• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 봄 학술발표회 논문집
• /
• pp.53-60
• /
• 1997

The strain localization of concrete is a phenomenon such that the deformation of concrete is localized in finite region along with softening behavior. The objective of this paper is to develope a consistent algorithm for the finite element modeling of localized zone in the analysis of the strain-localization in concrete. For modeling of the localized zone in concrete under strain localization, a general Drucker-Prager failure criterion which can consider nonlinear strain softening behavior of concrete after peak-stress is introduce. The return-mapping algorithm is used for the integration of the elasto-plastic rate equation and the consistent tangent modulus is derived. Using finite element program implemented with the developed algorithms, strain localization behaviors for the different sizes of concrete specimen under compression are simulated.

• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.627-639
• /
• 2016

The analysis of thermally induced stresses in engineering structures is a very important and necessary task with respect to design and modeling of pressurized containers, heat exchangers, aircrafts segments, etc. to prevent them from failure and improve working conditions. So, the purpose of this study is to investigate elasto-plastic thermal stresses and deformations in a thin annular plate embedded into rigid container. To this end, analytical research devoted to mathematically and physically rigorous stress/strain analysis is performed. In order to evaluate the effect of logarithmic thermal gradients, commonly applied to structures which incorporate thin plate geometries, different thermal parameters such as temperature mismatch and varying constraint temperature were introduced into the model of elastic perfectly-plastic annular plate obeying the von Mises yield criterion with its associated flow rule. The results obtained may be used in sensitive to temperature differences aircraft structures where the thermal effects on equipment must be kept in mind.

• Structural Engineering and Mechanics
• /
• 제30권6호
• /
• pp.665-678
• /
• 2008

The beams components subjected to the loading such as axial, bending and cyclic thermal loads were studied in this research. The used constitutive equations are those of elasto-plasticity coupled to ductile and/or creep damage. The nonlinear kinematic hardening behavior was considered in elastoplasticity modeling. The unified damage law proposed for ductile failure and fatigue by the author of Sermage et al. (2000) and Kachanov's creep damage model applied to cyclic creep and low cycle fatigue of beams. Based on the results of the analysis, the shakedown limit loads were determined through the calculation of the residual strains developed in the beam analysis. The iterative technique determines the shakedown limit load in an iterative manner by performing a series of full coupled elastic-plastic and continuum damage cyclic loading modeling. The maximum load carrying capacity of the beam can withstand, were determined and imposed on the Bree's interaction diagram. Comparison between the shakedown diagrams generated by or without creep and/or ductile damage for the loading patterns was presented.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1998년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring 1998
• /
• pp.180-187
• /
• 1998

In this paper the attention is focused on the modeling of reinforced concrete(R/C) wall structures to check effectiveness and reliability of elasto-plastic analysis. A relatively simple and reliable wall model is investigated, which is suitable to be efficiently incorporated in a practical pushover analysis of R/C wall structural systems. Two types of analogous frames have been examined to the stress analysis of shear walls. One analogous frame is similar to the widely used wide-column model, the second analogous frame also is called truss model which includes vertical edge column and braces. Further studies are needed to apply to nonlinear seismic analysis of building structure with R/C shear walls.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1993년도 봄 학술발표회논문집
• /
• pp.27-34
• /
• 1993

Precast large panel structures behave differently form frame and monolithic wall structures under external loads, because of the distinct planes of weakness in the horizontal and vertical joints between panels. These joints may slide and open during shaking, producing large localized changes in the bending and shear stiffness of individual walls. The structural behavior of large precast panel buildings depends on the relative strength and stiffness of the panels and joints. Special modeling are thus required for the analysis of precast panel connections. This study suggests a new analytical modeling and method to obtain the rational estimation of discontinuity and slip movements form the connections of precast large panel structures .

• Computers and Concrete
• /
• 제17권6호
• /
• pp.703-721
• /
• 2016

A novel approach to modeling concrete behavior at the stage of its maturing is presented in this paper. This approach assumes that at any point in the structure, concrete is composed of a set of layers that are activated in time layer by layer, based on amount of released heat that is produced during process of the concrete's maturing. This allows one to assume that each newly created layer has nominal stiffness moduli and tensile/compressive strengths. Hence introduction of explicit stiffness moduli and tensile/compressive strength dependencies on time, or equivalent time state parameter, is not needed. Analysis of plain concrete (PC) and reinforced concrete (RC) structures, especially massive ones, subjected to any kind of straining in their early stage of existence, mostly due to external loads but especially by thermal loading and shrinkage, is the goal of the approach. In this article a simple elasto-plastic softening model with creep is used for each layer and a general layered model behavior is illustrated on one-dimensional (1D) examples.

