• Journal of Biomedical Engineering Research
• /
• v.20 no.1
• /
• pp.53-58
• /
• 1999

Eddy current in MRI systems degrades gradient field linearity and distorts gradient waveform. When the waveform distortion is spatially variant, it is very difficult to perform special imaging techniques such as the echo planar imaging technique or the fast spin echo imaging technique. In this study, we have developed a new technique to estimate the distorted gradient waveforms at any points inside the imaging region using the finite element method. After obtaining the eddy-current-effect transfer function, which represents magnitude and phase characteristics of the gradient field at a particular point, we have used the transfer function to estimate the actual gradient waveforms at the point. To verify the proposed technique, we have compared the estimated gradient waveforms with the measured ones.

• Journal of Electrical Engineering and Technology
• /
• v.12 no.1
• /
• pp.256-261
• /
• 2017

This paper deals with the experimental evaluation on power loss of a double-side permanent magnet synchronous motor/generator (DPMSM/G) applied to a flywheel energy storage system (FESS). Power loss is one of the most important problems in the FESS, which supplies the electrical energy from the mechanical rotation energy, because the power loss decreases the efficiency of energy storage and conversion of capability FESS. In this paper, the power losses of coreless DPMSM/G are separated by the mechanical and rotor eddy current losses in each operating mode. Moreover, the rotor eddy current loss is calculated by the 3-D finite element analysis (FEA) method. The analysis result is validated by separating the power loss as electromagnetic loss and mechanical loss by a spin up/down test.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.120-123
• /
• 1999

We designed and constructed a non-destructive evaluation system using an HTS DC SQUID electronic gradiometer. Our DC SQUID electronic gradiometer is composed of two DC SQUID magnetometers. The system included a non-magnetic stainless steel cryostat and a set of coaxial exciting coils, which were used to induce an eddy current in the test material. We also have calculated the eddy current density produced by an exciting coil in any direction of the testing object. We could compute the eddy current density distribution in 3D. The SQUIDs were computer controlled and the output data from the electronic gradiometer was obtained by using a Labview software.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.92-93
• /
• 1998

In this study, we have established the technique to estimate the gradient waveforms distorted by the eddy current in MRI. After obtaining the eddy current effect transfer function using the finite element method, we have used the transfer function to estimate the output gradient waveforms at any points inside the imaging region. We also present experimental results to be compared with estimated ones.

• Progress in Superconductivity
• /
• v.1 no.2
• /
• pp.115-119
• /
• 2000

We designed and constructed a non-destructive evaluation system using an HTS DC SQUID electronic gradiometer. Our DC SQUID electronic gradiometer is composed of two DC SQUID magnetometers. The system included a non-magnetic stainless steel cryostat and a set of coaxial exciting coils, which were used to induce an eddy current in the test piece. We also have calculated the eddy current density produced by an exciting coil in any direction of the testing object. We could compute the eddy current density distribution in 3D. The SQUIDs were computer controlled and the output data from the electronic gradiometer was obtained by using a Labview software.

• Journal of Sensor Science and Technology
• /
• v.7 no.3
• /
• pp.203-210
• /
• 1998

An experimental study of an eddy current nondestructive testing system to measure dimensions of cylindrical metallic rods, such as cross-sectional area or diameter, is presented. Impedance characteristics of a solenoid sensor, which are generally based on Maxwell's equations in electromagnetic field, are briefly discussed for inspecting geometrical parameters of the coil sensor and testing materials. A measurement system for detecting the diameter of the metallic rod is implemented. This instrument has capabilities for detecting the sensor output signals and estimating demensions of the testing material, continuously. As a result, it was shown that the eddy current sensor with an encircling coil could estimate the diameter of metallic rod. The implemented measurement system gives accurate information for inspecting the dimension of conducting rod with good sensitivity.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.102-104
• /
• 2001

This paper presents a numerical analysis of the eddy current testing for pipe with axi-symmetric defect according to frequency changes using the finite element method(FEM). The defects used in this analysis are inner and outer axi-symmetric type. In order to obtain the behaviors of the signals by changing the frequency, the defects with different depths are modeled and analyzed using FEM. It is important to choose proper frequency because of the effect of skin depth in eddy current testing. This paper describes signal characteristics of each defects as frequency is changed.

