• Journal of Advanced Marine Engineering and Technology
• /
• 제23권1호
• /
• pp.25-32
• /
• 1999

This study was carried out to reduce NOx emissions from diesel engine and to investigate the variation of engine performance using the water injection. In this study the water was extracted from the exhaust gas and injected directly into the intake port with the inlet charge. The water condensing system operated as a closed system without any supplementary water supply. The experimental parameters such as the revolution the torque and the water injection rate are varied and the result from this experiment found the significant NOx reduction whereas the smoke emission increases as water/air ratio increases as the cases like the EGR. In spite of increasing the quantity of the water injection the engine output was slightly decreased and the specific fuel consumption was increased as was anticipated. Especially the system was founded to be effective on the reduction of the NOx emissions at the high load region relatively.

• 한국자동차공학회논문집
• /
• 제9권4호
• /
• pp.85-91
• /
• 2001

LPG has been well known as a clean alternative fuel for vehicles. As a fundamental study on liquid phase LPG injection (hereafter LPLI) system application to heavy-duty engine, engine output and combustion performance were investigated with various operating conditions using a single cylinder engine equipped with the LPLI system. Experimental results revealed that no problems were occurred in application of the LPG fuel to heavy-duty engine, and that volumetric efficiency and engine output, by 10% approximately, were increased with the LPLI system. It was resulted from the decrease of the intake manifold temperature through liquid phase LPG fuel injection. These results provided an advantage in the decrease of the exhaust gas temperature, in the control of knocking phenomena, spark timing and compression ratio. The LPLI engine could normally operated under $\lambda$=1.5 or EGR 30% condition. The optimized swirl ratio for the heavy duty LPG engine was found around R_s$ = 2.0.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.88-97
• /
• 2013

This paper presents a robust air-to-fuel ratio (AFR) control algorithm for managing exhaust gas recirculation (EGR) systems. In order to handle production tolerance, deterioration and parameter-varying characteristics of the EGR system, quantitative feedback theory (QFT) is applied for designing the robust AFR control algorithm. A plant model of EGR system is approximated by the first order transfer function plus time-delay (FOPTD) model. EGR valve position and AFR of exhaust gas are used as input/output variables of the plant model. Through engine experiments, parameter uncertainty of the plant model is identified in a fixed engine operating point. Requirement specifications of robust stability and reference tracking performance are defined and these are fulfilled by the following steps: during loop shaping process, a PID controller is designed by using a nominal loop transmission function represented on Nichols chart. Then, the frequency response of closed-loop transfer function is used for designing a prefilter. It is validated that the proposed QFT-based AFR control algorithm successfully satisfy the requirements through experiments of various engine operating points.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.301-310
• /
• 2003

Eco-Machinery engineering technologies in KIMM for reducing NOx emission were introduced. Combustion technologies such as reburning and fuel staged or air staged combustion have been applied to reduce NOx emission in the field of boiler furnaces. Lean premixed combustion method have been studied in gas turbine combustor. Hybrid system with plasma and SCR being considered as prospective method of De-NOx has been developed. Also, low NOx technologies including common rail system, EGR and DPF in diesel engine have been investigated.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2017년도 특별논문집
• /
• pp.54-58
• /
• 2017

The vessels which are operated in ECA (Emission Control Area) after $1^{st}$ January 2016 shall be complied with revised NOx emission requirement (Tier III). Effective solutions for NOx emission requirement are SCR (Selective Catalytic Reduction), EGR (Exhaust Gas Recirculation) and Installation of LNG Dual Fuel Engine. This study is considered the design modification as per application of LNG Ready notation. In case of LNG Ready - S notation, the vessel shall be retrofitted the Main engine with Dual fuel engine and LNG Fuel system after delivery. On this paper, the entire process for design modification was explained to meet the requirement for LNG Ready notation.

• 한국공작기계학회논문집
• /
• 제12권6호
• /
• pp.104-111
• /
• 2003

In order to collect the engine performance data and determine optimum engine conditions, engine performance test based on interface unit were tested This paper was carried out that engine' performance was developed using interface unit between personal computer and diesel engine. The results of the study are summarized as follows: Interface unit was developed. By using PAL, simulation was carried in order to logic's inspection. From this tea NO$_{x}$ were decreased, otherwise PM were increased. By using EGR system PM were increased by twice in the high load ranges, it was not seen to come into effect in the low load ranges. This system was tested D-l3 mode, the results were decreased more than 50% in the NO$_{x}$ emission.

