• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.15 no.1
• /
• pp.39-44
• /
• 2005

A sheet type of green body was made with the mixture of 60 wt% red clay, 20 wt% fly ash, and 20 wt% stone sludge. Indentations were made on the surfaces of sheets to investigate fracture rate of 1 to 5 mm artificial light-weight aggregates by various drying, breaking, and forming methods. Drying methods of green bodies were natural, electric oven, microwave, and fast drying by torch. Breaking methods of green bodies were ballmill Ⅰ, ballmill Ⅱ, free dropping in the box, and mechanical breaking with roller mill. The depth and width of indent on the surface of the sheet were varied and the thickness of green bodies was also changed to investigate effects of indentation on fracture rates. The highest fracture rate of 42 % among the various drying methods was obtained by microwave drying for 210 sec and the highest fracture rate of 65 % among the various breaking method was obtained by ballmill Ⅱ method. In forming method, an yield of larger aggregates than Ф = 5 mm decreased and that of smaller aggregates than Ф = 5 mm in creased with increasing depth of indentation (only in 3 mm thick green body)and with increasing thickness of green body. The size of aggregates was most homogeneous (by judging from the measurement of aspect ratio of 1 to 5 mm aggregates.) when 3 mm thick green body was rapidly dried by torch and was broken by ballmill Ⅱ method.

• Korean Chemical Engineering Research
• /
• v.52 no.6
• /
• pp.796-806
• /
• 2014

The key for the commercial deployment of IGCC power plants or chemical (methanol, dimethyl ether, etc.) production plants based on coal gasification is their economic advantage over plants producing electricity or chemicals from crude oil or natural gas. The better economy of coal gasification based plants can be obtained by co-production of electricity and chemicals. In this study, we carried out the economic feasibility analysis on the process of co-producing electricity and DME (dimethyl ether) using coal gasification. The plant's capacity was 250 MW electric and DME production of 300,000 ton per year. Assuming that the sales price of DME is 500,000 won/ton, the production cost of electricity is in the range of 33~58% of 150.69 won/kwh which is the average of SMP (system marginal price) in 2013, Korea. At present, the sales price of DME in China is approximately 900,000 won/ton. Therefore, there are more potential for lowering the price of co-produced electricity when comparing that from IGCC only. Since the co-production system can not only use the coal gasifier and the gas purification process as a common facility but also can control production rates of electricity and DME depending on the market demand, the production cost of electricity and DME can be significantly reduced compared to the process of producing electricity or DME separately.

• Applied Chemistry for Engineering
• /
• v.26 no.5
• /
• pp.598-603
• /
• 2015

In this study, electrochemical properties of pitch-based activated carbon fibers (ACFs) were investigated by different heat-treatment temperature of the pitch-based ACFs in order to improve the specific capacitance of electric double-layer capacitor (EDLC). The ACFs were prepared by different heat-treatment temperatures of 1050 and $1450^{\circ}C$, after activation with 4 M KOH at $800^{\circ}C$ using stabilized pitch fiber. The specific surface area of prepared ACFs increased from $828m^2/g$ to $987m^2/g$, also the micropore and mesopore volumes of prepared ACFs were increased. These results because pore was produced by desorbing oxygen and hydrogen elements within the ACFs, and pore size was increased by contraction ACFs by heat-treatment process. Because of the porous properties, the specific capacitance was increased from 73 F/g to 119 F/g using cyclic voltammetry with 1 M $H_2SO_4$ at scan rates of 5 mV/s.

• Korean Journal of Materials Research
• /
• v.10 no.3
• /
• pp.233-240
• /
• 2000

In order to fabricate dense cordierite ceramics without sintering aid, thermal behavior of Mg-Al-Si compounds during sintering was investigated. The dispersibility of cordierite suspension in aqueous media was measured by ESA(electrokinetic sonic amplitude). To prevent aggregation and insufficient dispersion of the cordierite sol, the pH of the suspension was controlled to 1.03 and 8.30 by adding $2N\;HNO_3$ and $2N\;NH_4OH$, respectively. Magnesium-aluminum-silicate complex gel coexisted in the specimen which has been gelled at $150^{\circ}C$ fir 12 hours, however several metastable phase such as ${\mu}-cordierite(Mg_2Al_4Si_5O_{18}),\;spine(MgAl_2O_4)\;and\;mullite(Al_6Si_2O_{13})$ existed below $1300^{\circ}C$ Nucleation rates of the two suspension were similar, but densification of the gel was sensitive to the pH of the sol. Densification of the sol with the pH of 8.3 was more pronounced than that of the sol with pH of 1.63.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.3
• /
• pp.679-686
• /
• 2018

