• Korean Journal of Environmental Agriculture
• /
• v.27 no.1
• /
• pp.60-65
• /
• 2008

Current soil remediation principles for toxic metals have some limitations even though they vary with different technologies. An alternative technology that transforms hazardous substances into nonhazardous ones would be environmentally beneficial. Objective of this research was to assess optimum conditions for Cr(VI) reduction in soils as influenced by ZVI(Zero-Valent Iron), organic matter and moisture content. The reduction ratio of Cr(VI) was increased from 37 to 40% as organic matter content increased from 1.07 to 1.75%. In addition, Cr(VI) concentration was reduced as soil moisture content increased, but the direct effect of soil moisture content on Cr(VI) reduction was less than 5% of the Cr(VI) reduction ratio. However, combined treatment of ZVI(5%), organic matter(1.75%) and soil moisture(30%) effectively reduced the initial Cr(VI) to over 95% within 5 days and nearly 100% after 30 days by increasing oxidation of ZVI and concurrent reduction of Cr(VI) to Cr(III). The overall results demonstrated that ZVI was effective in remediating Cr(VI) contaminated soils, and the efficiency was synergistic with the combined treatments of soil moisture and organic matter.

• The Journal of Korean Society for Radiation Therapy
• /
• v.16 no.2
• /
• pp.19-24
• /
• 2004

Introduction : The Vaginal, the urethra, the vulva and anal cancer avoid the many dose to femur head and the additional treatment is necessary in inguinal LN. The partial transmission block to use inguinal LN addition there is to a method which it treats and produce partial transmission block a method and the MLC which to it analyzes. Material & Methode : The Inguinal the LN treatment patient partial transmission it used block and the MLC in the object and with solid water phantom with the patient it reappeared the same depth. In order to analyze the error of the junction the EDR2 (Extended dose range, the Kodak and the U.S) it used the Film and it got film scanner it got the beam profile. The partial transmission block and the MLC bias characteristic, accuracy and stability of production for, it shared at hour and comparison it analyzed. Result : The partial the transmission block compares in the MLC and the block production is difficult and production hour also above 1 hours. The custom the block the place where it revises the error of the junction is a difficult problem. If use of the MLC the fabrication will be break and only the periodical calibration of the MLC it will do and it will be able to use easily. Conclusion : The Inguinal there is to LN treatment and partial transmission block and the MLC there is efficiency of each one but there is a place where the junction of block for partial transmission block the production hour is caught long and it fixes and a point where the control of the block is difficult. like this problem it transfers with the MLC and if it treats, it means the effective treatment will be possible.

• International Journal of Highway Engineering
• /
• v.11 no.4
• /
• pp.69-78
• /
• 2009

Korea has achieved significant economic growth with building the Gyeongbu Expressway. As the number of new road construction projects has decreased, it becomes more important to maintain optimal status of the current road networks. One of the best ways to accomplish it is weight enforcement as active control measure of traffic load. This study is to develop High-speed Weigh-in-motion System in order to enhance efficiency of weight enforcement, and to analyze patterns of overloaded trucks on highways through the system. Furthermore, it is to review possibilities of developing overweight control system with application of the HS-WIM system. The HS-WIM system developed by this study consists of two sets of an axle load sensor, a loop sensor and a wandering sensor on each lane. A wandering sensor detects whether a travelling vehicle is off the lane or not with the function of checking the location of tire imprint. The sensor of the WIM system has better function of classifying types of vehicles than other existing systems by detecting wheel distance and tire type such as single or dual tire. As a result, its measurement errors regarding 12 types of vehicle classification are very low, which is an advantage of the sensor. The verification tests of the system under all conditions showed that the mean measurement errors of axle weight and gross axle weight were within 15 percent and 7 percent respectively. According to the WIM rate standard of the COST-323, the WIM system of this study is ranked at B(10). It means the system is appropriate for the purpose of design, maintenance and valuation of road infrastructure. The WIM system in testing a 5-axle cargo truck, the most frequently overloaded vehicle among 12 types of vehicles, is ranked at A(5) which means the system is available to control overloaded vehicles. In this case, the measurement errors of axle load and gross axle load were within 8 percent and 5 percent respectively. Weight analysis of all types of vehicles on highways showed that the most frequently overloaded vehicles were type 5, 6, 7 and 12 among 12 vehicle types. As a result, it is necessary to use more effective overweight enforcement system for vehicles which are seriously overloaded due to their lift axles. Traffic volume data depending upon vehicle types is basic information for road design and construction, maintenance, analysis of traffic flow, road policies as well as research.

