• The Journal of Advanced Prosthodontics
• /
• 제4권2호
• /
• pp.93-96
• /
• 2012

PURPOSE. The objective of this study was to compare the light transmittance of zirconia in different thicknesses using various light curing units. MATERIALS AND METHODS. A total of 21 disc-shaped zirconia specimens (5 mm in diameter) in different thicknesses (0.3, 0.5 and 0.8 mm) were prepared. The light transmittance of the specimens under three different light-curing units (quartz tungsten halogen, light-emitting diodes and plasma arc) was compared by using a hand-held radiometer. Statistical significance was determined using two-way ANOVA (${\alpha}$=.05). RESULTS. ANOVA revealed that thickness of zirconia and light curing unit had significant effects on light transmittance ($P$ <.001). CONCLUSION. Greater thickness of zirconia results in lower light transmittance. Light-emitting diodes light-curing units might be considered as effective as Plasma arc light-curing units or more effective than Quartz-tungsten-halogen light-curing units for polymerization of the resin-based materials.

• KIEAE Journal
• /
• 제12권2호
• /
• pp.53-58
• /
• 2012

Daylight is one of the most critical factors that can be utilized for architectural spaces; compared to artificial light, it is a sustainable energy source without the cost of electric energy and offers a more natural feeling to the visitors in the building. To make the space quality better, many architects have tried to predict daylight performance during the design process. The aim of this study is to evaluate the daylight transmittance efficacies of the five shapes - Flat, Pyramid, Dome, Barrel Vault. Ridge - of skylights. The results of this study indicated that the differences of transmittance efficiency among various skylights were less than 4.6% except the flat shaped skylight. Therefore, this study shows that there were no big differences of the daylight transmittance efficacies among the shapes of skylights.

• KIEAE Journal
• /
• 제16권1호
• /
• pp.5-10
• /
• 2016

Purpose: The energy consumption in buildings has continuously increased in some countries and it reaches almost 25% of the total energy use in korea. Therefore there are various efforts to minimize energy consumption in buildings, and the regulations on building envelope insulation have been tightened up gradually. To satisfy the building regulation, the use of vacuum insulation panels(VIPs) is increasing. VIP is a high performance insulation materials, so that it can be thinner than conventional insulation material. When VIP is applied in a building, it may cause thermal bridge, which occurs due to very low thermal conductivity compared to other building materials and the envelope of VIPs. Method: This study designed the capsulized VIPs using conventional insulation for reduction of the thermal bridge. Then designed VIPs were applied to a wall. The linear thermal transmittance and the effective thermal conductivity were analyzed by HEAT2 simulation program for two dimensional steady-state heat transfer. The result compared with a wall with non-capsulized VIPs. Result: It analyzed that the wall with capsulized VIPs had lower linear thermal transmittance and reduced the difference of the effective thermal transmittance with one dimensional thermal transmittance compared to that of the wall with non-capsulized VIPs.

• Current Photovoltaic Research
• /
• 제3권3호
• /
• pp.91-96
• /
• 2015

Optical modeling and characterization of transparent dye-sensitized solar cells (DSC) are presented to design and estimate DSC devices numerically. In order to model the inhomogeneous active layer of DSC, the porous structure of titanium oxide ($TiO_2$) and dye mixture, we prepared films consisting of layer by layer of the DSC's basic materials sequentially, and characterized the optical parameters of the films with the effective refractive index, which was extracted from the transmittance and reflectance measurements in ultra violet to near infra-red range. By using the effective refractive index, we made the optical model for DSC, and demonstrated that the optical model based on effective refractive index can be used to design and evaluate the performance of transparent-type DSC modules.

• 한국세라믹학회지
• /
• 제42권6호
• /
• pp.399-404
• /
• 2005

Anti-reflection film was coated by using spherical silica nano colloidal particles and fumed silica particles. Silica colloid sol was reserved between two inclined slide glasses by capillary force, and particles were stacked to form a film onto the substrate as the upper glass was sliding. The deposition processes were studied to enhance the wavelength dependency of the light transmittance and to control the effective refractive index of the film. Both of the spherical and fumed silica particles showed an enhancement of $4.0-4.4\%$ in light transmittance by one step coating. The dependence of the transmittance on wavelength was largely improved at the longer wavelength by partial coating of fumed particles on the film of spherical particles. The effective refractive index of the film was controlled by removing latex particles that were co-deposited with silica particles. Using this process the light reflectance from one side of the glass substrate could be reduced from $4.2\%$ to $0.6\%$ although zero reflectance was not achieved due to the agglomeration of the latex particles.

