• Journal of Korean Society for Atmospheric Environment
• /
• v.20 no.5
• /
• pp.615-623
• /
• 2004

This study was conducted for developing the emission factors of nitrogen oxide(NOx) and carbon monoxide (CO) from the combustion boilers burning liquefied natural gas (LNG). These emission factors were compared with those of U.S. EPA and European Environment Agency (EEA). NOx and CO concentration in the flow gas were measured using Kane-May, KM9106 and Thermo Environmental Instruments Inc., 42C-HL. Measurement were conducted at thirty industrial and commercial LNG boilers. Emission factors were calculated on the basis of fuel consumption (kg-pollutant/㎥-fuel burned). NOx concentration at industrial boiler was 14~125 ppm and it was measured as 35~125 ppm at commercial boiler. NOx emission factors of industrial boiler and commercial boiler were 1.84kg/$m^3$ and 2.09kg/$m^3$, respectively. NOx emission factor of commercial boiler was higher than that of industrial boiler. The NOx emission factors estimated in this study were lower than those of U.S. EPA and higher than those of EEA. Average CO emission factor of industrial boiler was 0.65 kg/$m^3$ and at commercial boiler it was 0.70kg/$m^3$, CO emission factor at industrial boiler was lower than that at commercial boiler.

• Journal of Ecology and Environment
• /
• v.33 no.3
• /
• pp.261-270
• /
• 2010

Increasing atmospheric $CO_2$ affects the soil carbon cycle by influencing microbial activity and the carbon pool. In this study, the effects of elevated $CO_2$ on extracellular enzyme activities (EEA; ${\beta}$-glucosidase, N-acetylglucosaminidase, aminopeptidase) in salt marsh sediment vegetated with Suaeda japonica were assessed under ambient atmospheric $CO_2$ concentration (380 ppm) or elevated $CO_2$ concentration (760 ppm) conditions. Additionally, the community structure of sulfate-reducing bacteria (SRB) was analyzed via terminal restriction fragments length polymorphism (T-RFLP). Sediment with S. japonica samples were collected from the Hwangsando intertidal flat in May 2005, and placed in small pots (diameter 6 cm, height 10 cm). The pots were incubated for 60 days in a growth chamber under two different $CO_2$ concentration conditions. Sediment samples for all measurements were subdivided into two parts: surface (0-2 cm) and rhizome (4-6 cm) soils. No significant differences were detected in EEA with different $CO_2$ treatments in the surface and rhizome soils. However, the ratio of ${\beta}$-glucosidase activity to N-acetylglucosaminidase activity in rhizome soil was significantly lower (P < 0.01) at 760 ppm $CO_2$ than at 380 ppm $CO_2$, thereby suggesting that the contribution of fungi to the decomposition of soil organic matter might in some cases prove larger than that of bacteria. Community structures of SRB were separated according to different $CO_2$ treatments, suggesting that elevated $CO_2$ may affect the carbon and sulfur cycle in salt marshes.

• Journal of Korean Society of Environmental Engineers
• /
• v.33 no.4
• /
• pp.223-230
• /
• 2011

According to EMEP/EEA Emission Inventory Guidebook, the emissions produced by vehicle in cold start phase should be calculated differently compared to hot start phase. In this study, considering this driving cycle, more appropriate procedures for estimating Environmental Benefits was suggested. Using Tier 3 standard, all links within the impact area were included in estimating emissions. Traffic volume and travel distance were analyzed using EMME/3 software. For application of the procedures in this study, the case study was carried out with real transportation project. As a result, the Environment-Benefits increased by 30%. If the methodology suggested in this study is applied to feasibility study it will help to activate the investment of the environment-friendly modes like railway in the future.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.9 no.1
• /
• pp.156-172
• /
• 1999

