• Nuclear Engineering and Technology
• /
• v.52 no.11
• /
• pp.2511-2521
• /
• 2020

The Fukushima accident is characterized by the fact that three reactors at the same site experienced reactor vessel failure and the accident resulted in significant radiological release to the environment, which was about 1/10 of the Chernobyl releases. The safe removal of fuel debris in the reactor vessel and Primary Containment Vessel (PCV) and treatment of huge amount of contaminated water are the major issues for the decommissioning in coming decades. Discussions on the new researches efforts being carried out in the area of investigation of the end state of fuel debris and Boling Water reactor (BWR) specific core melt progression, development of technologies for the mitigation of radiological releases to comply with the strengthened safety requirement set after the Fukushima accident are discussed.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.50 no.3
• /
• pp.146-152
• /
• 2001

This paper describes an accurate fault location algorithm based on sequence current distribution factors for a double-circuit transmission system. The proposed method uses the voltage and current collected at only the local end of a single-circuit. This method is virtually independent of the fault resistance and the mutual coupling effect caused by the zero-sequence current of the adjacent parallel circuit and insensitive to the variation of source impedance. The fault distance is determined by solving the forth-order KVL(Kirchhoff's Voltage Law) based distance equation. The zero-sequence current of adjacent circuit is estimated by using a zero-sequence current distribution factor and the zero-sequence current of the self-circuit. Thousands of fault simulation by EMTP have proved the accuracy and effectiveness of the proposed algorithm.

• Asia pacific journal of information systems
• /
• v.4 no.2
• /
• pp.83-130
• /
• 1994

Software development of large scale program such as Operating System or University Total Information System is lengthy and costly process. In order to reduce cost, time and risk, there is currentry general acceptance of the need for Software Reuse System during the whole development cycles. In this paper, (from a practical point of view), the problem of existing reuse system methodology is analyzed and an implement method of software reuse system is presented. Also using this method Application Program Reuse System(APRS) which supports all phase of software life cycles is designed and implemented. This application program reuse system which is based on common language is considerably shown to reduce communication Error of requirement specification between systems analyst and end-user.

• Journal of the Korean Society for Precision Engineering
• /
• v.18 no.6
• /
• pp.87-92
• /
• 2001

An error analysis is very important for a precision machine to estimate its performances. This study proposes a new parallel device, cubic parallel manipulator. Errors of the proposed cubic parallel manipulator include upper and down universal joint errors, due to the directional changes in the forces in the links, and actuation errors. An error analysis is presented based on an error model formed through the relation between the universal joint errors of the cubic parallel manipulator and the end effector accuracy. The analysis shows that the method can be used in predicting the accuracy of other cubic parallel devices.

• Proceedings of the KSRS Conference
• /
• 2005.10a
• /
• pp.104-107
• /
• 2005

COMS(Communication, Ocean, and Meteorological Satellite) is the geostationary satellite for the mission of satellite communication, ocean monitoring, and meteorological service. It is scheduled to be launched at the end of 2008. Ocean payload of COMS named as GOCI(Geostationary Ocean Color Imager) observes ocean color and derives the chlorophyll concentrlition, the concentration of dissolved organic material and so on. In operational oceanography, satellite derived data products are used to provide forecasting and now casting of the ocean and coastal water state. In this work, conceptual design of structural part of GOCI is carried out and two baseline concepts are proposed. The one is dioptric module that uses lens system and the other is TMA(Three Mirror Anastigmat) module that uses mirror system. Trade-off studies between two concepts are investigated by considering optical and mechanical performances. Finally, on-going tasks and future development plan are briefly discussed.

• Proceedings of the Korean Society of Agricultural Engineers Conference
• /
• 2003.10a
• /
• pp.191-194
• /
• 2003

The purpose of this paper was to derive soil-water characteristic curve equation for unsaturated soil. To this end, a series of suction measured test was conducted on the selected 4 kinds of soil which is located in Korea, used the modified pressure plate apparatus. From the test results, it was proved that characteristic curve changes according to grain size distribution, size of void and fine grained soil contents. Residual degree of saturation(Sr) was decreased with void ratio and changed with fine grained soil contents, parameter ${\lambda}$ and hr was increased with void ratio. Soil-water characteristic curve equation based on the test result was suggested by void ratio or grain size distribution.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2154-2159
• /
• 2005

This paper presents the kinematic analysis of two robots, an exoskeleton type master robot and a human like slave robot with two arms. Two robots are designed and built to be equivalent as motion following robots. The operator wears the exoskeleton robot to generate motions, then the slave robot is required to follow after the motion of the master robot. However, different kinematic configuration yields position mismatches of the end-effectors. To synchronize motions of two robots, kinematic analysis of mapping is analyzed. The forward and inverse kinematics have been simulated and the corresponding experiments are also conducted to confirm the proposed mapping analysis.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.2071-2075
• /
• 2003

Pressure variation is one of the major sources on noise emission in the oil hydraulic piston pumps. Therefore, it is necessary to clarify about pressure variation characteristics of the oil hydraulic piston pumps to reduce noise. Pressure variations in a cylinder at trapping region were measured during pump working period with discharge pressures, rotational speeds. The effect of pre-compression of the discharge port with three types valve plates also investigated. It was found that the pressure variation characteristics of oil hydraulic piston pumps deeply related with pre-compression design of the discharge port. Also, it was found that the pressure overshoot at trapping region can reduce by use of pre-compression at the end of the discharge port in valve plate

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.5 no.1
• /
• pp.177-190
• /
• 2011

The purpose of this study is to explore the determinants of actual demand for wireless broadband (WiBro) services in Korea. To this end, this study identifies conceptual definitions of diverse latent variables and determines the significance of the causal relationship between independent and dependent variables. It then presents the nomadic user concept by testing the moderator effect. This study also proposes a revised Unified Theory of Acceptance and Use of Technology (UTAUT) model, which is an appropriate model for wireless communication services and users' attributes. Prior research has concentrated exclusively on the Technology Acceptance Model (TAM) based on future potential users. Compared to previous studies, the current research model and analysis results are useful in not only academic but also industry contexts.

• Journal of Multimedia Information System
• /
• v.5 no.4
• /
• pp.291-297
• /
• 2018

Performance measurement is not an easy task. However, it is necessary to measure the expected value of the informatization project to be invested, to help the successful progress of the informatization project, and to confirm the result of the informatization project. This study describes the evaluation systems of the defense informatization project in Korea used after the end of the informatization project (post-implementation evaluation stage). In the post-implementation evaluation stage of proposed system, the informatization project is evaluated in terms of performance achievement, project plan compliance, project management, and economic validity. For each element, this study suggests metrics and practical measurement method. With metrics and their method, it can be evaluated which project is better than others. Moreover, the lessons learned can be developed. Under scarce budget condition, defense organizations can make better performance from IT project with the evaluation system suggested in this study.