• Korean Journal of Medicinal Crop Science
• /
• v.4 no.1
• /
• pp.78-85
• /
• 1996

The effects of growth regulators, sucrose and gelling agents were investigated to increase the efficiency of the callus growth and plant regenerarion in tissue culture of Angelica koreana Max. The fresh weight and dry weight of subcultured callus was highest in MS medium supplemented with 1 mg/l 2,4-D. Callus growth was excellent in 2% sucrose, but it was inhibited in propotion to sucrose content. Effect of gelling agents on callus growth was highest on 1.2% agar and 0.4% Gelrite medium, respectively. The browning of callus was protected on the media supplemented with 10 mg/l ABA and 5 or 10 mg/l $AgNO_3$. In the callus induction and growth from the peduncle of immature inflorescence, 2,4-D was more effective than NAA, and the frequency of callus induction was highest as 81.7% in 2 mg/l 2,4-D. Plant was not regenerated from the callus derived from young leaf. Somatic embryos were developed from the surface of callus drived from the peduncle of immature inflorescence in the medium containing 0.5 mg/l 2,4-D, 1 mg/l kinetin, 5 mg/l ABA and 5 mg/l $AgNO_3$. Plants were developed from the matured somatic embryos in the medium supplemented with 0.2 mg/l 2,4-D and 1 mg/l kinetin.

• Journal of Life Science
• /
• v.26 no.2
• /
• pp.190-197
• /
• 2016

Aflatoxin M₁ can be produced in cow’s milk when cows eat contaminated produce. Milk is a major source of food for infants and for children who have a weak level of immunity, and the detection of Aflatoxin M₁ for risk assessment is necessary in order to reduce the amount of it in milk. In this study, the Aflatoxin M₁ level was monitored for one year in raw milk samples obtained from Chungnam Province, Korea. The milk samples were divided into three categories: 1. milk samples from a standard general farm, 2. milk samples from a HACCP controlled farm, and 3. milk samples from the supply of Aflatoxin M₁ reduced fodder. The average concentrations of Aflatoxin M₁ in milk were 0.023±0.005 ug/l for the standard general farm, 0.017±0.004 ug/l for the HACCP controlled farm, and 0.013±0.003 ug/l for the supply of Aflatoxin M₁ reduction fodder. Milk collected from the supply of Aflatoxin M₁ reduction fodder had the lowest level of Aflatoxin M₁. However, when efficiency and economic aspects are considered the most effective way of reducting Aflatoxin M₁, could be taking milk from the HACCP controlled farm and implementing good feed management. Institutional support from the government, careful management of dairy farming, and a strict farm sanitation program are required in order to lower the level of Aflatoxin M₁ in milk.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.12 no.3
• /
• pp.125-132
• /
• 2007

We estimated the distribution of predator-prey interaction strengths for 12 species of herbivores (including amphipods, isopods, gastropods, and sea urchins) and made a regression model that may be applicable to other species. Laboratory experiments were used to determine per capita grazing rate (PCGR; g seaweeds/individual/day). Relationship between the biomass of individual grazers and fourth-root transformed PCGR was fitted to power curve ($y=0.2310x^{0.3290}$, r=0.8864). This finding supported that the grazing efficiency was not even as individual grazers increase in size (biomass). Therefore, the biomass-normalized PCGR was estimated and revealed that smaller size herbivores were more effective grazers. Grazing impact considering density of each taxon was calculated. The sea hare Aplysia kurodai had greatest grazing impact on the seaweed bed and the sea urchin Strongylocentrotus nudus and S. intermedius were ranked in descending order of the impact. The amount of seaweed grazed by the amphipod Elasmopus sp. (>4,000 $ind./m^2$) and Jassa falcata (>2,000 $ind./m^2$) were 3.435 and $1.697mg/m^2/day$ respectively. The combined grazing amount of herbivores was $5,045mg/m^2/day$ in the seaweed bed. Although sea hare and sea urchin had strong impacts on seaweeds, the effects of dense, smaller species could not be seen as negligible. Surprisingly, the calculated grazing potential of sea urchins with a mean density of 3 $ind./m^2$ exceeded the mean production of seaweed cultured in domestic coastal waters in Korea (ca., 5 ton/ha). Small crustaceans were also expected to consume up to 16% of the seaweed production if their densities were rising under weak predation conditions. Considering that the population density of herbivores are strongly controlled by fish, human interference like overfishing may have strong negative effects on persistence of seaweeds communities.

