• Journal of Veterinary Clinics
• /
• v.24 no.2
• /
• pp.201-207
• /
• 2007

The teat cup liner compounds with improved physical property were developed using tri-polymer blend of natural rubber(NR), ethylene propylene diene monomer rubber(EPDM) and butyl rubber, and the changes of the physical properties of compounds were measured under various conditions such as standard, thermal, alkaline detergent and acid solutions aging conditions. The hardness of the new teat cup liner compound 1 was 50 and that of the compound 2 was 51 under standard condition. The tensile strength and elongation of the new compound 1 were $154kgf/cm^2$ and 675% under the standard condition, respectively. Also, those of the new compound 2 were 180 kgf/cm and 634% under the same condition. Their hardness were increased about $2{\sim}6%$ and the tensile strength and elongation were decreased about 10% under the $25^{\circ}C$ water and detergent solutions. Even though the new teat cup liner compounds exhibited so much decreased tensile properties under the $105^{\circ}C$ thermal aged condition, they sustained more stable aged physical properties including tensile strength and elongation than those of imported teat cup liner materials. Consequently, the new teat cup liner compounds would give prolonged lift cycle if they are used as a teat cup liner product.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.38 no.5
• /
• pp.93-101
• /
• 2010

The demand for elastic pavement, providing comfort for pedestrians is expected to increase continuously but the lack of a standard for materials mixing ratio, that is, the optimal mixing ratio between ERDM chip and polyurethane binder, is still in a trial and error stage. This study aimed at recommending an optimal mixing ratio for elastic landscape pavement through a coherence and resilience test depending on ratio. The test result is outlined as follows. In a tensile strength test, samples B and C indicated a close positive relationship between the binder mixing ratio and tensile strength, indicating that the higher the mixing ratio the higher the tensile strength. In a hardness test, none of samples A, B or C indicated a statistical interrelationship between the binder mixing ratio and hardness. That is, the hardness of the elastic pavement material remained unchanged, irrespective of the binder mixing ratio. In a resilience lest, Samples A and B indicated a close negative interrelation between mixing ratio and resilience, indicating that the higher the mixing ratio, the lower the resilience. Upon analyzing the optimal mixing ratio based on test results, an increase in tensile strength began to slow at a 20% mixing ratio, while resilience began to reduce rapidly at 22%, Thus the optimal range for a mixing ration appeared to be 20~22%. The outcome of this study could to provide guidance for improving the elasticity and stability of elastic pavement.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.24 no.2
• /
• pp.61-68
• /
• 2006

Rubber rollers in off-set printing process are one of the most important factor, transferring the ink and water to the plate. Each different roughness of roller surface and different rubber compounds could effect to ink transparency and printability. Three different rubber compounds (NBR, EPDM, PU) and each different roughness of roller surface would show us different result of ink transparency and density of actual printing result. There might be a differences from actual printing result not only the amount of transferred ink, but there is also some other point we should check it out. According to the result of this studies, we found that different rubber compounds and their surface roughness directly effect to the rate of ink transfer. It also shows that the amount of transferred ink is not even and stable amount what we expect to get optimum printability. To reach a targeted printability with rollers, firstly it is necessary to choose correct rubber compounds with certain purpose and the roughness of roller surface has to be as smooth as less than $5{\mu}m{\sim}7{\mu}m$.

• Elastomers and Composites
• /
• v.44 no.1
• /
• pp.22-33
• /
• 2009

Recently, elastomer-nanocomposites reinforced with low volume fraction of nanofillers have attracted great interest due to their fascinating properties. The incorporation of nanofillers, such as, layered silicate clays, carbon nanotubes, nanofibers, calcium carbonate, metal oxides or silica nanoparticles into elastomers improves significantly their mechanical, thermal, dynamic mechanical, barrier properties, flame retardancy, etc. The properties of nanocomposites depend greatly on the chemistry of polymer matrices, nature of nanofillers, and the method in which they are prepared. The uniform dispersion of nanofillers in elastomer matrices is a general prerequisite for achieving desired mechanical and physical characteristics. In this paper, current developments in the field of elastomer nanocomposites reinforced with layered silicates, silica, carbon nanotubes, nanofibers and various other nanoparticles have been addressed.

• Elastomers and Composites
• /
• v.15 no.3
• /
• pp.147-154
• /
• 1980

The cellular rubber products for industrial purpose have been applied in many fields such as auto-motive parts, ship-building, machinery, sports goods, diving suit or interior housings etc. The purpose of this dissertation is to study the physical properties of celluar rubber products particulary for those elastomers such as EPDM, CR and NBR with heat resistance property, weather proofness, and oil resistance characteristics respectively, aiming at improving their quality, and renovating the manufacturing know-how which is beyond our technical power at the present time in Korea. In order to meet this requirement an ideal recipe is being shown for the three elastomers, and also a practical recipe which is easily available in terms of compounding ingredients in domestic market has set up as shown in Table 1. for the investigation of vulcanization characteristics by means of Rheometer. The optimum Mooney viscosity of compounded rubber was found to be approximately $ML_{1+4}(100^{\circ}C)$ $30\sim45$. Excess mustication makes a dispersion of ingredients worse, consequently it causes deformation of shapes and heterogenous cell distribution. In other words the articles are rejected because of its insufficient workmanship. The results of physical properties of the products are indicated in Table 3. It has shown that the quality meet requirement when tested in accordance with ASTM D572, 573 and D 395. The test results o CR/IR blends in terms of hardness, volume change by blowing, tensile strength and elongation have been shown.