Potential chemical hazards encountered in painting operation of four shipyards and a ship-repair shop were investigated through the material safety data sheets (MSDS). Material safety data sheets (MSDS) for 307 paints, 50 thinners and 34 binders were collected and reviewed. It was shown that various organic solvents such as aromatic hydrocarbons, aliphatic hydrocarbons, ketones, alcohols, glycols, glycol ether acetates and esters were contained in painting materials. Of these solvents, xylene was found in the largest number of painting materials. sixty percent of the thinners contained xylene in the contents of 20-100%. Other most frequently found solvents were 1-methoxypropanol, 1-methoxypropyl acetate, n-butanol, methyl isobutyl ketone, toluene, isopropanol, and n-butyl acetate, etc. Glycol ethers such as 2-methoxyethanol (2-ME), 2-methoxyethyl acetate (2-MEA), 2-ethoxyethanol (2-EE), 2-ethoxyethyl acetate (2-EEA) and 2-butoxyethanol (2-BA) were regarded as having the potential to cause adverse reproductive effects, embryotoxic effect and hematotoxic effects, and were found in some epoxy panting materials. Coal tar pitch was included in some paints(13%) where polynuclear aromatic hydrocarbons (PAHs) could be contaminated. Inorganic pigments such as lead chromate and zinc potassium chromate were found in some paints (8%). The epoxy resin based paints, which may contain isocyanates such as toluene diisocyanates and hexamethylene diisocyanates causing potential sensitization and asthma to upper respiratory organ, were mostly used in the shipyards. The constituents in the MSDS were significantly different from the results analyzed using gas chromatography/mass detector: minor constituents or impurities were omitted in many MSDS. In conclusion, xylene was the most frequent organic solvent in painting materials, and glycol ethers, including 2-ME, 2-MEA, 2-EE, 2-EEA and 2-BA, were found some products. Also, painting workers may be exposed to PAHs, lead, chromate, isocyanates, organic tin and other various chemicals. The compositions of chemicals in painting materials were variable significantly, and the hazards were changed. These facts should be considered in environmental monitoring and control of the hazards.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.1
• /
• pp.29-39
• /
• 2018

In this study, the applicabilities of flood risk indices using FVI from IPCC, PSR method from OECD, and DPSIR method from EEA, were analyzed. Normalized values of daily maximum rainfall, hourly maximum rainfall, ten minute maximum rainfall, annual precipitation, total days of heavy rainfall (more than 80mm/day), density of population, density of asset, DEM, road statistics, river maintenance ratio, reservoir capacity, supply ratio of water supply and sewerage, and pumping capacity were constructed from 2000 to 2015 for nationwide 113 watersheds, to estimate flood risk indices. The estimated indices were compared to 4 different types of flood damage such as the number of casualties, damage area, the amount of flood damage, and flood frequency. The relationships between flood indices and different flood damage types demonstrated that the flood index using the PSR method shows better results for the amount of flood damage, the number of casualties and damage area, and the flood index using the DPSIR method shows better results for flood frequency.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.37-44
• /
• 2002

The polymer blends of waste polyvinyl chloride (RPVC) and waste polyethylene(RPE) were prepared by melt mixing, and their morphology and tensile properties were evaluated after the copolymers having an ethylene group in backbone and ester group in side position were added as comptatibilizers. The blend compositions were varied as follows ; RPVC/RPE 85/15 wt%, where RPVC formed a continuous phase : 50/50, mid composition : 15/85, RPE a continuous phase. The blends revealed a very low compatibility between component polymers because they showed domain sizes greater than $10\mu\textrm{m}$ over all compositions, especially the worst compatibility around mid composition. The blends showed higher compatibility when ethylene vinylacetate copolymer(EVA) and ethylene ethylacrylate-graft-methyl methacrylate copolymers(EEA-MMA) were added.

