• 전력전자학회논문지
• /
• 제6권6호
• /
• pp.546-555
• /
• 2001

본 논문에서는 PWM 인버터-유도전동기 구동시스템의 전도노이즈 저감을 위한 출력필터 설계에 관한 연구를 수행하였다. 전도노이즈는 고전압 입력, 고용량 구동시스템 그리고 긴 전동기 터미널 등의경우에서 크게 문제가 된다. 고압력을 갖는 시스템에서는 높은 압력에 비례한 직류 링크 전압을 갖고 이에 따라 스위칭 dv/dt가 순간 최대 CM 접지전류를 발생시킨다. 그러므로 이에 대한 대책이 필요하다. 따라서 최근 산업 현장에서 많이 사용되고 있는 PWM 인버터를 설계 제작하여 유도전동기를 구동하고 이에 따라 발생되는 전도노이즈 성분을 감쇠 시킬 수 있는 출력필터를 설계하였고 제작 및 실험을 통하여 그 타당성을 입증하였다.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2011년도 춘계학술논문집 1부
• /
• pp.385-388
• /
• 2011

The electromagnetic wave occurs primarily LED lighting equipment in the interior medical imaging information a lot of high-frequency equipment environment installation. It generated by lighting fixtures mach damage to patients as well as non or no operation. It can be reduced through noise attenuation and filter change. It associated with the capacitors and inductors can reduce by are used frequency efficiently, Attenuation circuit does not significantly affect the radiation medical equipment devices

• 한국자동차공학회논문집
• /
• 제22권3호
• /
• pp.143-147
• /
• 2014

The ECU which is operating inductive actuator like motor or solenoid should be designed with considering the heat removal performance and the EMC performance. In most cases, these two performances are trade-off. Especially, the metal cover with plastic housing for improving heat removal performance can affect EMC performance by coupling the noise source to harness cable and connector. Therefore, after analyzing the EMC effectiveness of the metal cover, countermeasures for EMC noise reduction should be established. In this paper, by simulating and testing of AHB Gen3 ECU, the influence of the metal cover to EMC performance is analyzed. And based on this result, we propose solutions for EMC noise reduction.

• 한국전자파학회논문지
• /
• 제14권3호
• /
• pp.233-238
• /
• 2003

고속 회로의 발전과 함께 고주파 잡음의 발생 가능성이 커지고, 이러한 시스템의 잡음 억제를 위해 다중 접지(multipoint ground)가 사용되고 있다. 이 가운데 스크류를 이용한 인쇄회로기판의 접지는 인접 스크류들 사이에 접지 루프를 형성하여 방사잡음을 유발한다. 본 논문에서는 이러한 문제를 해결하기 위하여 기구물(chassis)에 대한 인쇄회로기판의 접지 구조를 제안하였다. 제안된 구조는 전파흡수체와 전도성 구리 테이프를 이용해서 전파 흡수량을 증가시킨 것이다. 1~3 ㎓대역에서 기판의 방사 잡음을 측정한 결과, 제안된 접지 구조는 스크류 접지 구조에 비해 2 ㎓ 이하의 대역에서 방사 잡음이 2.62 dBuV/m 감소되었다.

• 한국항공우주학회지
• /
• 제34권4호
• /
• pp.102-109
• /
• 2006

본 논문에서는 검증위성(KoDSat)의 시스템 레벨 전자기파(EMC) 환경시험 및 전자기파(EMC) 규격을 초과한 시험결과에 대해서 발사체에 대한 영향성 분석 및 하드웨어 개선 방법에 대하여 논하고, EMC2000 소프트웨어 해석을 통해 KSLV-1 발사체의 비행종단시스템(FTS : Flight Termination System)에 영향을 줄 수 있는 검증위성의 전자기파 노이즈원을 도출하였다. 또한 도출된 전자기파(EMC) 노이즈원은 EMI 필터, 접지, 쉴딩(Shielding) 처리 기법을 데이터획득장치(DAU) 전력보드(Power Board)에 적용하여 미약한 값으로 제거되었다. 그리고 이와 같은 일련의 분석과정에 의해 새로 설계된 전력보드는 검증차원에서 데이터획득장치(DAU)에 장착되어 박스자체 전자기파(EMC) 시험 및 최종 2차 검증위성 시스템 레벨 전자기파 시험을 통해 확인되었고, 측정 결과는 저주파대역과 UHF 주파수대역(430Mhz)에서 만족할 만한 감쇄레벨 값을 나타내었다.

• 전기학회논문지
• /
• 제62권9호
• /
• pp.1329-1334
• /
• 2013

A electric railway is unique system that electric trains consumed huge electric power are travelled and is much interested with EMC. There were several problems exceeding the standard in the frequency range of 9kHz to 150kHz because the radiation noises were moved the higher frequency range according to developing the power electronic technology. It is studied the experimental confirmation of main noise source on the electric train and the analytic simulation for reducing the noise level in this paper.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 학술대회 논문집 전문대학교육위원
• /
• pp.98-101
• /
• 2002

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. These features are brought by the ON-OFF operation of semiconductor switching devices. However, this switching operation causes the surge and EMI(Electromagnetic Interference) which deteriorate the reliability of the converter themselves and entire electronic systems. This problem on the surge and noise is one of the most serious difficulties in AC-to-DC converter. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. A RPWM control method was proposed in order to smooth the switching noise spectrum and reduce it's level. Experimental results are verified by converter operating at 300V/1kW with 5%${\sim}$30% white noise input. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with USN. which are connected to the spectrum analyzer respectively.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(2)
• /
• pp.793-797
• /
• 2003

Switching PFC converters are widely used not only to comply the power quality specification but also for maximum efficiency. However switching PFC converters generate serious electromagnetic interference (EMI). In this paper to solve this problem, we applied the APW(Anti Phase Winding) and RPWM(Ran-dom PWM) technique to PFC boost converter and obtained satisfactory results. Simulation and experimental results show the improved harmonic and reduced EMI effect in air-conditioner system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술대회 논문집 전문대학교육위원
• /
• pp.79-82
• /
• 2003

The switching-mode power converter has been widely used because of its features of high efficiency and small weight and size. In the switching-mode power converter, the output voltage is generally controlled by varying the duty ratio of main switch. When a converter operates in steady state, duty ratio of the converter is kept constant. So the power of switching noise is concentrated in specific frequencies. The more white noise is injected, the more conducted EMI is reduced. But output-voltage is not sufficiently regulated. This is the reason why carrier frequency selection topology is proposed. In the case of carrier frequency selection, output-voltage of steady state and transient state is fully regulated. Spectrum analysis is performed on the Phase current and the CM noise voltage. The former is measured with Current Probe and the latter is achieved with LISN, which are connected to the spectrum analyzer respectively.

• Journal of Electrical Engineering and Technology
• /
• 제13권1호
• /
• pp.532-532
• /
• 2018

This article has been retracted at the request of the authors and/or the Editor in Chief. Reason: After the paper published, the authors have found that the intellectual property for this paper was a company's own. As a result, the authors have elected to withdraw the complete article with apologies to the scientific community