• Journal of Mechanical Science and Technology
• /
• 제18권8호
• /
• pp.1319-1326
• /
• 2004

Transient 3-dimensional elasto-hydrodynamic lubrication (EHL) analysis is performed on the contacting teeth surfaces of involute spur gears. Kinematics of the gear and the pinion are taken into account to get accurate geometric clearance around the EHL region of the contacting teeth. The surface pressure and film thickness distribution for the whole contact faces in a lubricated condition at several time steps are obtained through the analysis. Besides the pressure spike at the outlet region, a representative phenomenon in EHL regime, the pressure at the inlet region is slightly higher than that of the center region. The film thickness of transient condition is thicker than that of steady condition.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2004년도 유체기계 연구개발 발표회 논문집
• /
• pp.98-103
• /
• 2004

This paper presents modeling and simulation of the bump foil bearings with consideration of the elastic behavior of the foil and gas compressibility. Heshmat had originally introduced the simple compliance model to estimate the EHL(elasto-hydrodynamic lubrication) performance. But this approach can not consider the deflection of top foil at the edge of bearing, so model is insufficient to analyze in case that the eccentricity ratio is greater than I. So the top foil is considered as a simple beam model supported by linear spring elements, and the bump foil deflection can be simple compliance model. The EHL calculations are performed for convention rigid type, classical foil type, variable pitch type and double bump type toil bearings. This paper presents that 2nd or 3rd generation bearings have excellent performance in every speeds.

• Tribology and Lubricants
• /
• 제38권6호
• /
• pp.281-286
• /
• 2022

In this study, the effects of Elasto-hydrodynamic lubrication pressure on the critical shoulder height of raceway in an angular contact ball bearing were investigated. Both 3D contact analyses using an influence function and the EHL analysis were conducted for the contact geometry between the ball and raceways. The pressure distributions by 3D contact analysis and EHL analysis for an example bearing were compared. The effect of ellipse truncation on the minimum film thickness also investigated from EHL analysis. The critical shoulder height in the dry contact and the EHL state were compared for various applied loads. It is shown that when the ellipse truncation occurs, the pressure spike for the EHL conjunction is higher than that for the dry contact, and its location moves more inward of the contact center. The steep pressure gradients would increase the flow rate, so in order to maintain flow continuity a significant reduction in film thickness and an abrupt rise in pressure occurs in the edge of shoulder. Significant reduction of the minimum film thickness occurs near the edge of shoulder. The critical shoulder heights in the EHL state are calculated as higher values compared with in the dry contact. This results shows that the determination of critical shoulder height by the EHL analysis is more proper.

• 한국기계가공학회지
• /
• 제3권2호
• /
• pp.86-94
• /
• 2004

The flash temperature distribution on the contact surfaces between cam and roller-follower mechanism was analysed numerically. The elasto-hydrodynamic lubrication pressure and film thickness were used to get the accurate analysis results. The temperature distribution was obtained by numerical integration by making use of Carslaw and Jaeger's formulation to the whole contact surfaces. The maximum flash temperature was increased with both the increasing slip ratio of the contact surface and increasing external load Profile of the temperature distribution was affected by the sliding velocity of the surface.

• Tribology and Lubricants
• /
• 제1권1호
• /
• pp.69-79
• /
• 1985

Planocentric gears 장치에서 내치차에 pin type의 치형을 사용하고 휠의 치형을 원호로 구성하였을 경우 치의 접촉특성을 탄성유역학적 윤활이론을 도입하여 해석 하였다. 윤활 특성을 개선하기 위하여 물림 위치(meshing position)에 의거한 설계 방법과 치의 모서리 부분 형상을 만곡되게 하는 치형 설계 방법을 제시하고 기존 설계에 의한 장치와 수치적으로 특성을 비교 하였다.

• KSTLE International Journal
• /
• 제5권1호
• /
• pp.14-22
• /
• 2004

The sub-surface stress field beneath the gear's contact surface caused by the surface pressure in lubricated condition is analyzed. To evaluate the influence of the clearances between a gear tooth and a pinion tooth on the stress field, two kinds of tooth profile models - conventional cylinder contact model and new numerical model - were chosen. Kinematics of the gear is taken into account to obtain the numerical model which is the accurate geometric clearances between a gear tooth and a pinion tooth. Transient elasto-hydrodynamic lubrication (EHL) analysis is performed to get the surface pressure. The sub-stress field is obtained by using Love's rectangular patch solution. The analysis results show that the sub-surface stress is quite dependent on both the surface pressures and the profile models. The maximum effective stress of the new model is lower than that of the old model. The depth where the maximum effective stress occurs in the new model is not proportional to the intensity of the external load.

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1355-1364
• /
• 1994

This paper analyzes the running mechanism of flexible and thin foil above rotating protrusion through a numerical simulation. The scope of analysis is confined to the phenomena of elastohy-drodynamic lubrication between the stationary and rotary drums with a running protrusion and thin foil. This mathematical model is based on the modified Reynolds equation and the equation of plate, considering the geometry of protrusion, running direction of protrusion, and the effect of geometric nonlinearity. Finite element method is adopted as a numerical simulation technique to solve the avobe coupled nonlinear equations. In numerical analysis, the effects of the scanning angle in Reynolds equation and the nonlinear term in plate equation are evaluated. Furthermore, the simulation is applied to the situation that thin foil is located in the entire drums (stationary and rotary drums).

• Journal of Mechanical Science and Technology
• /
• 제19권11호
• /
• pp.1967-1974
• /
• 2005

The subsurface stress field caused by both normal loads and tangential loads has been evaluated using the rectangular patch solution. The effect of tangential loading on the subsurface stress field has been investigated in detail for both the cylinder-on-cylinder contact and a spur gear teeth contact. For the cylinder-on-cylinder contact, the subsurface stress fields are moved more to the direction of tangential loads and the positions where the maximum stress occur are getting closer to the surface with the increasing tangential loads. The subsurface stress fields of the gear teeth contact are expanded more widely to the direction of tangential loads with the increasing tangential loads. The friction coefficient of a gear teeth contact is low because they are operated in a lubricated condition, and therefore surface tractions in the EHL condition hardly affect on the subsurface stress field.