• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.833-838
• /
• 2001

The objectives of this study are to investigate effective stiffness of circular reinforced bridge columns and to provide reasonable effective stiffness equations for seismic design to the current Korean Bridge Design Standard. The material nonlinear analysis was conducted for 5184 columns of which variables were the concrete compressive stress, the steel yielding stress, the longitudinal steel location parameter, the longitudinal steel ratio, the axial load level, and the diameter of section. The current Korean Bridge Design Standard generally used the gross section stiffness because of unclear provision, it may be non-conservative because of being evaluated greater design seismic force and less design displacement than those of the abroad provision. Therefore, the proposed effective stiffness equations include three variables such as : the longitudinal steel location parameter, the longitudinal steel ratio, and the axial load ratio. Two equations of effective stiffness are proposed which may be used for earthquake force estimation and for earthquake displacement estimation, respectively.

• 한국강구조학회 논문집
• /
• 제29권3호
• /
• pp.229-236
• /
• 2017

이 연구에서는 고무스프링의 동적 압축실험을 수행하여 고무스프링의 거동 및 특성을 규명하고 압축 강성도를 계산하여 실제 설계값에 대해 알아보고자 하였다. 고무스프링의 동적 압축실험을 수행하기 위하여, L80-D55, L90-D58, L100-D60의 고무스프링의 형상계수를 구하여 총 9개의 고무스프링을 주문 제작 하여 실험에 사용하였다. 실험은 고무스프링의 길이에 따라 기압축을 제어하여 수행하였으며, 기압축은 변형률의 5%, 10%, 15%, 20%, 25% 순서로 증가시켰다. 실험결과를 통해 힘-변형률 곡선을 얻을 수 있었고, 변형률의 증가함에 따라 강도감소 현상과 강도증가 현상이 발생함을 확인하였다. 또한 고무스프링의 크기와 지름에 따라 강성저하 및 강성증가 현상이 확연하게 나타남을 확인하였고, 힘-변형률 곡선에서 할선기울기를 이용하여 유효 압축강성도를 추정하였다. 유효압축강성도를 이용하여 실제 설계에 사용할 수 있는 설계값을 제시하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.941-946
• /
• 2001

The objectives of this study are to investigate effective stiffness of Rectangular reinforced concrete bridge columns. It is reasonable to use yielding effective stiffness of columns in seismic bridge design, especially in case that plastic hinges form at the bridge columns. In this study, the material nonlinear analysis was conducted for 3, 240 column sections of which variables were the concrete compressive stress, the steel yielding stress, the longitudinal steel location parameter, the longitudinal steel ratio, the axial load level, and the diameter of section. Based on the analytical results, an effective stiffness including two variables(longitudinal steel ratio and axial load ratio) was proposed by regression analyses, and it is compared with test results and the proposed equation for yielding effective stiffness of circular bridge columns.

• 한국강구조학회 논문집
• /
• 제9권2호통권31호
• /
• pp.171-179
• /
• 1997

고장력 볼트 이음부에서의 힘의 전달은 부재간의 압축력 및 볼트축력에 의하여 외력과 균형을 이룸으로서 형성되어지며, 부재간의 압축력, 도입된 축력의 변화 및 미끄러짐하중 등은 볼트 체결부 및 볼트의 유효강성에 지배된다. 이때 유효강성은 일반적으로 접합부의 유효단면적과 탄성계수의 곱으로 나타내어지지만 접합부재의 유효단면적이 어느 정도가 되는지는 판단하기가 쉽지가 않다. 이를 위해서 종래에는 이음부의 탄성변형에 관계하는 유효단면적을 등가중공원통형으로 가정하여 이에 대한 여러 가지 검토가 이루어졌다. 그러나 이러한 제안식들은 설계상의 목적과 복잡한 계산을 피하기 위하여 매우 단순화시킨 것으로 어느 식이 타당한 지는 단정하기가 어려우며 이에 대한 상세한 해석적인 검토 및 실험적인 검증이 요구된다. 따라서, 본 연구에서는 볼트 축력에 의한 접합부재의 유효단면적 산정과 이에 대한 검증을 위하여 고장력 볼트 이음 시험편에 대해 피로시험을 실시하고 반복하중 재하 후의 마찰면의 형상을 관찰하여 유효마찰 영역을 측정하였으며, 유한 요소법에 의해 수치 해석을 실시하여 내부 압축응력의 분포형상을 밝히고 접촉면상에 발생하는 응력 분포영역을 근사화하므로서 마찰면의 형상과 내부 압축응력의 분포영역과의 관계 그리고 유효단면적의 산정 방법을 고찰하였다.

