed scheme, we simulate on the actual power system of KEPCO and compare the results of voltage variation, frequency variation, and load factor with those of uncoordinated control. From the simulation results, we confirm that frequency and voltage deviation are significantly reduced with proposed coordinated control of BESS.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.1319-1322
• /
• 2015

일반적으로 이차전지를 이용한 에너지 저장 시스템(ESS, Energy Storage System)과 전기 자동차(EV, Electric Vehicle)에 사용되는 전지(Battery)는 용량에 따라 직 병렬로 수십 개에서 수 만개의 배터리가 사용되기도 한다. 이러한 많은 배터리를 제어하고 관리하기 위해 필요한 것이 배터리 관리 시스템(BMS, Battery Management System)이다. 이러한 BMS는 ESS(Energy Storage System, 에너지저장시스템)의 핵심부품으로서, 관련업계에서는 새로운 기술 개발에 박차를 가하고 있다. 따라서 본 논문에서는 최근 개발되고 있는 AC 임피던스를 이용한 SOH 예측 기능을 검증할 수 있는 DSP(Digital Signal Processing) Platform 기반으로 Master-Slave 형태의 BMS를 개발하였으며, Master-Slave간에는 CAN 통신을 이용하여 제어성, 확장성을 용이하게 함으로써, 새로운 SOH 알고리즘 구현 및 성능 검증을 손 쉽게 구현할 수 있게 되었다.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.11 no.2
• /
• pp.94-101
• /
• 1997

This paper proposes the equalizing charger of series connected batteries which are controlled by the time-sharing method. One-chip microprocessor dectcts the terminal voltage of each battery and then determines the charging time inversely proportional to the terminal voltage so that it decrease the un¬balanced capacity. This system is compact and light, therefore it can be applied to portable equipment such as charger for electric vehicle. And it's so effective as to prevent from overcharging which causes their life to shorten.