• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1390-1392
• /
• 2001

ZnO-based SAW(surface acoustic wave) filters are fabricated with the configuration of IDT/ZnO/$SiO_2$/Si(100) using various IDT materials such as Al, Cu/Ti, and Cu/Al. Their frequency response characteristics are measured and compared. The thickness of Al IDT is varied to examine the mass loading effect. In addition, effects of thermal treatment and electrical stress on the frequency responses of the fabricated SAW filters are investigated.

• KSBB Journal
• /
• v.8 no.5
• /
• pp.424-430
• /
• 1993

The anti-stress effect by the treatment of vitamin C was investigated in this study. The treatment of ascorbic acid in the presence of $Cu^{2+}$ion induced strong time- and dose-dependent degradation of hitamine, and also the addition of histamine accelerated time-dependent decomposition of ascorbic acid in vitro. The treatment of ascorbic acid in $ODS^{od}/_{od}$rats, which cannot synthesize ascorbic acid, significantly decreased the urinary histamine. The protreatment of ascorbic acid, dexamethasone and promethazine inhibited the lethal effect induced by immobilization stress, but that of dimethylsulfoxide did not. The addition of ascorbic and to a culture of spleen cells of $ODS^{od}/_{od}$rats significantly increased the Con A-dependent T lymphocyte proliferation.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1996.04a
• /
• pp.99-107
• /
• 1996

Examined in this paper is the effect of B$_{4}$C addition on the frictional characteristics of Cu-Sn based sintered friction material. For the specimens 1%, 2% and 4% of B$_{4}$C were added into the reference material. A pin-on-disk type friction tester was used to measure the friction and wear with respect to the surface temperature and sliding distance. Wear mechanism of each specimen is analyzed in the view point of the oxide film formation. The specimen containing 4% of B$_{4}$C showed stable friction and low wear since the oxide film was sustained up to higher surface temperature ranges.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.253-254
• /
• 2006

We have manufactured CdS and Cd(Cu)S thin films by chemical bath deposition(CBD) process, and examined the effects of $NH_4Cl$ and TEA. The addition of $NH_4Cl$ remarkably enhanced the film thickness of CdS, however, TEA slightly decreased the film thickness. The thickness of CdS film prepared from the aqueous solution of 0.003 M $CdSO_4$ 0.00008 M $CuSO_4$, 1.3M NH3, 0.03 M $SC(NH_2)_2$ and 0.0009 M $NH_4Cl$ was 210 nm and resistivity of that was $1.2{\times}10^3{\Omega}cm$.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.48-54
• /
• 1996

Examined in this paper, is the effect of B$_{4}$C addition on the frictional characteristics of Cu-Sn based sintered friction materials. For the specimens 1wt%, 2wt% and 4wt% of B$_{4}$C were added into the reference material. A pin-on-disk type friction tester was used to,measure the friction torque with respect to the surface temperature and sliding distance. Wear mechanism of each specimen is analyzed in the view point of the oxide film formation. The specimen containing 4wt% of B$_{4}$C showed stable friction and low wear since the oxide film was sustained up to higher surface temperature ranges.

• Journal of the Korean Ceramic Society
• /
• v.29 no.2
• /
• pp.95-100
• /
• 1992

A high-Tc superconducting phase was obtained using long sintering time of 210 hours. From XRD and SEM analyses, it could be confirmed that the particles were plate phase, of which the structure is tetragonal system with lattice parameter a=b=5.44${\AA}$, C=37.18${\AA}$. Resistance and current density measurements were carried out using 4 probe method. The experimental data revealed that the stable high-Tc superconducting phase was easily formed by addition of Pb to Bi-system. Therefore, we could find the sintering condition to synthesis the system having the largest fraction of high Tc phase.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.2
• /
• pp.639-644
• /
• 2011

A simple and highly sensitive chemiluminescence method to determine norfloxacin (NFLX) has been proposed by measuring the chemiluminescence (CL) intensities using a flow injection (FI) system. The CL intensity of the luminol-$H_2O_2$ system is strongly enhanced by the addition of Cu (II) in alkaline condition. The CL intensity is substantially increased after the injection of NFLX into the luminol-$H_2O_2$-Cu (II) system. The enhancement effect is attributed to a catalytic effect of Cu (II) due to the interaction with NFLX which forms a complex with the catalyst. Under the optimal conditions, the sensitizing effect of the CL intensity is proportional to the concentration of NFLX in the range of $1.5{\times}10^{-9}-5.9{\times}10^{-7}molL^{-1}$ (r = 0.9994) with a detection limit ($3{\sigma}$) of $2.98{\times}10^{-10}molL^{-1}$. The proposed method had good reproducibility with the relative standard deviation (RSD, n = 5) of 1.6% for $1{\times}10^{-7}molL^{-1}$ of NFLX. The possible reaction mechanism of the CL reaction is also discussed. This method has been successfully applied for the determination of trace amount of NFLX in pharmaceutical preparations and serum samples.

