• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.163-170
• /
• 2005

In this paper, the rock bolts, soil nails with filling grout and the micro-piling with injecting grout by pressure were applied for the stabilization of the cut slopes consisting of sedimentary rocks, igneous rocks and metamorphic rocks respectively. The field measurements and 3-D FEM analyses to find out mobilized tensile stresses of the grouted-reinforcing members installed in the drilled holes were executed on each site. With assuming the increments of the cohesive strength in the improved ground, the back analysis using direct calibration approach of changing the elastic modulus of the ground was used to find out the improved elastic modulus which yields the same tensile stresses from field measurements. The results of back analysis show that the elastic modulus of the improved ground were 4 to 6 times as large as the elastic modulus of original ground. Consequently, the design for slope reinforcement to be more rational, it is proposed that not only the improved cohesive strength is to be used in the incremental ranges on well-known previous proposed data, but also the increased elastic modulus which is about 5 times as large as the original elastic modulus is to be considered in design.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.1
• /
• pp.9-17
• /
• 2016

The elastic modulus of a 3D-printed Kelvin foam plate is investigated by measuring the acoustic wave velocity of 1 MHz ultrasound. An isotropic tetrakaidecahedron foam with 3 mm unit cell is designed and printed layer upon layer to fabricate a Kelvin foam plate of 14 mm thickness with a 3D CAD/printer using ABS plastic. The Kelvin foam plate is completely filled with paraffin wax for impedance matching, so that the acoustic wave may propagate through the porous foam plate. The acoustic wave velocity of the foam plate is measured using the time-of-flight (TOF) method and is used to calculate the elastic modulus of the Kelvin foam plate based on acousto-elasticity. Finite element method (FEM) and micromechanics is applied to the Kelvin foam plate to calculate the theoretical elastic modulus using a non-isotropic tetrakaidecahedron model. The predicted elastic modulus of the Kelvin foam plate from FEM and micromechanics model is similar, which is only 3-4% of the bulk material. The experimental value of the elastic modulus from the ultrasonic method is approximately twice as that of the numerical and theoretical methods because of the flexural deformation of the cell edges neglected in the ultrasonic method.

• Journal of the Korean Ceramic Society
• /
• v.37 no.6
• /
• pp.596-603
• /
• 2000

The hardness and elastic modulus of three bulk materials are computed from the load and displacement data which are measured during basic nanoindentation test and compared with values determined by independent means to assess the accuracy of the method. The results show that with this technique, modulus and hardness and elastic modulus profile through depth of silicon nitride and silicon oxynitride films. The results show that for silicon nitride film deposited on silicon, hardness and elastic modulus increase as the volume ratio of NH3 : SiH4, which had been used for deposition, increases up to 20.0; and for silicon oxynitride film on silicon, the hardness and elastic modulus profile changes distinctly as the relative amount of oxygen in deposition gas mixture changes.

• Structural Engineering and Mechanics
• /
• v.78 no.3
• /
• pp.281-296
• /
• 2021

This article analyzed the modulus degradation of concrete subjected to multi-level compressive cyclic loading. The evolution of secant elastic modulus is investigated based on measurements from top loading platen and LVDT in the middle part of concrete. The difference value of the two secant elastic moduli is reduced when close to failure and could be used as a fatigue failure precursor. The fatigue hardening is observed for concrete during cyclic loading. When the maximum stress is smaller the fatigue hardening is more obvious. The slight increase of maximum stress will lead to the "periodic hardening". The tangent elastic modulus shows a specific "bowknot" shape during cyclic loading, which can characterize the hysteresis of stress-strain and is influenced by the cyclic loading stresses. The deterioration of secant elastic modulus acts a similar role with respect to the P-wave speed during cyclic loading, can both characterize the degradation of the concrete properties.

• International Journal of Safety
• /
• v.11 no.1
• /
• pp.19-21
• /
• 2012

In this thesis, fracture test was performed in order to investigate the fracture strength of SFRC(steel fiber reinforced concrete) structures. The relationship between the compressive force and strain value of SFRC specimens were observed under the compressive strength test. From the fracture test results, the relationship between percentage of fiber by volume, compressive strength, elastic modulus, and tensile strength of SFRC beams were studied, and the measured elastic modulus of SFRC were compared with the calculated elastic modulus by ACI committee 544.