• 대한안전경영과학회지
• /
• 제16권3호
• /
• pp.185-194
• /
• 2014

Internal engine is the main power source of vehicle and is the main source of air pollution. To satisfy this getting rigorous emission regulation, it must be solved simultaneously the dilemma of reducing emission gas and increasing heat efficiency. Diesel engine is preferred compare with gasoline engine in aspect of energy consumption but it must be solved reducing the containing of NOx, CO and HC. In this study: 1. Looking for alternative of performance improvement of Exhaust Gas Recirculation(EGR) which is emission gas reduction system. 2. Reducing malfunction of controlling emission gas. 3. Made possible precision control.

• 한국분무공학회지
• /
• 제19권4호
• /
• pp.204-210
• /
• 2014

Experimental study was conducted to investigate the effect of EGR(exhaust gas recirculation) on engine noise using single cylinder combustion ignition engine. Under constant engine rotary speed of 1200 RPM, 8 mg fuel quantity was injected with 15, 18 and 21% of oxygen ratio and 1400 bar of injection pressure. Using the in-cylinder pressure data acquired by a piezoelectric transducer, the engine performance parameters were calculated. Radiated engine noise measured for 10 seconds was analyzed using spectral characteristics and sound quality metrics such as loudness, sharpness, roughness. From the obtained engine performance parameters and sound quality metrics, effect of oxygen ratio of the premixed air, start of injection timing on frequency characteristic and sound quality metrics were analyzed. Correlation analysis was conducted between MPRR(maximum pressure rise rate), RI(ringing intensity) and sound quality metrics. RI was identified as the most important factor having influence on the sound quality metrics.

• 한국가스학회지
• /
• 제22권2호
• /
• pp.78-83
• /
• 2018

이 논문은 디젤엔진 자동차의 EGR 및 공기 제어와 CPF 장치에 관련된 고장사례 연구이다. 첫 번째 사례는 엔진진공펌프 손상으로 인해 엔진오일이 EGR 밸브 내부 다이어프램 손상으로 인해 오일이 흡기로 유입되어 연소실로 들어가 불완전 연소함으로써 배기할 때 매연이 발생된 것으로 확인되었다. 두 번째 사례의 원인은 공기제어 장치인 스로틀 플랩(throttle flap)을 점검하였을 때 스로틀 플랩이 고착되어 흡입공기량 부족에 의해 매연이 발생된 것을 확인하였다. 세 번째 사례는, 배기가스 온도센서의 불량으로 인해 온도를 감지하지 못해 재생기능이 되지 않아 매연이 발생된 것으로 확인되었다. 따라서, 배기가스발생으로 인한 환경오염 문제가 발생하지 않도록 최적의 상태를 유지하도록 관리하여야 한다.

• 한국자동차공학회논문집
• /
• 제19권5호
• /
• pp.134-142
• /
• 2011

Although combustion is essential in most energy generation processes, it is one of the major causes of air pollution. Exhaust pipes with circular fin were designed to study the effect of cooling the recirculated exhaust gases (EGR) of Diesel engines on the chemical composition of the exhaust gases and the reduction in the percentages of pollutant emissions. The gases examined in this study were oxides of nitrogen (NOx), carbon dioxide ($CO_2$) and carbon monoxide (CO). In addition, $O_2$ concentration in the exhaust was measured. The designs adopted in this study were about exhaust pipes with solid and hollow fins around them direct surface force measurement in water using a nano size colloidal probe technique. The direct force measurement between colloidal surfaces has been an essential topic in both theories and applications of surface chemistry. As particle size is decreased from micron size down to true Carbon nano Colloid size (<10 nm), surface forces are increasingly important. Nano particles at close proximity or high solids loading are expected to show a different behavior than what can be estimated from continuum and mean field theories. The current tools for directly measuring interaction forces such as a surface force apparatus or atomic force microscopy (AFM) are limited to particles much larger than nano size. This paper use Water and CNC fluid at normal cooling system of EGR. Experimental result showed all good agreement at Re=$2.54{\times}10^4$ by free convection and Re=$3.36{\times}10^4$ by forced air furnace.