• Korean Chemical Engineering Research
• /
• v.59 no.3
• /
• pp.345-358
• /
• 2021

This study focuses on the development of the liquid air production process that uses LNG (liquefied natural gas) cold energy which usually wasted during the regasification stage. The liquid air can be transported to the LNG exporter, and it can be utilized as the cold source to replace certain amount of refrigerant for the natural gas liquefaction. Therefore, the condition of the liquid air has to satisfy the available pressure of LNG storage tank. To satisfy pressure constraint of the membrane type LNG tank, proposed process is designed to produce liquid air at 1.3bar. In proposed process, the air is precooled by heat exchange with LNG and subcooled by nitrogen refrigeration cycle. When the amount of transported liquid air is as large as the capacity of the LNG carrier, it could be economical in terms of the transportation cost. In addition, larger liquid air can give more cold energy that can be used in natural gas liquefaction plant. To analyze the effect of the liquid air production amount, under the same LNG supply condition, the proposed process is simulated under 3 different air flow rate: 0.50 kg/s, 0.75 kg/s, 1.00 kg/s, correspond to Case1, Case2, and Case3, respectively. Each case was analyzed thermodynamically and economically. It shows a tendency that the more liquid air production, the more energy demanded per same mass of product as Case3 is 0.18kWh higher than Base case. In consequence the production cost per 1 kg liquid air in Case3 was $0.0172 higher. However, as liquid air production increases, the transportation cost per 1 kg liquid air has reduced by $0.0395. In terms of overall cost, Case 3 confirmed that liquid air can be produced and transported with $0.0223 less per kilogram than Base case.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.51 no.6
• /
• pp.1-11
• /
• 2023

By comparing and analyzing the effects of the 2013 Suncheon Bay International Garden Expo and the 2023 Suncheon Bay International Garden Expo, designated as Korea's first national garden, this study aims to present basic data for the future operation direction and sustainability strategy. First, in both fairs, satisfaction throughout the event was high, 4.0 or higher. In particular, the satisfaction level of the 2023 Suncheon Bay International Garden Expo was higher than that of the 2013 Suncheon Bay International Garden Expo. As the longest international event held since the COVID-19 pandemic, it reflected the citizens' demand for healing and recharging in natural spaces. Second, as a result of comparing the types of perceptions that affected satisfaction, it was found that economic, environmental, and ecological types commonly affected satisfaction at the 2013 and 2023 Suncheon Bay International Garden Expo. The 2013 Suncheon Bay International Garden Expo established the brand value as an "ecological city" by creating a garden in the city center along with an ecological resource called Suncheon Bay. In addition, the 2023 Suncheon Bay International Garden Expo expanded the scope of the garden to the entire city center. It also attempted to create a city where humans and nature coexist by realizing values, such as responding to climate change and carbon neutrality. In other words, one of the ways to secure urban competitiveness is to attract corporate investment and tourists and build a differentiated brand in Suncheon by promoting the 2023 fair based on the potential ecological values of the region after the 2013 Suncheon Bay International Garden Expo. Therefore, if the Suncheon Bay International Garden Expo continues to develop environmental and ecological content and programs in line with changes in society and tries to establish itself in citizens' perception through cooperation with local governments and residents, it will be able to establish its identity and brand power.

• Journal of Intelligence and Information Systems
• /
• v.24 no.3
• /
• pp.177-198
• /
• 2018

