• Korean Journal of Materials Research
• /
• v.4 no.7
• /
• pp.792-797
• /
• 1994

Force fields of syndiotactic isoregic PVF crystal have been extracted by optimizing a structure of 2,4,6-trifluoroheptane with ab initio Quantum mechanical method with 6-31G * * basis set, and applied to calculate the structure parameters and elastic constants of the material. The cell parameters turned out to be 5.205$\AA$, of a axis(chain axis), 8.457$\AA$, of b axis and 4.621$\AA$ of c axis. These parameters are in fair agreement with those of the atactic X-ray structure(5.04$\AA$, 8.57$\AA$, and 4.95$\AA$,respectively). The young's modulus of defect free syndiotactic PVF crystal was computed to be 267 GPa comparable to those of polyvinilidene fluoride(277-293 GPa) and polyethylene(264-337 GPa) crystals. Bulk modulus value obtained at optimum geometry is more than twice greater than that obtained at experimental geometry due to large difference of elastic compliance constant (especially Sgj element) at these two different geometries.

• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.1042-1049
• /
• 2007

Recently, a theoretically-sound design approach, using an elastic multilayer model, is attempted in trackbed designs for the construction of high speed railways and new lines of conventional railways. In the elastic multilayer model, the stress-dependent resilient modulus($E_R$) is an important input parameter, that is, reflects substructure performance under repeated traffic loading. However, the evaluation method for resilient modulus using repeated loading triaxial test is not fully developed for practical purpose, because of costly equipment and the significantly fluctuated values depending on the testing equipment and laboratory personnel. In this study, the paper will present an indirect method to estimate the resilient modulus using dynamic properties. The resilient modulus of crushed stone, which is the typical material of sub-ballast, was calculated with the measured dynamic properties and the range of stress level of the sub-ballast, and approximated with the power model combined with bulk and deviatoric stresses. The resilient modulus of coarse grained material decreases with increasing deviatoric stress at a confining pressure, and increases with increasing bulk stress. Sandy soil(SM classified from Unified Soil Classification System) of subgrade was also evaluated and best fitted with the power model of deviatoric stress only.

• Structural Engineering and Mechanics
• /
• v.47 no.6
• /
• pp.839-856
• /
• 2013

Metallic annular discs with their outer boundary fully constrained are studied with newly derived semi-analytical solutions for the effects of thickness variations under thermal loading and unloading. The plane stress and axisymmetric assumptions were adopted, and the thickness of the disk depends on the radius hyperbolically with an exponent n. Furthermore, it is assumed that the stress state is two dimensional and temperature is uniform in the domain. The solutions include the elastic, elastic-plastic and plastic-collapse behavior, depending on the values of temperature. The von Mises type yield criterion is adopted in this work. The material properties, Young's modulus, yield stress and thermal expansion coefficient, are assumed temperature dependent, while the Poisson's ratio is assumed to be temperature independent. It is found that for any n values, if the normalized hole radius a greater than 0.6, the normalized temperature difference between the elastically reversible temperature and plastic collapse temperature is a monotonically decreasing function of inner radius. For small holes, the n values have strong effects on the normalized temperature difference. Furthermore, it is shown that thickness variations may have stronger effects on the strain distributions when temperature-dependent material properties are considered.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.13-19
• /
• 2008

A Wire-woven Bulk Kagome (WBK) is the new truss type cellular metal fabricated by assembling the helical wires in six directions. The WBK seems to be promising with respect to morphology, fabrication cost, and raw materials. In this paper, first, the geometric and material properties are defined as the main design parameters of the WBK considering the fact that the failure of WBK is caused by buckling of truss elements. Taguchi approach was used as statistical design of experiment(DOE) technique for optimizing the design parameters in terms of maximizing the compressive strength. Normalized specific strength is constant regardless of slenderness ratio even if material properties changed, while it increases gradually as the strainhardening coefficient decreases. Compressive strength of WBK dominantly depends on the slenderness ratio rather than one of the wire diameter, the strut length. Specifically the failure of WBK under compression by elastic buckling of struts mainly depended on the slenderness ratio and elastic modulus. However the failure of WBK by plastic failed marginally depended on the slenderness ratio, yield stress, hardening and filler metal area.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.1031-1036
• /
• 2000