• Structural Engineering and Mechanics
• /
• 제70권4호
• /
• pp.499-511
• /
• 2019

In this study, the axial compressive behavior of novel quadruple C-channel built-up cold-formed steel columns with different slenderness ratio was investigated, using the experimental and numerical analysis. The axial compressive capacity and failure modes of the columns were obtained and analyzed. The finite element models considering the geometry, material and contact nonlinearity were developed to simulate and analyze the structural behavior of the columns further. There was a great correlation between the numerical analyses and test results, which indicated that the finite element model was reasonable and accurate. Then influence of, slenderness ratio, flange width-to-thickness ratio and screw spacing on the mechanical behavior of the columns were studied, respectively. The tests and numerical results show that due to small slenderness ratio, the failure modes of the specimens are generally local buckling and distortional buckling. The axial compressive strength and stiffness of the quadruple C-channel built-up cold-formed steel columns decrease with the increase of maximum slenderness ratio. When the screw spacing is ranging from 150mm to 450mm, the axial compressive strength and stiffness of the quadruple C-channel built-up cold-formed steel columns change little. The axial compressive capacity of quadruple C-channel built-up cold-formed steel columns increases with the decrease of flange width-thickness ratio. A modified effective length factor is proposed to quantify the axial compressive capacity of the quadruple C-channel built-up cold-formed steel columns with U-shaped track in the ends.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 가을 학술발표회 논문집
• /
• pp.278-283
• /
• 1993

Though stiffnesses of joints in precast concrete (P.C) large structures are known to be generally less than those in monolithic reinforced concrete wall structures, designers have very little information on the quantitative values with regards to these stiffnesses. The aim of this paper is to provide this quantitative information, in particular, on the compressive stiffness of horizontal joints, based on the analytical results derived from several experiments. Also, it is shown that the approach from the contact problem to determine this stiffness gives a value very similar to those obtained above.

• Earthquakes and Structures
• /
• 제9권3호
• /
• pp.481-501
• /
• 2015

Current design codes and technical recommendations often provide rough indications on how to assess effective stiffness of Reinforced Concrete (R/C) frames subjected to seismic loads, which is a key factor when a linear analysis is performed. The Italian design code (NTC-2008), Eurocode 8 and ACI 318 do not take into account all the structural parameters affecting the effective stiffness and this may not be on the safe side when second-order $P-{\Delta}$ effects may occur. This paper presents a study on the factors influencing the effective stiffness of R/C beams, columns and walls under seismic forces. Five different approaches are adopted and analyzed in order to evaluate the effective stiffness of R/C members, in accordance with the scientific literature and the international design codes. Furthermore, the paper discusses the outcomes of a parametric analysis performed on an actual R/C building and analyses the main variables, namely reinforcement ratio, axial load ratio, concrete compressive strength, and type of shallow beams. The second-order effects are investigated and the resulting displacements related to the Damage Limit State (DLS) under seismic loads are discussed. Although the effective stiffness increases with steel ratio, the analytical results show that the limit of 50% of the initial stiffness turns out to be the upper bound for small values of axial-load ratio, rather than a lower bound as indicated by both Italian NTC-2008 and EC8. As a result, in some cases the current Italian and European provisions tend to underestimate second-order $P-{\Delta}$ effects, when the DLS is investigated under seismic loading.

• 한국융합학회논문지
• /
• 제7권4호
• /
• pp.181-190
• /
• 2016

The objective of this study is to find the effective stiffness and compressive strengths of a unit-cell pinwheel truss and double pinwheel truss model designed following a double helical geometry similar to that of the DNA (deoxyribonucleic acid) structure in biology. The ideal solution for their derived relative density is correlated with a ratio of the truss thickness and length. To validate the relative stiffness or relative strength, ABAQUS software is used for the computational model analysis on five models having a different size of truss diameter from 1mm to 5mm. Applied material properties are stainless steel type 304. The boundary conditions applied were fixed bottom and 5 mm downward displacement. It was assumed that the width, length, and height are all equal. Consequently, it is found that the truss model has a lower effective stiffness and a lower effective yielding strength.

• Structural Engineering and Mechanics
• /
• 제38권4호
• /
• pp.459-477
• /
• 2011

Due to the low elastic modulus of FRP, concrete members reinforced with FRP rebars show greater deflections than members reinforced with steel rebars. Deflection is one of the important factors to consider the serviceability of horizontal members. In this study flexural test of AFRP reinforced concrete beams was performed considering reinforcement ratio and compressive strength as parameters. The test results indicated that flexural capacity and stiffness increase in proportion to the reinforcement ratio. The test results were compared with existing proposed equations for the effective moment of inertia including ACI 440. The most of the proposed equations were found to over-estimate the effective moment of inertia while the equation proposed by Bischoff and Scanlon (2007) most accurately predicted the values obtained through actual testing.

• 콘크리트학회지
• /
• 제6권3호
• /
• pp.142-151
• /
• 1994

프리캐스트 콘크리트 대형판 구조물에 있어서 접합부의 강성은 일반적으로 일체식 철근 콘클리트 벽식구조물에 비하여 떨어지는 것으로 알려져있으나 이들 강성에 대한 정량적인 값에 대한 정보가 매우 부족한 실정이다. 이 논문은 몇가지 실험으로부터 도출된 해석적 결과에 근거하여 특히 수평접합부의 압축강도에 관한 정량적 정보를 제공하는 것을 목적으로 한다. 또한 접촉문제로부터의 접근에 의해 구해진 수평접합부의 압축강성값이 위에서 얻은 값들과 매우 유사함을 보여주고 있다.