Browse > Article
http://dx.doi.org/10.14775/ksmpe.2016.15.5.131

A Study on the Electrical Discharge Machining Tap by using Cu Electrodes of the Cold-Work Tool Steel  

Lee, Eun-Ju (Changwon Campus of KOREA POLYTECHNIC.)
Park, In-Soo (Changwon Campus of KOREA POLYTECHNIC.)
Kim, Hu-Kwon (Ssangyong Motor Company Machining Team)
Wang, Duck-Hyun (School of Mechanical Engineering, Kyungnam University)
Chung, Han-Shik (Department of Energy and Mechanical Engineering, Institute of Marine Industry, Gyeongsang National University)
Lee, Kwang-Sung (Department of Energy and Mechanical Engineering, Institute of Marine Industry, Gyeongsang National University)
Publication Information
Journal of the Korean Society of Manufacturing Process Engineers / v.15, no.5, 2016 , pp. 131-136 More about this Journal
Abstract
Currently, an EDM tapping procedure has comprised some parts of the engraving discharge process for the press die. Usually, tapping has been used in cases where we are unable to mechanically machine using steelwork processes due to an increase in the hardness of a material after heat treatment in relation to a design change or missing process. Here, we analyze the influence of discharge tap shape on discharge time, discharge current, and the number of repetition conditions when a cold-work tool steel (STD11) has been treated with a discharge tapped by a screw-shaped cu electrode. The most important influence on processing condition has been determined to be the number of discharge repetitions. As this number increases, the angle reduction of a thread closes to an angle of the electrode via a power generation reduction. The optimal combination of conditions has been determined to be three discharge repetitions, $180{\mu}s$ of discharge time (same as existing regulations), and 25.4A of peak current. A 0.2749db advantage has emerged after comparing between this combination of optimal conditions and the SN rate of existing regulations.
Keywords
EDM; EDM Tap; Design of experiments;
Citations & Related Records
Times Cited By KSCI : 5  (Citation Analysis)
연도 인용수 순위
1 Kim, C. H., "Improvement of the ED-Drilling Machinability using Multi-hole Electrodes," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 11, No. 5, pp. 88-93, 2012.
2 Krishna, K., S., Anand, S., S., Sanjay, A., "Experimental investigation into the micro-EDM characteristics of conductive SiC," Journal of Ceramics International,Vol. 42 No. 1, pp. 1597-1610, 2016.   DOI
3 Kwon, W. T., Kim, Y. C., "Process Optimization for Productivity Improvement during EDM machining of a micro-hole," Journal of the Korean Society of Manufacturing Technology Engineers, Vol. 21 No.4. pp. 556-562, 2012.   DOI
4 Lee, C. S., "A Method of Hole Pass-Through Evaluation for EDM Drilling," Journal of the Korean Institute of Industrial Engineers, Vol. 38, No. 3, pp. 220-226, September 2012.   DOI
5 N. M. Kumar, S. S. Kumaran, L. A. Kumaraswamidhas, "An investigation of mechanical properties and material removal rate, tool wear rate in EDM machining process of AL2618 alloy reinforced with Si3N4, AlN and ZrB2 composites," Journal of Alloys and Compounds, Vol. 650, pp. 318-327, 2015.   DOI
6 J. C. Ferreira, "A study of die helical thread cavity surface finish made by Cu-W electrodes with planetary EDM," International Journal of Advanced Manufacturing Technology, Vol. 34, No. 11-12, pp. 1120-1132, 2007.   DOI
7 Song, K. Y., "DEVELOPMENT OF STRIP EDM," A Thesis for a Doctorate, Seoul National University, Republic of Korea, 2012
8 Kim, B., H., "Micro Hole Machining Using MEDM with Screw-Type Electrode," Master Thesis, Seoul University 1999.
9 Ryu, Ch. W., Choi, S. D., "Characteristics of Surface Roughness Based on Wire Vibration and Wire-cut Electric Discharge Machining of Aluminum Alloy 6061 (I)" Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 2, pp. 100-107, 2015.   DOI
10 Ryu, Ch. W., Choi, S. D., "Characteristics of Surface Roughness According to Wire VibrationWire-cut Electric Discharge Machining of Aluminum Alloy 6061(II)" Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 4, pp. 100-107, 2015.   DOI
11 H.C. Tsai, B.H. Yan, F.Y. Huang, "EDM performance of Cr/Cu-based composite electrodes," International Journal of Machine Tools and Manufacture, Vol. 43, No. 3, pp. 245-252, 2003.   DOI
12 D.D. DiBitonto, P.T. Eubank et al., "Theoretical models of the electrical discharge machining process. I. A. simple cathode erosion model," Journal of Applied Physics, Vol. 66, No. 9, pp. 4095-4103, 1989.   DOI