• Journal of The Korean Society of Agricultural Engineers
• /
• v.63 no.6
• /
• pp.17-26
• /
• 2021

Greenhouses have been damaged due to the uplift pressure from strong wind, for which rebar piles are often installed near the greenhouse to resist the pressure. For the effective design of rebar piles, it is necessary to access the shear strength of soil on which the greenhouse is constructed. This study experimentally evaluates the shear strength of the soil beneath the greenhouse. Four soil samples were collected from four agricultural sites, and prepared for testing with 75, 80, 85, and 90% compaction rates. One-dimensional unconfined compression test (UC), consolidated-undrained triaxial test (CU), and resonant column test (RC) were performed for the evaluation of shear strength and shear modulus. Generally, the higher shear strength and modulus were observed with the higher compaction rates. In particular, the UC shear strength increases with the increase of #200 sieve passing rate. Resulting from the CU test, the sample with the most of coarse soil had the highest friction angle, but the variation is small among samples. Resulting from the CU and RC tests, the ratio of maximum shear modulus with the major principle stress at failure was the higher at the finer soil. The ratio was two to three times greater than the ratio from the standard sand. This indicates that the shear strength is lower for the fine soil than the coarse soil at the same shear modulus. The results of this study will be a useful resource for the estimation of the pull-out strength of the rebar pile against the uplift pressure.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.1
• /
• pp.26-33
• /
• 2007

The intake swirl motion, as one of dominant effects for an engine combustion. is very effective for turbulence enhancement during the compression process in the cylinder of 2-valve engine. Because the combustion flame speed is determined by the turbulence that is mainly generated from the mean flow of the charge air motion in intake port system. This paper describes the experimental results of swirl flow and combustion characteristics by using the oil spot method and back-scattering Laser Doppler velocimeter (LDV) in 2-valve single cylinder transparent LPG engine using the liquid phase LPG injection. For this. various intake port configurations were developed by using the flow box system and swirl ratios for different intake port configurations were determined by impulse swirl meter in a steady flow rig test. And the effects of intake swirl ratio on combustion characteristics in an LPG engine were analyzed with some analysis parameters that is swirl ratio. mean flow coefficient, swirl mean velocity fuel conversion efficiency. combustion duration and cyclic variations of indicated mean effective pressure(IMEP). As these research results, we found that the intake port configuration with swirl ratio of 2.0 that has a reasonable lean combustion stability is very suitable to an $11{\ell}$ heavy-duty LPG engine with liquid phase fuel injection system. It also has a better mean flow coefficient of 0.34 to develope a stable flame kernel and to produce high performance. This research expects to clarify major factor that effects on the design of intake port efficiently with the optimized swirl ratio for the heavy duty LPG engine.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.4B
• /
• pp.715-724
• /
• 2000

This Paper presents 3-D subband filter banks which are effective for progressive and lossless compression of volumetric images. For such a purpose, ORT(Overlapping Rounding Transform), applied so far to 1-D losslesssubband filter banks, is now used to implement two types of 3-D lossless subband filter banks: separable andnon-separable types. Separable fiter banks are implemented form applying 1-D lossless filter banks consecutively.Non-separable later banks are developed by expanding the 1-D ORT into 3-D one. In particular, the proposed ORT based 3-D non-separable filter banks generalizes the 3-D HINT(Hierarchical INTerpolation) algorithm.Through the experiment comparisons on various volumetric medical images, we prove that the proposedseparablefnon-separable filter banks perform better, in terms of compression ratio (first order entropy), than theother lossless compression techniques such as block based transform and conventional 3-D HINT.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.8
• /
• pp.5-9
• /
• 2013

In this study, it was examined a strength characteristic of organic acid material that is eco-friendly and low energy as a soil improving material. The object of this study is to analysis of strength changes with observing the clay mixed organic acid material through the unconfined compression strength test and triaxial compression test during 28 days. As a result of the tests, the strength of clay mixed organic acid material is increased when the more ages are prolonged, the more organic acid material mixture ratio growed. Therefore, in grasping the strength improvement effects of clay by organic acid material mixing, it confirmed that organic acid material as soil improving material is effective through unconfined compression strength test and triaxial compression test. Through this test, the definite strength increase is confirmed according to the mixture of the organic acid material and the possibility of soil improvement is also confirmed based on this result. From now on, detailed examination and field test will help closely to definite strength characteristics.

• Journal of Korean Neurosurgical Society
• /
• v.45 no.6
• /
• pp.369-374
• /
• 2009

Objective : Percutaneous vertebroplasty (VP) can provide immediate stabilization in pathologic fractures of spinal tumors. However, long term follow-up data in cases of pathologic fractures are lacking. The authors report follow-up results of VP in 185 pathologic fractures of 102 spinal tumor patients. Methods : Percutaneous VP was performed at 185 vertebral bodies of 102 patients from 2001 to 2007. Retrospective analysis was done with medical records and radiological data. The change of visual analogue score (VAS), vertebral body (VB) height and kyphotic angle were measured preoperatively and on postoperative one day and at 3, 6, and 12 months. Results : The patients were composed of metastatic spine tumors (81%) and multiple myeloma (19%). Involved spinal segments were between T6 and L5. Mean follow-up period was 12.2 months. VAS for back pain was 8.24 preoperatively, 3.59 (postoperative one day), 4.08 (three months) and 5.22 (one year). VB compression ratio changed from 21.33% preoperatively to 13.82% (postoperative one day), 14.36% (three month), and 16.04% (one year). Kyphotic angle changed from $15.35^{\circ}$ preoperatively to $12.03^{\circ}$ (postoperative one day), $13.64^{\circ}$ (three month), and $15.61^{\circ}$ (one year). Conclusion : Immediate pain relief was definite after VP in pathologic compression fracture of osteolytic spinal disease. Although VAS was slightly increased on one year follow-up, VP effect was maintained without significant change. These results indicate that VP could be a safe and effective procedure as a palliative treatment of the spinal tumor patients.