• 한국강구조학회 논문집
• /
• 제20권3호
• /
• pp.409-419
• /
• 2008

율리신-이바노브 항복 조건을 이용하여 4절점 순수변위 준적합 쉘요소의 정식화를 제안하였다. 기하강성 행렬은 그린 변형률 텐서를 이용하여 휨변형률 및 전단변형률도 기하강성행렬에 고려되었다. 그 결과 접선강성행렬의 해석적인 적분으로 비선형 해석시 매우 효율적으로 계산이 되고 있다. 이 정식은 변형률 경화의 이바노브-유리신 항복조건을 이용하여 재료 비선형 해석시에도 쉽게 적분이 된다. 즉 두께 방향의 적층 적분을 하지 않는 율리신-이바노브의 정식은 대규모의 쉘 구조에도 계산상 아주 적합하다. 검증된 수치 예제에서 만족스러운 결과를 보여주고 있다.

• Computers and Concrete
• /
• 제12권2호
• /
• pp.211-228
• /
• 2013

The structure analyzed in this paper has particular building style and special structural system. It is a rigid-connected twin-tower skyscraper with asymmetrical distribution of stiffness and masses in two towers. Because of the different stiffness between the north and the south towers, the torsion seismic vibration is significant. In this paper, in order to study the seismic response of the structure under both frequent low-intensity earthquakes as well as rare earthquakes at the levels of intensity 7, the analysis model is built and analyzed with NosaCAD. NosaCAD is an nonlinear structure analysis software based on second-development of AutoCAD with ObjectARX. It has convenient modeling function, high computational efficiency and diversity post-processing functions. The deformations, forces and damages of the structure are investigated based on the analysis. According to the analysis, there is no damage on the structure under frequent earthquakes, and the structure has sufficient capacity and ductility to resist rare earthquakes. Therefore the structure can reach the goal of no damage under frequent earthquakes and no collapse under rare earthquakes. The deformation of the structure is below the limit in Chinese code. The time sequence and distribution of damages on tubes are reasonable, which can dissipate some dynamic energy. At last, according to forces, load-carrying capacity and damage of elements, there are some suggestions on increasing the reinforcement in the core tube at base and in stiffened stories.

• 한국지반공학회논문집
• /
• 제20권9호
• /
• pp.65-75
• /
• 2004

본 연구는 토목섬유 보강토 구조물의 보강 메카니즘을 규명하고자 하는 목적으로 실시하였으며, 여기서 보강 메카니즘은 전단에 의한 다짐토의 체적 팽창(부의 다일러턴시)을 토목섬유에 의해 구속 억제하는 과정에서 생성되는 효과로 간주하고 있다. 실물 현장시험은 일본 Kanazawa(1994)에서 실시했으며, 실내시험으로는 등체적 전단시험을 실시하여 강도 및 변형특성을 조사하였고, 시험결과를 이용하여 유한요소해석에 필요한 재료 파라메타를 결정하였다. 또한, 탄소성 유한요소 해석을 실시하여 이론치와 실험 결과치를 정량적으로 비교 분석되었으며, 그 결과 유한요소 해석이 현장 시험을 유용하게 설명할 수 있는 것을 알 수 있었다.

• 전산구조공학
• /
• 제10권4호
• /
• pp.217-228
• /
• 1997

p-version 유한요소법에 의한 고정밀해석은 응력특이가 발생하는 선형탄성 문제에 매우 적합한 방법으로 인식되고 있다. 해석 결과의 정확도, 모델링의 단순성, 입력자료에 대한 통용성 및 사용자와 CPU 시간의 절감 등 여러장점이 선형탄성 문제에 적용되어 우수성이 입증되었지만, 탄소성 해석분야는 아직 적용이 이루어지지 않고 있다. 그러므로 본 논문에서는 일-경화재료에 대한 구성방정식을 이용하여 정식화된 증분소성이론과 소성유동법칙에 근거한 재료비선형 p-version 유한요소모델이 제안되었다. 비선형방정식을 풀기 위해 Newton-Raphson법과 초기강성도법 등의 반복법이 모색되었다. 제안된 모델을 이용하여 개구부를 가진 사각형 평판과 내압을 받는 두꺼운 실린더, 그리고 등분포하중을 받는 원판해석 등의 수치실험이 수행되었다. 한편, p-version 모델에 의한 해석결과는 문헌의 이론값과 상용유한요소프로그램인 ADINA의 해석결과와 비교 검증되었다.