Recently, as economic property it has become necessary to acquire and utilize the framework for water resource measurement and performance management as the property of water resources changes to hold "public property". To date, the evaluation of water technology has been carried out by feasibility study analysis or technology assessment based on net present value (NPV) or benefit-to-cost (B/C) effect, however it is not yet systemized in terms of valuation models to objectively assess an economic value of technology-based business to receive diffusion and feedback of research outcomes. Therefore, K-water (known as a government-supported public company in Korea) company feels the necessity to establish a technology valuation framework suitable for technical characteristics of water resources fields in charge and verify an exemplified case applied to the technology. The K-water evaluation technology applied to this study, as a public interest goods, can be used as a tool to measure the value and achievement contributed to society and to manage them. Therefore, by calculating the value in which the subject technology contributed to the entire society as a public resource, we make use of it as a basis information for the advertising medium of performance on the influence effect of the benefits or the necessity of cost input, and then secure the legitimacy for large-scale R&D cost input in terms of the characteristics of public technology. Hence, K-water company, one of the public corporation in Korea which deals with public goods of 'water resources', will be able to establish a commercialization strategy for business operation and prepare for a basis for the performance calculation of input R&D cost. In this study, K-water has developed a web-based technology valuation model for public interest type water resources based on the technology evaluation system that is suitable for the characteristics of a technology in water resources fields. In particular, by utilizing the evaluation methodology of the Institute of Advanced Industrial Science and Technology (AIST) in Japan to match the expense items to the expense accounts based on the related benefit items, we proposed the so-called 'K-water's proprietary model' which involves the 'cost-benefit' approach and the FCF (Free Cash Flow), and ultimately led to build a pipeline on the K-water research performance management system and then verify the practical case of a technology related to "desalination". We analyze the embedded design logic and evaluation process of web-based valuation system that reflects characteristics of water resources technology, reference information and database(D/B)-associated logic for each model to calculate public interest-based and profit-based technology values in technology integrated management system. We review the hybrid evaluation module that reflects the quantitative index of the qualitative evaluation indices reflecting the unique characteristics of water resources and the visualized user-interface (UI) of the actual web-based evaluation, which both are appended for calculating the business value based on financial data to the existing web-based technology valuation systems in other fields. K-water's technology valuation model is evaluated by distinguishing between public-interest type and profitable-type water technology. First, evaluation modules in profit-type technology valuation model are designed based on 'profitability of technology'. For example, the technology inventory K-water holds has a number of profit-oriented technologies such as water treatment membranes. On the other hand, the public interest-type technology valuation is designed to evaluate the public-interest oriented technology such as the dam, which reflects the characteristics of public benefits and costs. In order to examine the appropriateness of the cost-benefit based public utility valuation model (i.e. K-water specific technology valuation model) presented in this study, we applied to practical cases from calculation of benefit-to-cost analysis on water resource technology with 20 years of lifetime. In future we will additionally conduct verifying the K-water public utility-based valuation model by each business model which reflects various business environmental characteristics.

• Economic and Environmental Geology
• /
• v.40 no.5
• /
• pp.635-649
• /
• 2007

Geochemical composition, stable isotopes $({\delta}^{18}O,\;{\delta}D,\;{\delta}^{34}S)$ and noble gases(He, Ne and Ar) of nine hot spring water and three groundwater for five hot springs(Jukam, Hwasun, Dokog, Jirisan, Beunsan) from the Honam area were analyzed to investigate the hydrogeochemical characteristics and the hydrogeochemical evolution of the hot spring waters, and to interpret the source of sulfur, helium and argon dissolved in the hot spring waters. The hot spring waters show low water temperature ranging from 23.0 to $30.5^{\circ}C$ and alkaline characteristics of pH 7.67 to 9.98. Electrical conductivity of hot spring waters is $153{\sim}746{\mu}S/cm$. Groundwaters in this area were characterized by the acidic to neutral pH range$(5.85{\sim}7.21)$, the wide electrical conductivity range $(44{\sim}165{\mu}S/cm)$. The geochemical compositions of hot spring and groundwaters can be divided into three water types: (1) $Na-HCO_3$ water type, (2) Na-Cl water type and (3) $Ca-HCO_3$ water type. The hot spring water of $Ca-HCO_3$ water type in early stage have been evolved through $Ca(Na)-HCO_3$ water type into $Na-HCO_3$ type in final stage. In particular, Jurim alkaline(pH 9.98) hot spring water plotted at the end point of $Na-HCO_3$ type in the Piper diagram is likely to arrive into the final stage in geochemical evolution process. Hydrogen and oxygen isotopic data of the hot spring water samples indicate that the hot spring waters originated from the local meteoric water showing latitude and altitude effects. The ${\delta}^{34}S$ value for sulfate of the hot spring waters varies widely from 0.5 to $25.9%o$. The sulfur source of most hot spring waters in this area is igneous origin. However, The ${\delta}^{34}S$ also indicates the sulfur of JR1 hot water is originated from marine sulfur which might be derived ken ancient seawater sulfates. The $^3He/^4He\;and\;^4He/^{20}Ne$ ratios of the hot spring waters range from $0.0143{\times}10^{-6}\;to\;0.407{\times}10^{-6}\;and\;6.49{\sim}584{\times}10^{-6}$, respectively. The hot spring waters are plotted on the mixing line between air and crustal components. It means that the He gas in the hot spring waters was mainly originated from crustal sources. However, the JR1 hot spring water show a little mixing ratio of the helium gas of mantle source. The $^{40}Ar/^{36}Ar$ ratios of hot spring water are in the range from $292.3{\times}10^{-6}\;to\;304.1{\times}10^{-6}$, implying the atmospheric argon source.

