• 한국폐기물자원순환학회지
• /
• 제35권7호
• /
• pp.600-605
• /
• 2018

In this study, the combustion characteristics were investigated based on the biodrying solid recovered fuel (SRF) in a 5 Ton/day scale combustion boiler. The composition of the combustion gas containing the biodrying SRF was analyzed, the particulate matter, and its HCl content was determined with the air pollutant process test method. Mass balance, carbon balance, and combustion efficiency were calculated according to the equivalence ratio (ER) method; the energy recovery efficiency of the combustion boiler was also analyzed. The overall combustion efficiency of the biodrying SRF was 97.3 % and the energy recovery efficiency was 80.2%.

• 전기학회논문지
• /
• 제62권11호
• /
• pp.1566-1570
• /
• 2013

In this paper, we analyzed the electric characteristics of the OLEDs device of which anode ITO has been treated with the oxygen plasma. We fabricated the basic three-layer structure (ITO / AF / $Alq_3$ / $Cs_2CO_3$ / Al) device, analyzed how the oxygen plasma treatments of the ITO surface affects to the electrical characteristics of OLEDs. We also produced a four-layer structure device (ITO / AF / TPD / $Alq_3$ / $Cs_2CO_3$ / Al) with the oxygen plasma treatment. From the comparative analysis to the devices, we confirmed following results. The three-layer structure OLEDs device with oxygen plasma treatment has better characteristics than the device without the treatments; maximum luminance, luminous efficiency, and external quantum efficiency are improved approximately 151 [%], 126 [%], and 175[%], respectively. Also, the electric characteristics of the four-layer structure device with oxygen plasma treatment are improved comparing to the characteristics of the three-layer structure device with oxygen plasma treatment; maximum luminance, luminous efficiency, and external quantum efficiency are improved approximately 144 [%], 115 [%], and 124[%], respectively.

• 한국분무공학회지
• /
• 제11권4호
• /
• pp.220-227
• /
• 2006

Experimental studies has been conducted to investigate the effect of orifice diameter ratio on the mixing characteristics of the split element of doublet and triplet elements. The spray characteristics of non-reacting immiscible liquids have been investigated using a patternator. The local volume fraction is measured by use of mean value of each component. This volume measurement represents the mixing characteristics of the liquid, which affect the overall combustion efficiency. The ratio of the orifice diameter, ranging from 1 to 1.5, and that of the jet-momentum, ranging from 0.5 to 6.0, we used. The jet impinging behavior with use of various ratios exhibits substantially different mixing characteristics. Mixing efficiency is maximized when the jet-momentum ratio is increased; this behavior is particularly prominent when the orifice diameter ratio is greater than unity. The split of the triplet element yields better mixing characteristics and is more effective than that of the doublet element in regard to achieving high combustion efficiency. The optimum mixing factor for the triplet element is found to be 0.75, according to our measurement.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.516-521
• /
• 2001

Present study deals with combustion characteristics and performance of U type radiation tube burner with fin which combustion capacity is 30,000kcal/hr and the maximum capacity of supply fuel is $30Nm^{3}/hr$. Temperature difference of radiation tube is about $173^{\circ}C$ at 25% capacity and this show relatively small temperature difference for convenient type. Thermal efficiency is satisfactory as $72{\sim}81%$. Also, radiative efficiency of radiation tube is $52{\sim}73%$. The efficiency of heat exchanger is $27{\sim}37%$. Therefore, radiative efficiency is improved to $1{\sim}10%$ after installing fin.

• 조명전기설비학회논문지
• /
• 제26권8호
• /
• pp.18-26
• /
• 2012

Recently, there have been suggestions that power factor should be considered to increase the efficiency of electric power supply when evaluating the performance of the electric appliances in standby mode and the related studies have been conducted to improve the efficiency standard of standby power. But, they lack the analysis of the standby power characteristics with the changes of power factor. This study is conducted to analyze the standby power characteristics of TV which is a typical home appliance and reaches a conclusion that the apparent power can be a more reasonable index which reflects the efficiency of electric power supply. It is also found that LED TVs show the best performance in standby mode. Moreover, an example to set standby power standards on TVs to be applied in the future is suggested, considering the energy efficiency policies for appliances.