• Journal of Advanced Navigation Technology
• /
• v.14 no.1
• /
• pp.93-101
• /
• 2010

In this study, the performance characteristics of turbocharged engine is analyzed. The methods of engine performance improvements are suggested not only for full load characteristics of the engine but also for partial load characteristics of the engine, which is more frequently used in actual driving conditions. The compression ratio of the compressor is increased rapidly in a straight line pattern until 1260 engine rpm, and after that it is increased slowly to 2.5 ratio. Also the brake mean effective pressure increased until 1260 engine rpm and decreased rapidly after 1600 engine rpm. The higher the pressure ratio, the better the fuel consumption, air excess ratio and brake mean effective pressure. But those are higher in the rated revolution range than in the mid-low revolution range. The turbocharger is operated in a stable condition from 1260 rpm and its efficiency is low in the low speed range for the reason of its characteristics. The results of this study can be applied in the fundamental control methods of turbocharged engine for stable load and speed.

• Steel and Composite Structures
• /
• v.37 no.4
• /
• pp.481-492
• /
• 2020

Twenty-two corrosion-damaged columns were simulated through accelerated steel corrosion tests. Eight specimens were directly tested to failure under axial load, and the remaining specimens were tested after concrete-filled steel tube (CFST) strengthening. This study aimed to investigate the damage of RC columns after corrosion and their restoration and enhancement after strengthening. The research parameters included different corrosion degrees of RC columns, diameter-to-thickness ratio of steel tube and the strengthening concrete strength. Experimental results showed that CFST strengthening method could change the failure mode of corrosion-damaged RC columns from brittleness to ductility. In addition to the bearing capacity provided by the strengthening materials, it can also provide an extra 26.7% amplification because of the effective confinement provided by steel tubes. The influence of corrosion on reinforcement and concrete was quantitatively analysed and considered in the design formula. The proposed formula accurately predicted the bearing capacity of the strengthened columns with a maximum error of only 7.68%.

• Journal of the Korea Concrete Institute
• /
• v.16 no.4 s.82
• /
• pp.565-572
• /
• 2004

The mechanical behavior of concrete-filled glass fiber reinforced polymer columns is affected by various factors including concrete strength, stiffness of tube, end confinement effect, and slenderness ratio of members. In this research the behavior of slender columns was examined both experimentally and analytically. Experimental works include 1) compression test with 30cm long glass fiber composite columns under different end confinement conditions, 2) uni-axial compression test for 7 slender columns, which have various slenderness ratios. Short-length stocky columns gave high strength and ductility revealing high confinement action of FRP tubes. The strength increment and strain change were examined under different end confinement conditions. With slender columns, failure strengths, confinement effects, and stress-strains relations were examined. Through analytical work, effective length was computed and it was compared with the amount of reduction in column strength, which is required to predict design strength with slender specimens. This study shows the feasibility of slender concrete-filled glass fiber reinforced polymer composite columns.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.20 no.7
• /
• pp.2375-2385
• /
• 1996

As a compression wave is emitted from a duct, an impulsive wave generates and causes an impulsive noise that is at present a serious environmental noise pollution. In order to clarify the acoustic characteristics of the noise and to reduce their pressure levels, a series of model experiments were conducted on the impulsive waves emitted from an open end of a shock tube. The impulsive waves with various intensities were obtained by controlling the operation pressure ratio of the shock tube. Various kinds of silencers such as the exit boxes with baffle plates, were applied to the duct exit to reduce the impulsive noises. The effects of geometry of silencers and shock Mach number on the noise reduction were clarified. From the measurements of sound pressure level, it was found that installing the baffle plate into the exit box is effective in lowering the noise level at far fields, and that the recommendable geometries of silencer are L/D=1, H/D=1 and H/D=0.75.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.44 no.1
• /
• pp.78-85
• /
• 1999

To investigate kernel hardness, a compression test which is widely used to measure the hardness of individual kernels as a physical testing method was made simultaneously with the measurement of friabilin (15KDa) which is strongly associated with kernel hardness and was recently developed as a biochemical marker for evaluating kernel hardness in 79 Korean wheat varieties and experimental lines. With the scattered diagram based on the principal component analysis from the parameters of the compression test, 79 Korean wheat varieties were classified into three groups based on the principal component analysis. Since conventional methods required large amount of flour samples for analysis of friabilin due to the relatively small amount of friabilin in wheat kernels, those methods had limitations for quality prediction in wheat breeding programs. An extraction of friabilin from the starch of a single kernel through cesium chloride gradient centrifugation was successful in this experiment. Among 79 Korean wheat varieties and experimental lines 50 lines (63.3%) exhibited a friabilin band and 29 lines (36.7%) did not show a friabilin band. In this study, lines that contained high maximum force and the lower ratio of minimum force to maximum force showed the absence of the friabilin band. Identification of friabilin, which is the product of a major gene, could be applied in the screening procedures of kernel hardness. The single kernel analysis system for friabilin was found to be an easy, simple and effective screening method for early generation materials in a wheat breeding program for quality improvement.