• The Journal of Small Business Innovation
• /
• v.19 no.2
• /
• pp.53-68
• /
• 2016

Motivation and activities for technological learning, entrepreneurship, innovation, and creativity are driving forces of economic development in Asian countries. In the early stages of technological development, technological learning and entrepreneurship are efficient ways in which to catch up with advanced countries because firms can accumulate skills and knowledge quickly at relatively low risk. In the later stages of technological development, however, innovation and creativity become more important. This study aims to identify a) the factors (learning capabilities) that influence technological learning performance and b) barriers to enhancing innovation capabilities for the creative economy and organizations. The major part of this study is related to learning capabilities in the post-catch-up era. Based on a literature review and observations from Korean experiences, this study proposes a technological learning model composed of various influencing factors on technological learning. Three hypotheses are derived, and data are collected from Korean machine tool manufacturers. Intense interviews with CEOs and R&D directors are conducted using structured questionnaires. Statistical analysis, such as correlation and ANOVA are then carried out. Furthermore, this study addresses how to enhance innovation capabilities to move forward. Innovation enablers and barriers are identified by case studies and policy analysis. The results of the empirical study identify several levels of firms' learning capabilities and activities such as a) stock of technology, b) potential of technical labor, c) explicit technological efforts, d) readiness to learn, e) top management support, f) a formal technological learning system, g) high learning motivation, h) appropriate technology choice, and i) specific goal setting. These learning capabilities determine firms' learning performance, especially in the early stages of development. Furthermore, it is found that the critical factors for successful technological learning vary along the stages of technology development. Throughout the statistical and policy analyses, this study confirms that technological learning can be understood as an intrinsic principle of the technology development process. Firms perform proactive and creative learning in the late stages, while reactive and imitative learning prevails in the early stages. In addition, this study identifies the driving forces or facilitating factors enhancing innovation performance in the post catch-up era. The results of the preliminary case studies and policy analysis show some facilitating factors such as a) the strategic intent of the CEO and corporate culture, b) leadership and change agents, c) design principles and routines, d) ecosystem and collaboration with partners, and e) intensive R&D investment.

• Journal of the Korean Geosynthetics Society
• /
• v.16 no.4
• /
• pp.231-240
• /
• 2017

Recently, there have been frequent occurrences of ground sink in the urban area, which have resulted in human and material damage and are accompanied by economic losses. This is caused by artificial factors such as soil loss, poor compaction, horizontal excavation due to the breakage of the aged sewage pipe, and lack of water proof at vertical excavation. The ground sink can be prevented by preliminary restoration and reinforcement through exploration, but it can be considered that it is not suitable for urgent restoration by the existing method. In this study, a model experiment was carried out to simulate the in-ground cavities caused by groundwater flow for developing non-excavation urgent restoration in underground cavity and the range of the relaxation zone was estimated by detecting the around the cavity using a relaxation zone detector. In addition, disturbance region and relaxation region were separated by injecting gypsum into cavity formed in simulated ground. The shape of the underground cavity due to the groundwater flow was similar to that of the failure mode III formed in the dense relative density ground due to water pipe breakage in the previous study. It was confirmed that the relaxed region detected using the relaxation zone detector is formed in an arch shape in the cavity top. The length ratio of the relaxation region to the disturbance region in the upper part of the cavity center is 2: 1, and it can be distinguished by the difference in the decrease of the shear resistance against the external force. In other words, it was confirmed that the secondary damage should not occur in consideration of the expandability of the material used as the injecting material in the pre-repair and reinforcement, and various ground deformation states will be additionally performed through additional experiments.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.14 no.12
• /
• pp.1102-1139
• /
• 2002

