• Elastomers and Composites
• /
• v.24 no.2
• /
• pp.110-121
• /
• 1989

The radical initiated graft copolymerization of acrylonitrile(AN) and 4-chlorostyrene(4-Clst) onto ethylene-propylene-diene terpolymer(EPDM) rubber was investigated under various conditions. Graft copolymer(AU-EPDM-4-Clst) was isolated b: selective solvent extraction and identified by using IR spectroscopy. The percent grafting is determined as a function of solvent, reaction time, and monomer mole ratio. Percent grafting decreased in the order of tetrahydrofuran(THF)>THF/ethyl acetate(EA)(1 : 1)>cyclohexane/EA(1 : 1)>n-hexane/EA(1 : 1). Grafting increased continuously with increasing the reaction time up to 40 hr, beyond which the grafting levelled off. It was observed that percent grafting increased as increasing [4-Clst]/[AN] mole ratio, but decreased when [4-Clst]/[AN] mole ratio was higher than 1.60. The light resistance of graft copolymer(AN-EPDM-4-Clst) was better than that of ABS.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.449-452
• /
• 2009

In order to improve incombustibility of EPDM(Ethylene propylene diene monomer)-based rubber, inorganic materials as $Al(OH)_3$ and $Sb_2O_3$ were added. The mechanical and thermal properties have been measured for vulcanized rubber loaded with different concentrations of $Al(OH)_3$ and $Sb_2O_3$. As inorganic material contents increases from 5phr to 30phr, the specific gravity and hardness increase while elongation at break decreases. This study performed incombustibility test and thermal analysis through TGA(Thermogravimetric Analyzer). As a results, incombustible and thermal properties of EPDM-based rubber were improved as $Al(OH)_3$ and $Sb_2O_3$ contents increase.

• Elastomers and Composites
• /
• v.16 no.1
• /
• pp.3-13
• /
• 1981

The purpose of this dissertation is to study the physical properties of cellular rubber products for industrial use. Vulcanization characteristics were investigated by usingcure curve that had obtained by means of Rheometer. The results of physical properties, vulcanization characteristics and foaming states are as follows. 1. The test results for vulcanization characteristics of NR compounds indicated that in the recipe R-1. When accelerator D is used, the optimum conditions of vulcanizate are obtained, while formula R-2 and R-3 have shown higher torgue at curing time, $1{\sim}2$ minutes. Cellular rubber product test in terms of compression set and compression deflection has also met the requirements of SAE. 2. For SBR compounds, S-1 formula was the best in terns of vulcanization characteristics, and for the blowing structure of cellular rubber products, formula S-3 in which accelerator M is added was fair. All other test results, such as compression set and compression deflection properties met SAE requirements. 3. NBR compound (N-1) including accelerator TT was the best in terms of vulcanization characteristic and also blowing structure. All other properties listed above met requirements, particulary for oil resistance test. 4. In the test of EPDM compounds, when mixed accelerator, M and TT, is used(formula E-1) the best results were obtained. Since EPDM is hydrocarbon elastomer, oil resistance test failed. All other properties met the requirement specified in SAE.

• Elastomers and Composites
• /
• v.53 no.2
• /
• pp.80-85
• /
• 2018

Chloro isobutylene isoprene rubber (CIIR) and ethylene propylene diene monomer (EPDM) compounded with other formulation chemicals, depending on the polymer blend, were prepared by mechanical mixing. After manufacturing the rubber vulcanizate by compression molding with a hot press, the mechanical and thermal properties including thermal conductivity, rebound resilience of the CIIR/EPDM blends were measured. As the EPDM rubber content increased, hardness and tension set showed a tendency to increase. Pure CIIR exhibited the lowest tensile strength; however, tensile strength increased with loading of EPDM rubber. On the other hand, in CIIR rubber, which is usually a low-rebound elastomer owing to a high damping effect, rebound resilience exhibited an increasing trend as the content of EPDM rubber increased. As the EPDM rubber content increased, thermal stability was improved due to reduction of decomposition rate in the rubber region of the blend vulcanizate.

• Elastomers and Composites
• /
• v.50 no.4
• /
• pp.245-250
• /
• 2015

Recycling of ethylene-propylene-diene terpolymer (EPDM) scrap was tried by blending with polypropylene (PP). EPDM scrap powder was prepared by shear pulverization process at high temperature, which may lead to selective chain scission induced by difference in the critical elastic coefficient. On the other hand, EPDM scrap powder was prepared by adding a selected reclaiming agent during shear pulverization process at high temperature. Terpene as a bonding agent was then introduced to improve adhesion property. PP, used as a matrix for manufacturing thermoplastic elastomer, was modified by the incorporation of dicumyl peroxide and maleic anhydride. The functionalized EPDM and modified PP were blended and cured dynamically at $190^{\circ}C$. The blend materials prepared in this study showed the comparable results to those of conventional TPE in terms of tensile and flow properties. Also, the odor component of recycled EPDM was analyzed using GC-MS.

• Elastomers and Composites
• /
• v.5 no.2
• /
• pp.155-164
• /
• 1970

• Elastomers and Composites
• /
• v.9 no.2
• /
• pp.136-139
• /
• 1974

• Elastomers and Composites
• /
• v.29 no.4
• /
• pp.360-367
• /
• 1994

• Elastomers and Composites
• /
• v.27 no.3
• /
• pp.215-223
• /
• 1992

• Elastomers and Composites
• /
• v.13 no.1
• /
• pp.51-55
• /
• 1978