• 한국기계가공학회지
• /
• 제16권3호
• /
• pp.38-44
• /
• 2017

The technology of electrical discharge tap machining may be appropriate for making thread out of highly brittle material. Especially, it is very difficult to machine tap with the traditional method if the brittle material has been hardened by quenching. In this study, the shape of electrical discharge blind hole tap machining was analyzed by discharge time, discharge current, and the flushing hole condition after quenched the tool steel of STD11 has discharged the tap shape with a screw-shaped copper(Cu) electrode. An experimental design was planned and analyzed by Taguchi robust experimental design. The result showed that the shape of the blind hole discharge tap was influenced by the flushing hole, discharge time, and discharge current. The most important factor of the processing conditions was found to be the discharge current. When blind hole EDM with a copper electrode with a flushing hole was conducted, the discharged shape was found to be smooth and the angle of the discharged tapped thread was also found to be close to the thread angle of $60^{\circ}$. As the values of discharge time and discharge current increased, the EDMed surface coarsened due to the increase of the single discharge energy and the shape of the thread collapsing.

• 한국기계가공학회지
• /
• 제15권5호
• /
• pp.131-136
• /
• 2016

Currently, an EDM tapping procedure has comprised some parts of the engraving discharge process for the press die. Usually, tapping has been used in cases where we are unable to mechanically machine using steelwork processes due to an increase in the hardness of a material after heat treatment in relation to a design change or missing process. Here, we analyze the influence of discharge tap shape on discharge time, discharge current, and the number of repetition conditions when a cold-work tool steel (STD11) has been treated with a discharge tapped by a screw-shaped cu electrode. The most important influence on processing condition has been determined to be the number of discharge repetitions. As this number increases, the angle reduction of a thread closes to an angle of the electrode via a power generation reduction. The optimal combination of conditions has been determined to be three discharge repetitions, $180{\mu}s$ of discharge time (same as existing regulations), and 25.4A of peak current. A 0.2749db advantage has emerged after comparing between this combination of optimal conditions and the SN rate of existing regulations.

• 한국안전학회지
• /
• 제19권2호
• /
• pp.21-25
• /
• 2004

This study deals with the characteristics of wire-cut EDM(Electrical Discharge Machining)process in aluminum alloys. Besides 2 series and 7 series of aluminum alloys for aerospace applications, porous aluminum is tested, which is used for sound absorbing matherial and interior and exterior material of building. Jinyoung JW-30 wire cutting machine was used in this experiment. Tap wate passed a filter and ionization was used as the discharging solution. An immerision method was applied as a cooling method because it separates chips effectively and machinability is good even with low value of electric current. The speed of fabrication was estimated by measuring the travel distance of the work piece and time spent for the movement. As pulse-on-time increased the fabrication speed decreased. On the other hand, as peak voltage of peak current increased the fabrication speed increased. In general 7075 aluminum alloy resulted in higher fabrication speed.

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1147-1154
• /
• 1990

본 연구에서는 초음파 화학 가공(ultrasonicassisted chemical mahining)을 이용하여 100$\mu\textrm{m}$이하의 전극봉을 제작하였고 제작한 전극을 이용하여 미세구멍을 방전 가공함으로써 가공특성을 파악하고, 방전액을 각각 등유(kerosene)와 물로하여 구멍의 표면을 비교, 분석하였으며 전극의 지름, 가공물의 두께에 대한 오버컷과 경사도(tap- er) 그리고 전극의 마멸을 조사하였다.