• Horticultural Science & Technology
• /
• v.28 no.3
• /
• pp.403-408
• /
• 2010

This study was carried out to investigate the physiological responses of $Rhododendron$ $mucronulatum$ Turcz. and $R.$ $indicum$ (L.) Sweet seedlings with 0%, 35%, 55% and 75% shading of full sunlight in polyethylene film house. The shading treatments were performed during the late growth season for each species (from Sept. 9 to Nov. 5, 2008). The shading treatment was effective in reducing the daily temperature by 0.9 to $1.7^{\circ}C$ during September and by 0.8 to $1.7^{\circ}C$ during October. Before the shading treatments, the water content of $R.$ $mucronulatum$ and $R.$ $indicum$ amounted to 68.5% and 66.3%, respectively. The water contents of two species after 75% shading treatment period decreased to 66.2% (3.4% reduction) and 65.9% (0.6% reduction), respectively. Notably, both species had a similar tendency indicating less reduction rate of water content with 75% shading. $R.$ $indicum$ showed higher photosynthetic capacity with higher level of shading, and its photosynthetic capacity reached the highest level ($9.63{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$). On the other hand, shading-treated $R.$ $indicum$ showed higher intercellular $CO_2$ concentration, stomatal conductance and transpiration rate (55% shading > 35% shading > 75% shading) than non-treated ones. In addition, non-treated seedlings showed higher water use efficiency than treated ones. In particular, it was found that the leaf color of $R.$ $mucronulatum$ turned equivalent to purple under full sunlight, while its leaf color kept equivalent more to green with higher level of shading, as evidenced even in naked eyes. According to comprehensive analysis using Munsell Color Chart on potential leaf color variations of $R.$ $mucronulatum$ depending on the level of shading, it was found that relatively many leaf colors under full sunlight were equivalent to R (red) and Y (yellow) chart, while relatively many leaf colors with higher level of shading were equivalent to G (green) and Y chart, where the latter still showed green color.

• Journal of Internet Computing and Services
• /
• v.16 no.5
• /
• pp.29-38
• /
• 2015

The Energy Storage System stores electricity for later use. This system can store electricity from legacy electric power systems or renewable energy systems into a battery device when demand is low. When there is high electricity demand, it uses the electricity previously stored and enables efficient energy usage and stable operation of the electric power system. It increases the energy usage efficiency, stabilizes the power supply system, and increases the utilization of renewable energy. The recent increase in the global interest for efficient energy consumption has increased the need for an energy storage system that can satisfy both the consumers' demand for stable power supply and the suppliers' demand for power demand normalization. In general, an energy storage system consists of a Power Conditioning System, a Battery Management System, a battery cell and peripheral devices. The specifications of the subsystems that form the energy storage system are manufacturer dependent. Since the core component interfaces are not standardized, there are difficulties in forming and operating the energy storage system. In this paper, the design of the profile structure for energy storage system and realization of private profiling system for energy storage system is presented. The profiling system accommodates diverse component settings that are manufacturer dependent and information needed for effective operation. The settings and operation information of various PCSs, BMSs, battery cells, and other peripheral device are analyzed to define profile specification and structure. A profile adapter software that can be applied to energy storage system is designed and implemented. The profiles for energy storage system generated by the profile authoring tool consist of a settings profile and operation profile. Setting profile consists of configuration information for energy device what composes energy saving system. To be more specific, setting profile has three parts of category as information for electric control module, sub system, and interface for communication between electric devices. Operation profile includes information in relation to the method in which controls Energy Storage system. The profiles are based on standard XML specification to accommodate future extensions. The profile system has been verified by applying it to an energy storage system and testing charge and discharge operations.