• Ocean and Polar Research
• /
• v.23 no.1
• /
• pp.1-10
• /
• 2001

Sea surface temperature derived from infrared images of NOAA satellites showed a warm eddy in the East Korean Bight(EKB) or Donghan Man during the winter 1997${\sim}$2000. To describe the warm eddy in the EKB, hydrographic data collected in 1934 and 1936 were also analyzed. The center of the warm eddy was located at about $39^{\circ}N$ and $129^{\circ}E$. The temperature and salinity of the eddy was about $4.0^{\circ}C$ and 34.0 psu, respectively, at 100m depth. The eddy rotated anticyclonically with a geostrophic current speed of about 20 cm/s. The mean state calculated from the data of 1922${\sim}$1960 showed the existence of a warm eddy over the EKB in winter. The eddy persists until late spring, and disappears from the previous location in summertime, only to be seen again in autumn.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.57 no.3
• /
• pp.214-227
• /
• 2021

The distribution of tidal current and tidal induced residual current, topographical eddies and tidal residual circulation in the waters surrounding the Geumo Island-An Island channel were identified through numerical model experiments and vorticity balance analysis. Tidal current flows southwest at flood and northeast at ebb along the channel. The maximum flow velocity was about 100-150 cm/s in neap and spring tide. During the flood current in the neap tide, clockwise small eddies were formed in the waters west of Sobu Island and southwest of Daebu Island, and a more grown eddy was formed in the southern waters of Geumo Island in the spring tide. A small eddy that existed in the western waters of Chosam Island during the ebb in neap tide appeared to be a more grown topographical eddy in the northeastern waters of Chosam Island in spring tide. Tidal ellipses were generally reciprocating and were almost straight in the channel. These topographical eddies are made of vorticity caused by coastal friction when tidal flow passes through the channel. They gradually grow in size as they are transported and accumulated at the end of the channel. When the current becomes stronger, the topographic eddies move, settle, spread to the outer sea and grow as a counterclockwise or clockwise tidal residual circulation depending on the surrounding terrain. In the waters surrounding the channel, there were counterclockwise small tidal residual circulations in the central part of the channel, clockwise from the northeast end of the channel to northwest inner bay of An Island, and clockwise and counterclockwise between Daebu Island and An Island. The circulation flow rate was up to 20-30 cm/s. In the future, it is necessary to conduct an experimental study to understand the growth process of the tidal residual circulation in more detail due to the convergence and divergence of seawater around the channel.

• Journal of Magnetics
• /
• v.20 no.3
• /
• pp.312-316
• /
• 2015

Unlike conventional Eddy Current Test (ECT), Pulsed Eddy Current (PEC) uses a multiple-frequency current pulse through the excitation coil. In the present study, the detection of subsurface cracks using a specially designed probe that allows the detection of a deeper crack with a relatively small current density has been attempted using the PEC technique. The tested sample is a piece of 304 stainless steel (SS304) with a thickness of 30mm. Small electrical discharge machining (EDM) notches were put in the test sample at different depths from the surface to simulate the subsurface cracks in a pipe. The designed PEC probe consists of an excitation coil and a Hall sensor and can detect a subsurface crack as narrow and shallow as 0.2 mm wide and 2 mm deep. The maximum distance between the probe and the defect is 28 mm. The peak amplitude of the detected pulse is used to evaluate the cracks under the sample surface. In time domain analysis, the greater the crack depth the greater the peak amplitude of the detected pulse. The experimental results indicated that the proposed system has the potential to detect the subsurface cracks in stainless steel plates.