• 한국재료학회지
• /
• 제15권5호
• /
• pp.285-292
• /
• 2005

Anti-reflection film was coated by using spherical silica nano colloids. Silica colloid sol was reserved between two inclined slide glasses by capillary force, and particles were convectively stacked to form a film onto the substrate as the water evaporates. As the sliding speed increased, the thickness of the film decreased and the wavelength at the maximum transmittance decreased. The microstructure observed by SEM showed that silica particles were nearly close packed, which enabled the calculation of the effective refractive index of the film. The film thickness was measured by proffer and calculated from the wavelength of maximum transmittance and the effective refractive index. The effective refractive index of the film could be controlled by a subtle controlling of the coating speed and by mixing two different sized silica particles. When the 100 nm and 50 m particles were mixed at 4:1-5:1 volume ratio, the maximum transmittance of $95.2\%$ for one-sided coating was obtained. This is the one that has increased by $3.8\%$ compared to bare glass substrate, and shows that $99.0\%$ of transmittance or $1.0\%$ of reflectance can be achieved by the simple process if both sides of the substrate are coated.

• 펄프종이기술
• /
• 제38권1호통권113호
• /
• pp.9-15
• /
• 2006

To develop an efficient and cost effective on-line method to determine the stock consistency a study on the relationship between the turbidity and transmittance of stocks and their consistency was carried out using a system consisted of a dynamic drainage jar, pump and turbidometer. Results shooed that the wavelength of 525 nm was most effective for measuring turbidity. As the consistency increases the turbidity increases, and their relationship can be depicted in the second order equations. On the other hand the relationship between consistency and transmittance can be described in exponential equations. From these equations the consistencies of stock samples can be determined using the measured values of turbidity or transmittance.

• 한국세라믹학회지
• /
• 제41권10호
• /
• pp.766-770
• /
• 2004

구형 실리카 나노 콜로이드 입자를 이용하여 반사방지막을 제조하였다. 실리카 콜로이드 현탁액을 모세관 힘을 이용하여 기울어진 두 장의 유리판 사이에 저장한 후 위의 유리를 이동시켜 반사 방지막을 코팅하였다. 상판 유리의 이동속도가 빨라질수록 막의 두께는 감소하였고, 막의 두께 변화에 따라 광 투과율이 변하였다. SEM으로 관찰된 실리카 나노 입자는 최밀충진에 가깝게 유리 기판에 부착되어 있었으며, 이로부터 고체 입자와 기공을 포함하는 막의 유효 굴절율을 구하였다. 최대의 광투과율을 나타내는 파장과 유효 굴절율로 부터 계산한 막의 두께는 SEM 사진 및 profiler로 구한 값과 잘 일치하였다. $94.7\%$의 최대 광투과율을 얻었으며, 양면으로 코팅한다면 $97.4\%$의 투과율 즉 $1.3\%$의 반사율을 얻을 수 있는 것으로 나타났다.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2007년도 7th International Meeting on Information Display 제7권1호
• /
• pp.549-552
• /
• 2007

Patterned vertical alignment (PVA) mode requires multi-domain to exhibit wide viewing angle whereas the transmittance is sacrificed. To overcome the demerit, a fine pattern was formed at folded region in PVA Z-shape electrode structure. In the present work fine patterns were formed near domain boundary regions where the unwanted field direction which causes the LC to tilt down in unwanted direction exists. Thereby transmittance is improved near those fine patterns. This method is very simple and more cost-effective process than the other methods. In this article, we show the method of fine pattern formation and its influence on LC molecule in PVA mode with Z-shape electrode structure.

• 한국의류학회지
• /
• 제43권4호
• /
• pp.592-604
• /
• 2019

This study examines the stealth function of sputtered fabric with an infrared thermal imaging camera in terms of the thermal and infrared (IR) transmittance characteristics. Various base fabrics were selected, infrared imaging was performed, and infrared transmittance was measured. By infrared camera experiment it was found that the sample was concealed because it had a similar color to the surroundings when the aluminum layer was directed toward the outside. In addition, a comparison of the infrared thermographic image of the untreated sample and the sputtered sample in the laboratory showed that the difference in ${\Delta}E$ value ranged from 31 to 90.4 and demonstrated effective concealment. However, concealment was not observed in the case of the 3-layer (Nylon-Al-Nylon) model when a sputtered aluminum layer existed between two nylon layers. The direction of the sputtering layer did not affect the infrared transmittance in the infrared transmittance experiment. Therefore, it seems better to interpret the concealing effect in the infrared thermographic images by using thermal transfer theory rather than infrared transmittance theory. We believe that the results of this study will be applicable to developing high performance smart clothing and military uniforms.