• Asian Journal of Business Environment
• /
• v.2 no.1
• /
• pp.25-34
• /
• 2012

It is possible to use pallet for forwarding as chinese cabbages and radishes are general large-scale trading items at the agricultural wholesale market though, however, most of these are forwarded as it have packed in net bags or in P·E bags. Thus, it is still hard for palletizing. The type of packing the product in the net bag makes it difficult for palletizing. It is not a stable shape enough and easily collapsed for pallet loading. Because of this collapsibility, the corrugated cardboard box is being used to enhance forwarding efficiency, but the existing corrugated cardboard box could be crushed easily by moist what is from the agricultural product's property and it also could be squashed by the mass of the loaded box layers on itself. In contrary, the functional waterproof corrugated cardboard box is not collapsed through palletizing and it is efficient for product management with it's ventilation function in respond to pre-cooling effect. Furthermore, because it has various functional shapes as the open type, the partition type and so on, it is effective for maintaining freshness of the product and standardizing the distribution of agricultural product. It is well-known that it is possible to introduce this box to cargo-works of agricultural product. Consequently, the recognition of main distributors about the pallet distribution of the chinese cabbage and the radish was apprehended in this study for activating mechanization of loading and unloading. The survey was conducted to the main distributors such as the forwarder, the auction dealer and the commission merchant with Garak-dong wholesale market as the center. The appropriate packing materials and problems of the existing method for loading and unloading were derived through the survey. Especially, it was focused on analyzing the difference of recognition between the subject groups for the way of using waterproof cardboard corrugated box to deal with the difficult product for packing in normal corrugated box because of the box's absorption of moist from the agricultural product like a chinese cabbage and a radish. Total In the cases of the forwarders and the commission merchants, the net was highly responded as 45%, 74% from each groups for the best packing material for mechanization of distribution and the waterproof corrugated cardboard box was responded as 20%, 22% from each groups as much preferable than multi-stage wooden box. However, for the radish, the waterproof corrugated cardboard box was the best material as 56%, and the auction trader group supported it for 80%. So, the using the waterproof corrugated cardboard box for mechanization of distribution was negative for the chinese cabbage, but it was positive for the radish. The average was 2.42, the standard deviation was 1.24. The negative response(about 55%) was prevailing more than positive response(about 23%). It could be analyzed that even there was the positive recognition for using the waterproof corrugated cardboard box for the radish though the preference for low price of net bag in the chinese cabbage forwarding procedure. Still now, it seems that is a burden for using the waterproof corrugated cardboard box with high price. In the analysis on the recognition differences about using the waterproof corrugated cardboard box for the chinese cabbages and the radish between the forwarders and the commission merchants, generally the negative recognition was prevailing, but the forwarders(2.696) were more positive for using the waterproof corrugated cardboard box than the commission merchants(2.145).

• Journal of Distribution Science
• /
• v.9 no.3
• /
• pp.83-94
• /
• 2011

Most domestic companies, with the exclusion of major firms, are reluctant to implement a supply chain management (SCM) network into their operations. Most small- and medium-sized enterprises are not even aware of SCM. Due to the inherent total-systems efficiency of SCM, it coordinates domestic manufacturers, subcontractors, distributors, and physical distributors and cuts down on cost of inventory control, as well as demand management. Furthermore, a lack of SCM causes a decrease in competitiveness for domestic companies. The reason lies in the fundamentality of SCM, which is the characteristic of information sharing, process innovation throughout SCM, and the vast range of problems the SCM management tool is able to address. This study suggests the contemplation and reformation of the current SCM situation by analyzing the SCM strategic plan, discourses and logical discussions on the topic, and a successful case for adapting SCM; hence, the study plans to productively "process" SCM. First, it is necessary to contemplate the theoretical background of SCM before discussing how to successfully process SCM. I will describe the concept and background of SCM in Chapter 2, with a definition of SCM, types of SCM promotional activities, fields of SCM, necessity of applying SCM, and the effects of SCM. All of the defects in currently processing SCM will be introduced in Chapter 3. Discussion items include the following: the Bullwhip Effect; the breakdown in supply chain and sales networks due to e-business; the issue that even though the key to a successful SCM is cooperation between the production and distribution company, during the process of SCM, the companies, many times, put their profits first, resulting in a possible defect in demands estimation. Furthermore, the problems of processing SCM in a domestic distribution-production company concern Information Technology; for example, the new system introduced to the company is not compatible with the pre-existing document architecture. Second, for effective management, distribution and production companies should cooperate and enhance their partnership in the aspect of the corporation; however, in reality, this seldom occurs. Third, in the aspect of the work process, introducing SCM could provoke corporations during the integration of the distribution-production process. Fourth, to increase the achievement of the SCM strategy process, they need to set up a cross-functional team; however, many times, business partners lack the cooperation and business-information sharing tools necessary to effect the transition to SCM. Chapter 4 will address an SCM strategic plan and a case study of LG Electronics. The purpose of the strategic plan, strategic plans for types of business, adopting SCM in a distribution company, and the global supply chain process of LG Electronics will be introduced. The conclusion of the study is located in Chapter 5, which addresses the issue of the fierce competition that companies currently face in the global market environment and their increased investment in SCM, in order to better cope with short product life cycle and high customer expectations. The SCM management system has evolved through the adaptation of improved information, communication, and transportation technologies; now, it demands the utilization of various strategic resources. The introduction of SCM provides benefits to the management of a network of interconnected businesses by securing customer loyalty with cost and time savings, derived through the consolidation of many distribution systems; additionally, SCM helps enterprises form a wide range of marketing strategies. Thus, we could conclude that not only the distributors but all types of businesses should adopt the systems approach to supply chain strategies. SCM deals with the basic stream of distribution and increases the value of a company by replacing physical distribution with information. By the company obtaining and sharing ready information, it is able to create customer satisfaction at the end point of delivery to the consumer.