• Journal of the Korean Ceramic Society
• /
• v.32 no.3
• /
• pp.349-358
• /
• 1995

The ceramic composite membrane was synthesized by thermal oxidation after evaporation of Al on the support prepared by slip casting process. Oxidation was performed at $700^{\circ}C$ and 80$0^{\circ}C$ under dry oxygen atmosphere. It was considered as optimum oxidation condition that the membrane showed a knudsen behaviro. A further oxidation resulted in an increase of gas permeability because top layer became densified. Then, a multi-layered composite membrane was synthesized through a sol-gel method, evaporation and thermal oxidation of Al coating processes. While the membrane was thermally stable up to 80$0^{\circ}C$, gas permeability was rapidly decreased even at a slight amount of deposition of Al.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.11a
• /
• pp.75-76
• /
• 2012

In this study, it was evaluated about creep properties of high strength concrete according to compressive strength and moisture evaporation condition. As a results, creep strain and creep coefficient was greatly affected by moisture evaporation conditions rather than compressive strength. Also, the effect of fiber mixed was not show big difference.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.21 no.2
• /
• pp.294-302
• /
• 1997

Falling-film evaporation experiments for aqueous solution of lithium bromide (LiBr) were performed on a horizontal smooth 19.05-mm-dia copper tube. Average heat transfer coefficients were obtained with varied film Reynolds numbers, system pressures, LiBr concentrations and degrees of wall superheat. Heat transfer coefficients increase with increasing system pressure and decreasing concentration. For degrees of wall superheat, the heat transfer coefficient did not't show the distinct trend. For this experimental ranges, heat transfer coefficients showed maximum values at an optimal film Reynolds number. The results of this work were compared with pool boiling data reported previously, and it was shown that the heat transfer performance is superior to the pool boiling.

• Journal of Energy Engineering
• /
• v.11 no.1
• /
• pp.74-80
• /
• 2002

In this study, a numerical method for fuel droplet evaporation in cylinder of S.I. engine is presented. This study was newly defined non-dimensional critical droplet lifetime and modeled heating and evaporation processes of fuel droplet during intake and compression stroke of gasoline engine. The simulation results show that simultaneous increase of gas temperature and pressure in compression stroke seems to have compensative effect on droplet gasification rate. The environment variations in cylinder have little effect on the fuel droplet gasification process. The droplet size for full evaporation at the end of compression stroke can be estimated using this program.

• Journal of the Korean Ceramic Society
• /
• v.30 no.3
• /
• pp.175-180
• /
• 1993

Influence of Nd3+ substitution for Pb2+ on the dielectric properties and the PbO evaporation according to substituting Nd3+ for Pb2+ in Pb(Mg1/3Nb2/3)O3 system ceramics have been investigated. The dielectric constant at the curie temperature and evaporation of PbO were decreased with increase of Nd3+ amounts. The percentage of PbO evaporation was 2.5wt% in the PMN system substituted Nd3+ for Pb2+, while it was 3.7wt% in the PMN system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.4
• /
• pp.294-297
• /
• 2013

ZnO crystals with octahedral shape were synthesized by thermal evaporation technique. $ZnF_2$ powder was used as the source material. The thermal evaporation and oxidation of $ZnF_2$ powder was carried out for 1 hr at $1,000^{\circ}C$ in air under atmospheric pressure. SEM images showed that the ZnO crystals produced by oxidizing $ZnF_2$ vapor possessed a characteristic octahedral shape. XRD spectrum revealed that the ZnO octahedron had hexagonal wurtzite structure. In the room temperature photoluminescence spectrum, a strong green emission peak at around 510 nm was observed.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.192-198
• /
• 2004

A numerical study was conducted to determine the effects of high temperature air, including equivalent ratio on flow field, temperature, evaporation, and overall temperature distribution in gas turbine combustor. A sector model of a typical wall jet can combustor, featuring introduction of primary air and dilution air via wall jet, was used in calculations. Flow field and temperature distribution were analyzed. Operating conditions such as inlet temperature and overall equivalent ratio were varied from 373 to 1300 K, and from 0.3 to 0.6, respectively, while any other operating conditions were fixed. The RNG ${\kappa}-{\varepsilon}$ model and eddy breakup model were used for turbulence and combustion model respectively. It was found that the increase with the inlet air temperature, velocity in the combustor is accelerated and evaporation of liquid fuel is not affected in primary zone, high temperature inlet air enhances the evaporation and improves overall temperature distribution factor.

• Korean Journal of Human Ecology
• /
• v.22 no.1
• /
• pp.17-27
• /
• 2013

The purpose of this study is to investigate children's liquid conservation concept according to their ages and task-situations in the water evaporation phenomenon. Thirty from each 4-, 6- and 8-year-old age groups (total of 90 subjects) were selected for this study. The subjects were recruited from two day-care centers, a kindergarten, and an elementary school, in Seoul. Statistical methods used for data analysis were frequencies, percentiles, means, standard deviations and repeated measures ANOVA. As a result, there was a significant difference in children's liquid conservation concept in the evaporation of water according to their ages and task-situations. 8-year-old children showed levels of cognition than 4- and 6-year-olds. Children showed higher levels of cognition in the task of drying than in the task of water level changes.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.10 no.6
• /
• pp.674-682
• /
• 1998

In this study, thin film evaporation of water on low-fin tubes were experimentally investigated. Five low-fin tubes with different fin spacing and fin height were tested. Test range covered 0.146kg/ms $\leq$$\Gamma$$\leq$0.219kg/ms and 10㎾/$\m^2$$\leq$q $\leq$70㎾/$\m^2$. Saturation temperature was loot. Compared with the plain tube, low fin tubes enhanced the water film evaporation from 60% to 100%. Tubes with fin spacing smaller than 2mm and fin height higher than 1mm performed better than tubes with other fin configuration. However, when fin spacing was too small at high film flow or fin height was too high at low film flow, the performance decreased. The heat transfer coefficient slightly increased as the flow rate increased. Correlations are developed based on present data.

• Journal of the Korean Ceramic Society
• /
• v.47 no.2
• /
• pp.142-145
• /
• 2010

We made a film of a few ${\mu}m$ thickness by evaporating $As_2S_3$ piece to perpendicularly cut optical fiber by thermal evaporation process. Linear refractive index(n) and linear absorption coefficient(k) of amorphous $As_2S_3$ are 2.525 and $1.727{\times}10^{-3}$, respectively. A surface roughness did not exceed 2 nm and a transmission spectrum showed that the sample of thermal evaporation was homogeneous.