• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.9
• /
• pp.2313-2318
• /
• 2009

In this paper, when the power equipment, which is based on RFID, is managed, it is reviewed the performance of RFID frequency recognition and its scheme is required to manage status information efficiently. The proposed paper is studied for optimization of recognition performance, when tags are attached the power equipment & major components, to diagnosis failure status of power equipment in monitoring service. The results of paper is valuable applying environment of power equipment.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1107-1113
• /
• 2015

Test temperature is an important factor affecting the measurement results of dielectric response of field power transformers. In order to better apply the polarization and depolarization current (PDC) to the condition monitoring of oil-paper insulation system in power transformers, the influences and elimination method of test temperature on PDC characteristic spectroscopy (PDC-CS) were investigated. Firstly, the experimental winding sample was measured by PDC method at different test temperatures, then the PDC-CS was obtained from the measurement results and its changing rules were discussed, which show that the PDC-CS appears a horizontal mobility with the rise of temperature. Based on the rules, the “time temperature shift technique” was introduced to eliminate the influence of test temperature. It is shown that the PDC-CS at different test temperatures can be converted to the same reference temperature coincident with each other.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.274-277
• /
• 2001

This paper describes the simulation study. conducted on the propagation characteristics of AE signal. In the case of gas insulation, such as $SF_6$, the equipment is less affected by the environment condition than air insulation, because the component parts of equipment were placed in the enclosure, which is filled with compressed gas. But. when the breakdown in the electric insulation occurs. it takes much time and economical efforts to repair. Therefore it is very important to diagnose the equipment before the accident. And. in general. UHF and AE signal is the most common transducer to diagnose the state of the power equipment, so, in this investigation, we make a experimental apparatus with aluminum plate and transient analysis with ANSYS to observe the propagation characteristics of AE signal. Through the result of the analysis. we can make a further understanding on the propagation characteristics of AE signal, and get the fundamental skills for the GIS diagnosis.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.274-277
• /
• 2001

This paper describes the simulation study, conducted on the propagation characteristics of AE signal. In the case of gas insulation, such as SF6, the equipment is less affected by the environment condition than air insulation, because the component parts of equipment were placed in the enclosure, which is filled with compressed gas. But, when the breakdown in the electric insulation occurs, it takes much time and economical efforts to repair. Therefore it is very important to diagnose the equipment before the accident. And, in general, UHF and AE signal is the most common transducer to diagnose the state of the power equipment, so, in this investigation, we make a experimental apparatus with aluminum plate and transient analysis with ANSYS to observe the propagation characteristics of AE signal. Through the result of the analysis, we can make a further understanding on the propagation characteristics of AE signal, and get the fundamental skills for the GIS diagnosis.

• Journal of the Korea Convergence Society
• /
• v.11 no.10
• /
• pp.31-36
• /
• 2020

Virtual simulation education, which is one of the methods of executing engineering education, is spreading. In general online education, only theoretical learning-centered lessons and practical training of simple small projects are conducted remotely, and it is necessary to disseminate various educational contents. Due to the spread of smart factories these days, most producers use automatic control to produce, inspect and package their products. The operation of automation equipment is controlled by using electricity, and electricity-related learning is operated in various departments. Due to the characteristics of electricity, it is difficult to learn online due to safety issues and high cost of practical equipment. In this paper, we provide a simulation-based electrical control panel distance learning model to improve the sense of accomplishment of education related to electrical training. Through the experiment of the proposed model, it was confirmed that the learning was more satisfied with the virtual simulation education than the online education using the existing equipment. It is expected that it can be used as a basic course for automation equipment education in the future.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.1
• /
• pp.5-12
• /
• 2014

In this study, we developed the electric heating equipment and applied for soft ground improvement. The developed heat pipe is 4 m-length and consumes 1 kW/m, which is consisted of Ni-Cr wire. It was installed in 3.5~4.5 m below ground surface and heated for 96 hours (48 hours, 2 times). The temperature variation and vapor pressure caused by electric heating was measured by the thermometer and pressure gauge which were installed in the ground (5.0 m), and the tip resistances were measured by static electronic piezo-cone penetration test (CPT). As the results of experiments, 2-order polynomial curve was shown to adjust the variation of tip resistance and the temperature distribution with the horizontal distance from electric heater, whose R2 value is close to 1. In addition, in-situ pore-water pressure and water content was decreased.

• Resources Recycling
• /
• v.21 no.4
• /
• pp.26-34
• /
• 2012

Recently, the recovery of resources from waste material of manufacturing electric and electronic equipment has been investigated. It is very important to extract metallic components from electric and electronic manufacturing processes with the view point of recycling of the used resources as well as an environmental protection. In this paper, open/registered patents of US, JP, EP, and KR and SCI journal related to metal recovery technologies from wastes produced in the electric and electronic manufacturing processes between 1975~2011 were reviewed. Patents and papers were collected using key-words searching and filtered by filtering criteria. The trends of the patents and papers were analyzed by the years, countries, companies, and technologies.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.414-417
• /
• 1999

According to development of power electric technology from industrial field to electronic home appliances, recent SMPS using semiconductor is spread widely. Electric converting instrument uses a sine wave voltage source, namely an usual power source, and it gets a non-sines power source from power source because current flows through one part in waveform of one cycle. This injects higher harmonic source in source part, absorb pollution source. And this cause quality deterioration, durability shortage of electric power instrument, spreading accident of electric solver system, and so on. It can't supply an electric source of good quality in industry, so become an impedimental element in improving productivity and reliance. This study can be used in prediction of hindrance and diagnosis material and intends to suggest a countermeasure about measurement data.

• Journal of the Korean Society of Safety
• /
• v.29 no.3
• /
• pp.28-33
• /
• 2014

Regarding the characteristics of fatal electric shock accident during the past 10 years, fatalities occurred more frequently in July & August, and AM 10-12 PM & 14-16. Also, the electric shock accident is occurred more frequently in the age group from 30 to 40. Especially, the fatal electric shock accident in construction industry covered more than half of total industry. Therefore, it is strongly requested for the protection technology of an electric shock from the low voltage electric path, grounding method and workers. The aim of this study is to propose the policy about the equipment performance standards and/or worker's safety standards to revise the standards for preventing electric shock accidents on safety workings.

• Journal of Auto-vehicle Safety Association
• /
• v.15 no.4
• /
• pp.32-38
• /
• 2023

With the transition from internal combustion engine vehicles to eco-friendly cars, it has become essential to systematically construct an education system for electric vehicles based on high-voltage electric devices. In this study, we discussed the establishment of an educational system for electric vehicles based on high-voltage electric devices and proposed methods for qualifications after completing the education. To ensure systematic education, we presented a classification of learners according to their levels and job competencies. Additionally, we emphasized the importance of providing adequate practical training equipment for courses that require higher qualifications. Finally, to distinguish between the levels of completion of training and practical skills, we highlighted the necessity of implementing a system to certificates to individuals who have successfully completed the systematic training program.