• Computers and Concrete
• /
• 제1권4호
• /
• pp.433-455
• /
• 2004

The paper presents results of FE-calculations on shear localizations in quasi-brittle materials during both an uniaxial plane strain compression and uniaxial plane strain extension. An elasto-plastic model with a linear Drucker-Prager type criterion using isotropic hardening and softening and non-associated flow rule was used. A non-local extension was applied in a softening regime to capture realistically shear localization and to obtain a well-posed boundary value problem. A characteristic length was incorporated via a weighting function. Attention was focused on the effect of mesh size, mesh alignment, non-local parameter and imperfections on the thickness and inclination of shear localization. Different methods to calculate plastic strain rates were carefully discussed.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2006년 창립20주년기념 정기학술대회 및 국제워크샵
• /
• pp.201-204
• /
• 2006

A three-dimensional finite element (FEM) model has been developed to simulate the deformation due to bead on plate welding of curved plates with curvature in the weld direction. By using traditional method such as thermal-elastic-plastic FEM, the weld-induced deformation can be predicted accurately. However, this method is not practical approach to analyze the deformation of large and complex structures such as ship hull structures in view of time and cost. This study is classified from the aspect of equivalent load based on inherent strain near the weld line. Therefore, the residual deformation can be simply computed by elastic analysis. Further more, a practical solution is proposed to consider the contact between the plate and the positioning jig by judging the reaction forces of the jig at calculation step and the effect of the longitudinal curvature is closely considered.

• 대한조선학회논문집
• /
• 제44권5호
• /
• pp.474-481
• /
• 2007

A three-dimensional finite element model has been used to simulate the bead on plate welding of curved steel plates having curvature in the welding direction. By using traditional method such as thermal-elastic-plastic(TEP) finite element analysis. the weld-induced deformation can be accurately predicted. However, three-dimensional finite element analysis is not practical in analyzing the weld-induced deformation of large and complex structures such as ship structures in view of computing time and cost. In this study, used is the equivalent loading method based on inherent strain to illustrate the effect of the longitudinal curvature upon the weld-induced deformation of curved plates.

• Structural Engineering and Mechanics
• /
• 제58권4호
• /
• pp.627-639
• /
• 2016

The analysis of thermally induced stresses in engineering structures is a very important and necessary task with respect to design and modeling of pressurized containers, heat exchangers, aircrafts segments, etc. to prevent them from failure and improve working conditions. So, the purpose of this study is to investigate elasto-plastic thermal stresses and deformations in a thin annular plate embedded into rigid container. To this end, analytical research devoted to mathematically and physically rigorous stress/strain analysis is performed. In order to evaluate the effect of logarithmic thermal gradients, commonly applied to structures which incorporate thin plate geometries, different thermal parameters such as temperature mismatch and varying constraint temperature were introduced into the model of elastic perfectly-plastic annular plate obeying the von Mises yield criterion with its associated flow rule. The results obtained may be used in sensitive to temperature differences aircraft structures where the thermal effects on equipment must be kept in mind.

• Structural Engineering and Mechanics
• /
• 제55권5호
• /
• pp.913-929
• /
• 2015

The ratcheting and strain cyclic behaviour of joined conical-cylindrical shells under uniaxial strain controlled, uniaxial and multiaxial stress controlled cyclic loading are investigated in the paper. The elasto-plastic deformation of the structure is simulated using Chaboche non-linear kinematic hardening model in finite element package ANSYS 13.0. The stress-strain response near the joint of conical and cylindrical shell portions is discussed in detail. The effects of strain amplitude, mean stress, stress amplitude and temperature on ratcheting are investigated. Under strain symmetric cycling, the stress amplitude increases with the increase in imposed strain amplitude. Under imposed uniaxial/multiaxial stress cycling, ratcheting strain increases with the increasing mean/amplitude values of stress and temperature. The abrupt change in geometry at the joint results in local plastic deformation inducing large strain variations in the vicinity of the joint. The forcing frequency corresponding to peak axial ratcheting strain amplitude is significantly smaller than the frequency of first linear elastic axial vibration mode. The strains predicted from quasi static analysis are significantly smaller as compared to the peak strains from dynamic analysis.