In this study, a numerical simulation that can effectively predict the strengthening effect of repaired aged RC structures is developed using the axial deformation link elements. In repaired structures, concrete and interface are modeled as quasi-brittle materials. An elastic-perfectly plastic constitutive relationship is introduced for reinforcing bars. Also, a linear-elastic relationship for repair materials such as FRP or CFS. Structural deterioration in terms of corrosion of steel rebar is considered. The interfacial property between steel and concrete which is reduced by corrosion of steel rebar is obtained by comparing numerical results with experimental results of pull out tests. Obtained values are used in repaired reinforced concrete structures under flexural loading conditions. To investigate strengthening effect of the structures repaired with carbon fiber sheet(CFS), repaired and unrepaired RC structures are analyzed numerically. From analysis, rip-off, debonding and rupture failure mechanisms of interface between substrate and CFS can be determined. Finally, strengthening effect according to the variation of interfacial material properties is investigated, and it is shown that interfacial material properties have influence on the mechanical behavior of repaired structure systems Therefore, the developed numerical method using axial deformation link elements can use for determining the strengthening effects and failure mechanism of repaired aged RC structure.

• Smart Structures and Systems
• /
• v.9 no.2
• /
• pp.127-143
• /
• 2012

The present paper deals with the nonlinear analysis of the functionally graded piezoelectric (FGP) annular plate with two smart layers as sensor and actuator. The normal pressure is applied on the plate. The geometric nonlinearity is considered in the strain-displacement equations based on Von-Karman assumption. The problem is symmetric due to symmetric loading, boundary conditions and material properties. The radial and transverse displacements are supposed as two dominant components of displacement. The constitutive equations are derived for two sections of the plate, individually. Total energy of the system is evaluated for elastic solid and piezoelectric sections in terms of two components of displacement and electric potential. The response of the system can be obtained using minimization of the energy of system with respect to amplitude of displacements and electric potential. The distribution of all material properties is considered as power function along the thickness direction. Displacement-load and electric potential-load curves verify the nonlinearity nature of the problem. The response of the linear analysis is investigated and compared with those results obtained using the nonlinear analysis. This comparison justifies the necessity of a nonlinear analysis. The distribution of the displacements and electric potential in terms of non homogenous index indicates that these curves converge for small value of piezoelectric thickness with respect to elastic solid thickness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.233-233
• /
• 2008

A piezoelectric ultrasonic linear motor shaped with 'Butterfly' wings has been developed for thin electronics such as cellular phone and PDA. The butterfly piezoelectric transducer is simply composed of an elastic plate, which includes a tip for energy transfer and two protrusions to fix it, and two piezoelectric ceramics. Contact materials, such as a brass, and steel and alumina can make it possible to improve dynamic properties of the motors over a wide range of tribological conditions. The dynamic properties of the motor have been intensively measured and analyzed according to the applied voltage wave forms at the various frequencies. The results of numerical study and experimental investigation will be used for the future optimization of the actuator and the realization of the advanced ultrasonic motor.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1479-1489
• /
• 1995

In this study, tensile strength and modulus were evaluated for a filament wound ring specimen by split disk test and compared with the theoretical values obtained by the rule of mixtures. The circumferentially wound ring specimens were prepared from 4 types of material systems. The results showed that the measured strengths of the composite systems were considerably lower than the theoretical values due to the local bending stresses around the split disk edges. for the measurement of elastic moduli of the filament wound ring specimens, the effect of friction on the strain of the ring must be taken into account. But the effect of friction between the split disk fixture and the ring specimen can be eliminated by averaging the moduli for loading and unloading state with maintaining the same crosshead rates. The measured elastic moduli of ring specimens showed very good agreement with the theoretical values.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.10 s.175
• /
• pp.167-173
• /
• 2005

The Berkovich nano-indentation is an indentation test method analyzing mechanical properties of materials such as hardness and elastic modulus. The length scale of the penetration is measured in nanometers. Therefore, this method becomes widely useful for analyzing the mechanical property of thin film which can not be measured before. In this paper, comparing two results of the load-displacement curve obtained by the Berkovich nano-indentation and the 3-D finite element analysis, it was confirmed that the 3-D finite element analysis is useful. The phenomenon of pile-up and sink-in due to material properties was discussed by the finite element analysis.

• Proceedings of the Computational Structural Engineering Institute Conference
• /
• 2010.04a
• /
• pp.268-271
• /
• 2010

In this paper, forward and reverse analysis is introduced in order to estimate the elastic-plastic properties from a power-law hardening bulk specimen materials with one simple spherical indentation impression test. In order to verify the reliability of the reverse analysis, we have simulated about a large range of materials that essentially cover all engineering materials, using ABAQUS(6.91) program. Then, we could obtained the fitting functions and plastic parameters from the numerical analysis results. Next, through the procedure of reverse analysis we can obtain the yield stress and power-law exponent. Finally, obtain good agreement between the result from reverse analysis and initial input data from experiment.