• 전기학회논문지
• /
• 제60권7호
• /
• pp.1366-1371
• /
• 2011

The resonant converter cause the high voltage stress according to the input voltage, which increases the conduction loss in converter power switches. The topology of LLC half bridge resonant converter provides ZVS characteristic and also the stress of voltage and current is smaller than that of the general resonant converters. So we can expect the higher efficiency. In this paper, the analysis of the characteristics of the converter efficiency and the best conditions for highest efficiency were investigated. As a result, the efficiency of utilizing up to 93% is achieved.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2005년도 하계학술대회 논문집 Vol.6
• /
• pp.537-538
• /
• 2005

A way of measuring an efficiency of organic light-emitting diodes are studied. The efficiency is obtained from the current-voltage-luminance characteristics of the devices. Basically, number of charge carriers are obtained from the current-voltage characteristics, and the number of photons are obtained from the current of Si-photodetector. The organic light-emitting diodes are assumed as a lambertian light source and a program is made for calculating the efficiency. A device structure of ITO/TPD/$Alq_3$/Al is manufactured using thermal-vapor evaporation. This device is set into a measuring system and measured the efficiency. The efficiencies are measured using the lab-made program and commercially available equipments. The obtained values are similar to each other within 10% uncertainty.

• 한국유기농업학회지
• /
• 제24권3호
• /
• pp.385-412
• /
• 2016

This paper analyzes economic efficiency of strawberries and tomatoes farms using the data envelopment analysis (DEA). We examine how production characteristics and farm size affect overall efficiency (OE), allocative efficiency (AE), and technological efficiency (TE). We also survey sample farm households from the Farm Income Investigation database of Rural Development Administration to investigate management and cultivation techniques and to analyze economic efficiency by technique. Implications for improving efficiency are suggested in the conclusion.

• 한국정밀공학회지
• /
• 제17권4호
• /
• pp.48-68
• /
• 2000

The high-speed machining technology of difficult-to-cut material is needed to achieve the high-efficiency of die manufacturing. The high-speed machining is applied in automobile, airplane and electricityㆍelectro industry etc, because it can improve machining efficiency and productivity with high speed, high power and high rotation. In this study, high speed machinability, tool wear characteristics and its monitoring, characteristics of damaged layer, machinability of difficult-to-cut material, characteristics of a free curved surface and method of CAD/CAM system were introduced to acquire the shortening of machining time, the improvement of machining efficiency and the high quality of machined surface. Therefore, we establish the stabilization condition of difficult-to-cut material machining and present the optimal cutting condition for high-efficiency cutting.

• 한국군사과학기술학회지
• /
• 제5권4호
• /
• pp.9-18
• /
• 2002

In this paper, we have studied the characteristics of a perforated muzzle brake. The main purpose of a muzzle brake is to reduce the momentum being applied to the recoil system. Muzzle brake redirect a portion of the exiting gases to the side exerting a forward force on the brake, thus reducing recoil. So it also reduces the recoil force which acts on the turret and vehicle. First of all, we analyzed the flow-field characteristics of muzzle brake using RAMPANT software. Then we investigated the influence of design parameters of perforated muzzle brake. Sixteen muzzle brakes were tested and evaluated for analyzing their influence on the muzzle brake efficiency. The muzzle brakes were designed to fit on a 40mm gun barrel. The strong dependent parameters of muzzle brake efficiency were the wall thickness(L/d ratio) and the area ratio AR. We designed the perforated muzzle brakes which have 10-20% efficiency. And we proposed a design method of perforated muzzle brake.