• Geomechanics and Engineering
• /
• 제18권3호
• /
• pp.225-234
• /
• 2019

A numerical stepwise approach for cavity expansion problem in strain-softening rock or soil mass is investigated, which is compatible with Mohr-Coulomb and generalized Hoek-Brown failure criteria. Based on finite difference method, plastic region is divided into a finite number of concentric rings whose thicknesses are determined internally to satisfy the equilibrium and compatibility equations, the material parameters of the rock or soil mass are assumed to be the same in each ring. For the strain-softening behavior, the strength parameters are assumed to be a linear function of deviatoric plastic strain (${\gamma}p^*$) for each ring. Increments of stress and strain for each ring are calculated with the finite difference method. Assumptions of large-strain for soil mass and small-strain for rock mass are adopted, respectively. A new numerical stepwise approach for limited pressure and plastic radius are obtained. Comparisons are conducted to validate the correctness of the proposed approach with Vesic's solution (1972). The results show that the perfectly elasto-plastic model may underestimate the displacement and stresses in cavity expansion than strain-softening coefficient considered. The results of limit expansion pressure based on the generalised H-B failure criterion are less than those obtained based on the M-C failure criterion.

• 한국지반신소재학회논문집
• /
• 제19권1호
• /
• pp.93-101
• /
• 2020

흙의 비선형적 거동특성을 예측하기 위해 비교적 간편하고 예측의 정도가 높은 것으로 평가되는 탄·소성 쌍곡선모델을 선정하였다. 모델의 특성을 알아보기 위해 구성모델에 관련된 함수를 정식화하여 토질매개변수 결정 및 거동해석 프로그램을 개발하였다. 상대밀도 변화에 따른 백마강모래의 배수삼축압축시험 결과로부터 각각의 토질매개변수를 결정하였고 상대밀도에 따른 토질매개변수의 변화 특성을 분석하였으며 각각의 조건에서 결정된 토질매개변수를 이용하여 응력-변형률 거동을 예측하였다. 그 결과 축변형률에 대한 축차응력은 각각의 상대밀도에서 측정치와 예측치가 양호하게 일치하는 것을 확인하였고 축변형률에 대한 체적변형률의 관계에서 상대밀도가 작은 경우는 측정치와 예측치가 일치하는 경향을 보이나 상대밀도가 큰 경우에는 구성모델의 한계로 인해 체적변형률의 예측치가 측정치보다 다소 작게 나타나는 것을 확인 하였다.

• 한국농공학회논문집
• /
• 제55권2호
• /
• pp.87-95
• /
• 2013

The aim of this study is to examine the behavior of reservoir fill dam with the water level raising by use of the centrifugal model test and the numerical simulation. In this study, LIQCA2D-SF based on the cyclic elasto-plastic constitutive model proposed by Oka et al. (1999) is applied for numerical simulation. In order to investigate the displacements and the pore water pressures in the fill dam due to the water level raising velocity, three model tests in centrifugal field of 50g for fill dams were conducted. A comparison between the test result and the simulation result has provided the influence on the displacement and the pore water pressure of the fill dam with increasing up of the water level.

• Architectural research
• /
• 제16권1호
• /
• pp.27-35
• /
• 2014

Nonlinear analysis of reinforced concrete structures is carried out by using Reissner-Mindlin (RM) shell finite element (FE). The brittle inelastic characteristic of concrete material is represented by using the elasto-plastic fracture (EPF) material model with the relevant material models such as cracking criteria, shear transfer model and tension stiffening model. In particular, assumed strains are introduced in the formulation of the present shell FE in order to avoid element deficiencies inherited in the standard RM shell FE. The arc-length control method is used to trace the full load-displacement path of reinforced concrete structures. Finally, four benchmark tests are carried out and numerical results are provided as future reference solutions produced by RM shell element with assumed strains.

• 한국농공학회지
• /
• 제36권2호
• /
• pp.67-78
• /
• 1994

This is a fundamental study aiming at scrutinizing the effect of reinforcement and deformation characteristics of soft clayey foundation improved by vanous technical treatments. Among many methods proposed thus far, geotextile was selected for the purpose of improvement of the model soil foundation on which plate loading test was subsequently performed. Loading test has been carried out with the variation of the location and number of covering layers of geotextile, and actual values for ground deformation and geotextile effect were secured. As for technique on deformation analysis, elasto-plastic model for soil, elastic model for sand, and beam theory for geotextile were coupled with satisfactory results between observed and numerical values.