A new dust cleaning vehicle is needed to remove fine and ultra-fine particulate matter in subway tunnels. Therefore, the recently developed tunnel cleaning vehicle is equipped with an efficient suction system and cyclone-based prefilter to handle ultra-fine particles. To treat various sizes of particulate matter with an underbody suction system, this paper proposes a cyclone-based prefilter in the suction system and validates the dust removal efficiency through Computational Fluid Dynamics (CFD) analysis using ANSYS FLUENT. Using the created surface and volume mesh, various particle sizes, materials, and fan flow rates, the particles were tracked in the flow with a discrete phase model. As a result, the dust cleaning vehicle at a normal operational speed of 5km/h requires at least a fan flow rate of $1500m^3/min$ and 100mm of suction inlet height from the tunnel track floor. Those suction modules and cyclone-based prefilters in the dust cleaning vehicle reduces the dust accumulation load of the electric precipitator and helps remove the accumulated fine and ultra-fine dust in the subway tunnel.

• Journal of Energy Engineering
• /
• v.22 no.2
• /
• pp.175-183
• /
• 2013

For the optimal design of the vehicle electric system, it is important to have a reliable modeling tool to predict the dynamic behavior of the automotive battery. In this work, a one-dimensional modeling was carried-out to predict the dynamic behaviors of a 12-V automotive lead-acid battery. The model accounted for electrochemical kinetics and ionic mass transfer in a battery cell. In order to validate the modeling, modeling results were compared with the experiment data of the dynamic behaviors of the lead-acid batteries of two different capacities that were mounted on the automobiles manufactured by Hyundai Motor Company. The discharge behaviors were measured with various discharge rates of C/3, C/5, C/10, C/20 and combination. And dynamic behaviors of charge and discharge were measured. The voltage curves from the experiment and simulation were in good agreement. Based on the modeling, the distributions of the electrical potentials of the solid and solution phases, and the current density within the electrodes could be predicted as a function of charge and discharge time.

• Reproductive and Developmental Biology
• /
• v.30 no.2
• /
• pp.125-133
• /
• 2006

This study was conducted to detect the apoptosis incidence in blastocysts and to compare the abundance of Bax, Bcl2L1, VEGF and FGFR2 in in vitro fertilized (IVF), parthenogenetic (PAT) and nuclear transfer (NT) embryos. Oocytes matured for 40 hr were enucleated and reconstructed with confluenced fetal fibroblasts (FFs) derived from a ${\sim}45$ day fetus. Reconstructed eggs were then fused with 2 DC pulses (2.0 kV/cm, $30{\mu}sec$) and cultured with $7.5{\mu}g/ml$ cytochalasin B for 3 hr. Parthenotes (PAT) were produced with the same electric strength and culture for NT eggs. The embryos were cultured in NCSU-23 medium at $39^{\circ}C,\;5%\;CO_2,\;5%\l;O_2$ in air. In 3 runs, set of 10 embryos at the 4-cell to blastocyst stages were used to extract total RNA for analyzing the gene expression patterns of pro-apoptotic (Bax), anti-apoptotic (Bcl2L1), vasculogenesis (VEGF), implantation (FGFR2III) using real-time quantitative PCR. Cleavage and blastocyst rates were significantly higher (P<0.05) in IVF and PAT ($79.3{\pm}8.5\;and\;25.5{\pm}6.1,\;and\;85.0{\pm}6.4\;and\;38.6{\pm}5.5$, respectively)than NT counterparts ($65.1{\pm}5.2\;and\;15.6{\pm}3.0$, respectively). Significantly higher (P<0.05) total cells were observed in IVF controls and PAT ($34.7{\pm}5.8\;and\;38.1{\pm}4.1$) than NT embryos ($24.8{\pm}3.2$). Apoptosis index was significantly lower (P<0.05) in IVF than NT embryos. The Relative abundances (RA) of Bax and VEGF were significantly higher (P<0.05) at blastocyst stage in NT than IVF control. The RA of Bcl2L1 and FGFR2III were significantly higher (P<0.05) at blastocyst stage in IVF than NT. The present study observed the abnormal gene expressions in NT embryos at various developmental stages, suggesting certain clues to find out the cause of the low efficiency of NT to term.