• Geomechanics and Engineering
• /
• v.28 no.1
• /
• pp.89-105
• /
• 2022

The behavior of the soil subgrade is complex and irregular against loads. When modeling, the soil is often replaced by a more straightforward system called a subgrade model. The Winkler method of linear elastic springs is a popular method of soil modeling in which the spring constant shows the modulus of subgrade reaction. In this research, the factors affecting the distribution of the modulus of subgrade reaction of elastoplastic subgrades are examined. For this purpose, critical theories about the modulus of subgrade reaction were examined. A square raft foundation on a sandy soil subgrade with was analyzed at different internal friction angles and Young's modulus values using ABAQUS software. To accurately model the actual soil behavior, the elastic, perfectly plastic constitutive model was applied to investigate a foundation on discrete springs. In order to increase the accuracy of soil modeling, equations have been proposed for the distribution of the subgrade reaction modulus. The constitutive model of the springs is elastic, perfectly plastic. It was observed that the modulus of subgrade reaction under an elastic load decreased when moving from the corner to the center of the foundation. For the ultimate load, the modulus of subgrade reaction increased as it moved from the corner to the center of the foundation.

• Journal of the Microelectronics and Packaging Society
• /
• v.21 no.4
• /
• pp.125-131
• /
• 2014

In order to develop stretchable substrates for wearable packaging applications, the variation behavior of elastic modulus was evaluated for transparent PDMS Sylgard 184 and black PDMS Sylgard 170 as a function of the base/curing agent mixing ratio. Both for Sylgard 184 and Sylgard 170, the true elastic modulus evaluated on a true stress-true strain curve was higher more than two times compared to the engineering elastic modulus obtained from an engineering stres-sengineering strain curve, and their difference became larger with increasing the stiffness of the PDMS. Sylgard 184 exhibited a maximum engineering elastic modulus of 1.74 MPa and a maximum true elastic modulus of 3.57 MPa at the base/curing agent mixing ratio of 10. A maximum engineering elastic modulus of 1.51 MPa and a maximum true elastic modulus of 3.64 MPa were obtained for Sylgard 170 at the base/curing agent mixing ratio of 2.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.10
• /
• pp.954-960
• /
• 2008

The effects of elastic modulus coefficient and linear expansion coefficient of overhead distribution power line(ACSR $58 mm^2$) on sag behavior in distribution line have been investigated to clarify the difference between specification and experimental level. The elastic modulus coefficients of Al wire and steel wire were $5,182.6 kgf/mm^2,\;18,348.8 kgf/mm^2$, respectively Therefore, the computational composition elastic modulus coefficient of the power line was $7,063.5 kgf/mm^2$, while that of experimentally measured was $7681.1 kgf/mm^2$. As a result, we found that elastic modulus coefficient which was experimentally measured was higher than that of computational by 8.7 %. However, when planner designs the sag of disoibution line, the elastic modulus coefficient of power line $8,400 kgf/mm^2$ should be generally adopted. These two different using values lead to the sag difference of 0.62 m. The other results will be discussed.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.37-42
• /
• 2001

This paper presents the improved elastic modulus equation more appropriate to predict the modulus of elasticity of structural elements designed and made by high-strength concrete. To propose the elastic modulus equation, more than 300 laboratory specimen tests having the range of 5n to 800kgf/$cm^{2}$ in concrete compressive strength were conducted and analyzed statistically. The equation derived in terms of empirical constant, the elastic moduli of coarse aggregate and mix proportions. Comparison of the proposed elastic modulus equation with the previously suggested equations in the ACI363R, and New-RC were also presented to demonstrate the applicability to practice.

• Journal of Mechanical Science and Technology
• /
• v.17 no.12
• /
• pp.1928-1937
• /
• 2003

Effect of elastic modulus mismatch on the contact crack initiation is investigated to find major parameters in designing desirable surface-coated system. Silicon nitride coated soft materials with various elastic modulus mismatch, E$\_$c//E$\_$s/＝1.06∼356 are prepared for the analysis. Hertzian contact test is conducted for producing contact cracks and the acoustic emission detecting technique for measuring the critical load of crack initiation. The implication is that coating thickness and material strength are controllable parameters to prevent the initiation of contact cracks resulted from the elastic modulus mismatch in the hard ceramic coating layer on the soft materials.