A review on the papers published in the Korean Journal of Air-Conditioning and Refrigerating Engineering in 2000 and 2001 has been done. Focus has been put on current status of research in the aspect of heating, cooling, ventilation, sanitation and building environment. The conclusions are as follows. (1) Most of fundamental studies on fluid flow were related with heat transportation of facilities. Drop formation and rivulet flow on solid surfaces were interesting topics related with condensation augmentation. Research on micro environment considering flow, heat, humidity was also interesting for comfortable living environment. It can be extended considering biological aspects. Development of fans and blowers of high performance and low noise were continuing topics. Well developed CFD technologies were widely applied for developing facilities and their systems. (2) Most of papers related with heat transfer analysis and heat exchanger shows dealt with convection, evaporation, and channel flow for the design application of heat exchanger. The numerical heat transfer simulation studies have been peformed and reported to show heat transfer characteristics. Experimental as well as numerical studies on heat exchanger were reported, while not many papers are available for the system analysis including heat exchanger. (3) A review of the recent studies on heat pump system shows that performance analysis and control of heat pump have been peformed by various simulations and experiments. The research papers on multi-type heat pump system increased significantly. The studies on heat pipe have been examined experimently for change of working characteristics and strut lure. Research on the phase change has been carried out steadily and operation strategies of encapsulated ice storage tank are reported experimentally in several papers. (4) A review of recent studies on refrigeration/air conditioning system have focused on the system performance and efficiency for new alternative refrigerants. Evaporation and condensation heat transfer characteristics are investigated for tube shapes and new alternative refrigerants. Studies on components of refrigeration/air conditioning system are carried to examine efficiency for various compressors and performance of new expansion devices. In addition to thermophysical properties of refrigerant mixtures, studies on new refrigerants are also carried out, however research works on two-phase flow seemed to be insufficient. (5) A review of the recent studies on absorption cooling system indicates that heat and mass transfer phenomena have been investigated to improve absorber performance. Various experimental data have been presented and several simulation models have been proposed. A review of the recent studies on duct and ventilation shows that ventilation indices have been proposed to quantify the ventilation performance in buildings and tunnels. Main efforts have been focused on the applications of ventilation effectiveness in practice, either numerically using computational fluid dynamics or experimentally using tracer gas techniques. (6) Based on a review of recent studies on indoor thermal environment and building service systems, research issues have mainly focused on many innovative ideas such as underfloor air-conditioning system, personal environmental modules, radiant floor cooling and etc. Also, the new approaches for minimizing energy consumption as well as improving indoor environmental conditions through predictive control of HVAC systems, various activities of building energy management and cost-benefit analysis for economic evaluation were highlighted.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.5 no.2
• /
• pp.136-142
• /
• 1985

For better grassland development in the forest, this field experiment was carried out to investigate the effect of thirteen different fertilizer levels of nitrogen(N), phosphorus ($P_2O_5$) and potassium ($K_2O$) on the botanical composition, growth and dry matter yield of grass-clover mixtures grown under trees with 40-50% of shading level. This experiment was arranged as a randomized block design with replications, and performed on the experimental field in the suburban forest of Suweon in 1984. The results obtained are summarized as follows: 1. Plant height and cover degree of grasses found to be high with 28 and 42kg N fertilizer per 10a, while those were the lowest with zero and N-zero fertilizer levels. The degree of bare land after the fourth cut was also high in the low N level. 2. A significant higher degree of leaf green and chlorophyll content of leaf blade was observed in the plot of 28 and 42 kg N per 10a when compared with low N fertilizer plot. However, leaf decay and plant type of grasses tended to be a little poor as the high N was applied. 3. the regrowth plant length and dry weight of grasses after the first cut increased significantly with 28 and 42 kg N fertilizer. However, those showed slightly increased regrowth in the plot of zero and N-zero fertilizer levels. 4. The dry matter yield of grasses was higher with 28 and 42 kg N than that of low N fertilizer level. Higher yields were obtained in the plot of standard ($N-P_2O_5-K_2O$=28-20-24 kg/10a), 50% increase of $N,P_2O_5K_2O$ and N-50% increase, although there were no significant differences among three fertilizer levels. 5. Growth, botanical composition, regrowth and yield of grasses grown under pine trees were significantly influenced by N fertilizer level, regardless of $P_2O_5\;and\;K_2O$. The fertilizer level of $N-P_2O_5-K_2O$ was 28-20-24 kg per 10a for more forage production in the forest. Considering economic yield in this study, however, the optimum fertilizer level of N, $P_2O_5\;and\;K_2O$ was suppose to be 21-28, 10-15, and 12-18kg per 10a, respectively.