• Journal of Gastric Cancer
• /
• v.4 no.2
• /
• pp.121-125
• /
• 2004

Purpose: Esophagojejunal anastomotic complications after a total gastrectomy include leakage, stenosis, bleeding, and abscess formation. Especially, the mortality rate for esophagojejunal anastomotic leakage is $80\%$. Although these complications hare been reduced by the usage of the EEA stapler, they are still serious and depend on various factors: the surgeon's experience, the stage of disease, the extent of surgical intervention, the method of operation, and the patient. Some local factors, such as vascularization of the graft, traction on the anastomosis suture line, and local infections, have been implicated as contributing to these complications. Materials and Methods: During the period $1995\∼2003$, of the 850 gastrectomies for gastric carcinomas, 171 were intra-abdominal total gastrectomies. All of these 171 operations were performed by one surgeon using a routine D2 lymph-node dissection and a 25-mm EEA stapler on an antecolic end-to-side esophagojejunostomy. In the 77 cases a seromuscular reinforced suture at the esophagojejunostomy site was performed, and in 94 cases, a whole layer reinforced suture with absorbible materials was used. We evaluated the incidence of complications according to age, sex, stage of patients, and combined resection. Also, we compared the incidences of complications for seromuscular and whole layer reinforced sutures. Results: The complications are major leaks ($2.9\%$), minor leaks ($3.5\%$), stenosis, bleeding ($1.8\%$), and abscess formation formation ($1.8\%$). In the five cases of major leaks, there were four mortalities with operative methods. The other patients with stenosis, bleeding, and abscess formation were treated conservatively with success. The incidences of complications were not related with age, sex, stages, and combined resection. The incidences of complications for the whole layer reinforced suture group ($2.9\%$) were less than those for the seromuscular reinforced group ($8.8\%$, P=0.04). Conclusion: The most serious complication of esophagojejunal anastomosis is major leakage with an $80\%$ mortality. The other complications are stenosis, bleeding, and abscess formation, for which no mortalities occurred during this study. Whole layer suture of the esophagojejunal anastomotic site is an important method for preventing leakage.

• Proceedings of the KIEE Conference
• /
• 2008.09a
• /
• pp.203-206
• /
• 2008

To improve mean-life and reliability of power cable in this study, we have investigated chemical properties showing by changing the content of carbon black that is semiconductive additives for underground power transmission. Specimens were made of sheet form with the three of existing resins and the nine of specimens for measurement. Chemical properties of specimens was measured by FT-ATR (Fourier Transform Attenuated Total Reflectance). The condition of specimens was a solid sheet. We could observe functional group (C=O, carbonyl group) of specimens through FT-ATR. From these experimental result, the concentration of functional group (C=O) was high according to increasing the content of carbon black. We could know EEA was excellent more than other specimens from above experimental results.

• Journal of Multimedia Information System
• /
• v.2 no.3
• /
• pp.263-274
• /
• 2015

The subject of this work is the complex discrete systems simulation special features with the aid of dynamic graph models. The proposed simulation technique allows to determine the ways for tasks solutions in terms of discrete systems analysis and synthesis of various complication: one-dimensional and multidimensional, steady and unstable, with the pulse elements abnormal operating mode and others. Often complex control systems analysis and synthesis task solutions, via classical approach comes out to be insolvent, because of the computational problems. The application of graph models allows to perform clear and strict characterization and computer procedures automation. The optimal controls synthesis algorithm presented in this paper, transferring the discrete system from target initial state to target final state within the minimum time, allows to consider the zero initial conditions systems, with the initial potential energy, with the control actions limitations and complex pulse elements operating mode.

• Journal of Intelligence and Information Systems
• /
• v.2 no.1
• /
• pp.45-58
• /
• 1996

This paper describes an a, pp.oach to recognizing composite features of prismatic parts. AAG (Attribute Adjacency Graph) is adopted as the basis of describing basic feature, but it is extended to enhance the expressive power of AAG by adding face type, angles between faces and normal vectors. Our a, pp.oach is called Extended AAG (EAAG). To simplify the recognition procedure, feature classification tree is built using the graph types of EEA and the number of EAD's. Algorithms to find open faces and dimensions of features are exemplified and used in decomposing composite feature. The processing sequence of recognized features is automatically determined during the decomposition process of composite features.