• Journal of Korean Society of Water and Wastewater
• /
• v.35 no.4
• /
• pp.301-309
• /
• 2021

Chitosan, natural organic polymer, has been applied in water treatment as adsorbent due to non-toxic for human being. The amino group as functional group, can interacts with cation and anion at the same time. The prepared chitosan bead (HCB) was crosslinked to increase chemical stability (HCB-G) and both HCB and HCB-G were prepared to increase physical strength by drying referred to DCB and DCB-G, respectively. The adsorption effect for crosslinking and drying for four types of chitosan bead was tested using pseudo fist order (PFO), pseudo second order (PSO), and intraparticle diffusion model (ID). Regardless of PFO and PSO, the order of K, rate constant, is as followed: HCB > HCB-G > DCB > DCB-G for Cu(II) and phosphate. Drying leading to contraction of bead significantly reduced adsorption rate due to reduce the porosity of chitosan. In addition, crosslingking also negatively effect on adsorption rate. When compared with Cu(II) using hydrogel bead, phosphate showed higher value than Cu(II) for PFO and PSO. The application of ID showed that both hydrogel beads (HCB and HCB-G) obtained a very low R² ranging to 0.37 to 0.81, while R² can be obtained to over 0.9 for DCB and DCB-G, indicting ID is appropriate for low adsorption rate.

• Environmental Engineering Research
• /
• v.18 no.3
• /
• pp.177-189
• /
• 2013

Studies were carried out on the speciation of heavy metals (Zn, Cu, Mn, Fe, Ni, Pb, Cd, and Cr) during rotary drum composting of water hyacinth (Eichhornia crassipes) for a period of 20 days. Five different proportions of cattle manure, water hyacinth and sawdust were prepared for composting. This study concluded that, rotary drum was very efficient for the degradation of organic matter as well as for the reduction of mobility and bioavailability of heavy metals during water hyacinth composting. The results from the sequential extraction procedure of heavy metals shows that rotary drum composting changed the distribution of five fractions of Zn, Cu, Mn, Fe, Ni, Pb, Cd, and Cr. The highest reduction in the bioavailability factors of Pb and Cd was observed during the process. The total concentration of Cu, Cr, and Cd was very low compared to the other metals (Zn, Mn, Fe, Ni, and Pb); however, the percentage of exchangeable and carbonate fractions of these metals was similar to other metals. These results confirmed that the bioavailability of metals does not depend on the total concentration of metals. From this study, it can be concluded that the addition of an appropriate proportion of cattle manure significantly reduced the mobile and easily available fractions (exchangeable and carbonate fractions) during water hyacinth composting in rotary drum.

• Environmental Engineering Research
• /
• v.24 no.2
• /
• pp.339-346
• /
• 2019

In this research, applicability of electrochemical technology in removing nitrogenous compounds from solid waste landfill leachate was examined. Novel cathode material was developed at laboratory by introducing a Cu layer on Al substrate (Cu/Al). Al and mild steel (MS) anodes were investigated for the efficiency in removing nitrogenous compounds from actual leachate samples collected from two open dump sites. Al anode showed better performances due to the effect of better electrocoagulation at Al surface compared to that at MS anode surface. Efficiency studies were carried out at a current density of $20mA/cm^2$ and at reaction duration of 6 h. Efficiency of removing nitrate-N using Al anode and developed Cu/Al cathode was around 90%. However, for raw leachate, total nitrogen (TN) removal efficiency was only around 30%. This is due to low ammonium-N removal as a result of low oxidation ability of Al. In addition to the removal of nitrogenous compounds, reactor showed about 30% removal of total organic carbon. Subsequently, raw leachate was diluted four times, to simulate pre-treated leachate. The diluted leachate was treated and around 88% removal of TN was achieved. Therefore, it can be said that the reactor would be good as a secondary or tertiary treatment step in a leachate treatment plant.