• Korean Security Journal
• /
• no.41
• /
• pp.37-66
• /
• 2014

In recent years, with the development of computers and electronics, electronics and communication technology in a growing and each part is dependent on the cross-referencing makes all electronic equipment is obsolete due to direct or indirect damage EMP. Korea and the impending standoff North Korea has a considerable level of technologies related to the EMP, EMP weapons you already have or in a few years, the development of EMP weapons will complete. North Korea launched a long-range missile and conducted a nuclear test on several occasions immediately after, when I saw the high-altitude nuclear blackmail has been strengthening the outright offensive nuclear EMP attacks at any time and practical significance for the EMP will need offensive skills would improve. At this point you can predict the damage situation of Korea's security reality that satisfy the need, more than anything else to build a protective system of the EMP. The scale of the damage that unforeseen but significant military damage and socio-economic damage and fatalities when I looked into the situation which started out as a satellite communications systems and equipment to attack military and security systems and transportation, finance, national emergency system, such as the damage elsewhere. In General, there is no direct casualties reported, but EMP medical devices that rely on lethal damage to people who can show up. In addition, the State power system failure due to a power supply interruption would not have thought the damage would bring State highly dependent on domestic power generation of nuclear plants is a serious nuclear power plant accident in the event of a blackout phenomenon can lead to the plant's internal problems should see a forecast. First of all, a special expert Committee of the EMP, the demand for protective facilities and equipment and conduct an investigation, he takes fits into your budget is under strict criteria by configuring the contractors should be sifting through. He then created the Agency for verification of performance EMP protection after you have verified the performance of maintenance, maintenance, safety and security management, design and construction company organized and systematic process Guard facilities or secret communications equipment and perfect for the EMP, such as protective equipment maneuver system should take.

• Journal of the Korean Society of Costume
• /
• v.26
• /
• pp.175-206
• /
• 1995

The costume culture of China is as old and varied as her long history. As China is a multiracial nation and consists of fifty-six min-ority races including Han race, there are not only fifty-six different costumes in China but each races' costume habit is very different. Therefore, Chinese penninsula can be considered an enor-mous exhibition center of the costumes. This study undertook on the assumption that the costumes' mainstream of Korea and east-northern Asia as well as that of China could be examined by investigating the minority races' costumes in the east-and west-northern areas of China. The process of evolution of the costume of a particular people, country or area is subject not only to constraints related to geography such as climate, topography or local products but is also affected by numorous environmental influences including cultural, economic, social and even pol-itical ones in terms of the selection of material, styling, color and standard of tailoring. In other words, things like philosophy of life, religious be-lief, aesthetic outlook, moral code, class system, degree of affluence, and cultural exchange will all be reflected directly or indirectly by features of a people's or country's style costume. Of course, there are several factors affecting to the style of costume of the minority people in China. However, the only three factors-geo-graphical and environmental, production method, and religious belef-will be touched in this study. First of all, the geograghical and eenviron-mental factor would be the decisive one because the costume should be designed to overcome the constraints of climate and geographical environ-ments. Accordingly, each race has an unique style of costume. The costume of the minority races in the northern parts are loose and wide, and made of warm furs. For instance, Mongolian robe has the quality of anti-wind, anti-cold and warmness, and the width of a sleeve is narrow and long. Secondly, the costume style can be said to be limited by the production pattern, when the geo-graphical environment was affected to decide the costume style, the production pattern was together affected to it . In case of Mongolian robe, they should satisfy the dual condition as the practical function. One is the condition that they should be fitted to the climate, and the other is the condition that they should be suit-able to the nomadic life. Mongolian robes are suitable to the nomadic peoples because they are designed for not only overcoming the cold wind and weather but being used as the bedquit at night. The costumes of Hoche people was made of the skin of the fish and wild animals because of their main means of living being fishing and hunting. Accordingly, their costumes are dur-able, warm and water-proof. Finally, the style of the costume is affected by the religious belief. In other words, the pattern in fashion is closely related with the religious be-lief or ancestor worship and nature worship. Ac-cordingly, the symbols of these worship are often emerged in the decoration of the costume. The design of costume of the people in the northern areas of China is very simple. It is related with their monotheism. On the other hand, the costumes of twen쇼 minority races in the east-northern parts of China can be devided into three racial groups such as the long robes of Man people and Mongols, Tunics of the peoples in the west-northern areas, and the pants and jackets of Hoche people. The minorority races all has not only the unique costume habit but their costumes are also related with their living style and production means.