• Structural Engineering and Mechanics
• /
• v.72 no.5
• /
• pp.643-652
• /
• 2019

Protection of cultural heritage and carrying it to the future are at the top of the significant topics of research and implementation in engineering in the 21st century. There are several historical structures in the district of Ahlat located in the east of Turkey on the Lake Van Basin that has harbored many civilizations. Some of such works are the gravestones that are found in the Ahlat Seljuk Cemetery, which is the oldest and largest cemetery in the district. This study firstly provides information about the Ahlat Seljuk Cemetery and the gravestones found in it. Observation-based structural analyses were carried out on these gravestones that are found in this area that are known to have belonged to different civilizations based on their physical and constructional characteristics. These stones were built out of Ahlat stone as single pieces. Information is provided on the damages that have occurred on the gravestones in time and their causes. In general, losses of mass, abrasions, separations, collapses and calcifications due to natural conditions, as well as vegetative formations, were observed in the gravestones. To provide an example of other gravestones within the context of the study, the gravestone that is known to belong to the person named Nureddin Ebu Hasan was selected. As a result of the modeling that was carried out for this gravestone by using the finite elements method, modal analyses were carried out. With these analyses, for the gravestone, period, effective mass participation rates and stress values were calculated. The stress values that were obtained in this study were compared to the material safety stress values that were obtained in previous studies. Additionally, QR code application was created for the gravestone that was selected as an example in the study, and information on this gravestone was transferred to an electronic environment. The QR code application includes different language options, visuals of the gravestone and information on the gravestone. The QR application was also supported with a video of the cemetery where the gravestone is located. With this application, access to information about gravestones will be possible by using tablets and smartphones. With a QR code to be created for each gravestone, these gravestones will obtain identity cards.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.54-62
• /
• 2016

The most efficient system for converting heat to electricity, AMTEC (Alkali Metal Thermal-to-Electric Convertor), is a device that directly converts heat energy to electricity using an alkali metal (sodium) as the working fluid. The AMTEC consists of a low pressure chamber, high pressure chamber, BASE (Beta-Alumina Solid Electrolyte), and artery wick. The main heat loss of the AMTEC system occurs in the low pressure chamber. A high power generation rate is thought to be obtainable by using a high temperature in the BASE. Therefore, to reduce the radiation heat loss, 6 types of radiation shields were examined to reduce the radiative heat loss in the low pressure chamber. The power generation rate of the AMTEC varied depending on the shape of the radiation shield. CFD (Computational Fluid Dynamics) analyses were carried out to optimize the shape of the radiation shield. As a result, the optimum radiation shield was found to consist of a curvature formed at the vertical point, in which case the dimensionless temperature (condenser temperature/BASE temperature) is approximately 0.665 and the maximum power generated is calculated to be 17.69W. Increasing the distance beween the BASE and condenser leads to an increase in the power generated, and the power generated with the longest distance was 17.58 W. The shields with multiple holes and multiple horizontal layers showed power reduction rates of 0.91 W and 2.06 W, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.363-363
• /
• 2008

The development of dry etching process for sapphire wafer with plasma has been key issues for the opto-electric devices. The challenges are increasing control and obtaining low plasma induced-damage because an unwanted scattering of radiation is caused by the spatial disorder of pattern and variation of surface roughness. The plasma-induced damages during plasma etching process can be classified as impurity contamination of residual etch products or bonding disruption in lattice due to charged particle bombardment. Therefor, fine pattern technology with low damaged etching process and high etch rate are urgently needed. Until now, there are a lot of reports on the etching of sapphire wafer with using $Cl_2$/Ar, $BCl_3$/Ar, HBr/Ar and so on [1]. However, the etch behavior of sapphire wafer have investigated with variation of only one parameter while other parameters are fixed. In this study, we investigated the effect of pressure and other parameters on the etch rate and the selectivity. We selected $BCl_3$ as an etch ant because $BCl_3$ plasmas are widely used in etching process of oxide materials. In plasma, the $BCl_3$ molecule can be dissociated into B radical, $B^+$ ion, Cl radical and $Cl^+$ ion. However, the $BCl_3$ molecule can be dissociated into B radical or $B^+$ ion easier than Cl radical or $Cl^+$ ion. First, we evaluated the etch behaviors of sapphire wafer in $BCl_3$/additive gases (Ar, $N_2,Cl_2$) gases. The behavior of etch rate of sapphire substrate was monitored as a function of additive gas ratio to $BCl_3$ based plasma, total flow rate, r.f. power, d.c. bias under different pressures of 5 mTorr, 10 mTorr, 20 mTorr and 30 mTorr. The etch rates of sapphire wafer, $SiO_2$ and PR were measured with using alpha step surface profiler. In order to understand the changes of radicals, volume density of Cl, B radical and BCl molecule were investigated with optical emission spectroscopy (OES). The chemical states of $Al_2O_3$ thin films were studied with energy dispersive X-ray (EDX) and depth profile anlysis of auger electron spectroscopy (AES). The enhancement of sapphire substrate can be explained by the reactive ion etching mechanism with the competition of the formation of volatile $AlCl_3$, $Al_2Cl_6$ or $BOCl_3$ and the sputter effect by energetic ions.