• Journal of the Korean Wood Science and Technology
• /
• v.27 no.2
• /
• pp.38-45
• /
• 1999

This study was to figure out proper Formaldehyde/Urea molar ratio of UF resin with satisfactory bonding strength of plywood and properties of particleboard. The six kinds of UF resins were manufactured with F/U molar ratio 1.0, 1.2, 1.4, 1.6, 1.8, and 2.0. The boards were made of three kinds of raw materials : Veneer, Sliver-Particle and Strand-Particle. Manufacturing condition of plywood : amount of mixing resin was 150g/$m^2$. The fourty secs/mm simple-pressing schedule in the pressure 10kgf/$m^2$ was applied for 480mm${\times}$700mm board at the temperature of $110^{\circ}C$ in a hot press. Manufacturing condition of particleboard : Target density was 0.65g/$cm^2$. The stepwise 9 minutes- multi-pressing schedule in the maximum pressure 40kgf/$cm^2$, the minimum pressure 15kgf/$cm^2$ was applied for $480mm{\times}634mm{\times}12mm$ board at the temperature of $150^{\circ}C$ in a hot press. The results are as follows : I. In bonding strength, plywood which was made by F/U molar ratio 1.2 showed the highest value. Other molar ratio resin also gave the satisfied value of KS standard, 7.5kgf/$cm^2$. 2. In internal bond strength of particleboard, Sliver-Particleboard(SLPB) and Strand-Particleboard(STPB) varied respectively from 5.9kgf/$cm^2$ to 4.8kgf/$cm^2$, from 6.7kgf/$cm^2$ to 5.4kgf/$cm^2$. SLPB with F/U=1.2 and STPB with F/U=1.6 had higher IB value. Also, both SLPB and STPB showed lower IB value in F/U molar ratio 2.0 and 1.0. 3. SLPB and STPB with six kinds of UF resin respectively satisfied bending strength of KS standard 150 Type(130kgf/$cm^2$) and 200 Type(180kgf/$cm^2$). Bending strength data for both of SLPB and STPB showed little or no loss from F/U=1.8 to F/U=1.2. Also, STPB was approximately two times higher than that of SLPB. Therefore, the raw material's shape had more effect on bending strength than the FlU molar ratio. 4. F/U=1.6 and 1.4 showed the lower thickness swelling in SLPB and STPB. All of STPBs satisfied thickness swelling of KS standard, under 12%.

• Korean Journal of Heritage: History & Science
• /
• v.52 no.2
• /
• pp.142-171
• /
• 2019

The dragon is an imaginary animal that appears in the legends and myths of the Orient and the West. While dragons have mostly been portrayed as aggressive and as bad omens in the West, in the Orient, as they symbolize the emperor or have an auspicious meaning, dragons signify a positive meaning. In addition, as the dragon symbolizes the emperor and its type has been diversified considering it as a divine object that controls water, people have tried to express it as a figure. The records related to dragons in the Goryeo dynasty appeared with diverse topics in 'History of Goryeo' and are generally contents related to founding myths, rituals for rain, and Shinii (神異), etc. The founding myth emphasizes the legality of the Goryeo dynasty through the dragon, and this influenced the formation of the dragon's descendants. In addition, the ability to control water, which is a characteristic of the dragon, was symbolized as an earth dragon related to the rainmaking ritual, i.e., wishing for rain during times of drought. Since the dragon was the symbol of the royal family, the use of the dragon by common people was strictly restricted. Furthermore, the association of a bronze dragon mirror with the royal family is hard to be excluded. The type and quantity of bronze double dragon mirrors discovered to have existed during the Goryeo dynasty is great, and the production and the distribution of bronze mirrors with double dragons seem to have been more active compared to other bronze mirrors, as bronze mirrors with double dragons produced during Goryeo and bronze mirrors originating in China were mixed. Therefore, in this article, the characteristics of diverse bronze mirrors from the 10th century to the 14th century in China were examined. It seems that the master craftsmen who produced bronze mirrors with double dragons during the Goryeo dynasty were influenced by Chinese composition patterns when making the mirrors. Because there were many cases where a bronze mirror's country of origin could not easily be determined, in order to identify the differences between bronze double dragon mirrors produced during the Goryeo dynasty and bronze mirrors produced in China, meticulous analysis was required. Thus, to ascertain that Goryeo mirrors were not imitations of bronze mirrors with double dragons originating in China but produced independently, the mirrors were examined using the bronze double dragon mirror type classification system existing in our country. Bronze mirrors with double dragons are classified into three types: Type I, which has the style of the Yao dynasty, includes the greatest proportion; however, despite there being only a small quantity for comparison, Types II and III were selected for the analysis of the bronze mirrors with double dragons made in Goryeo because they have unique composition patterns. As mentioned above, distinguishing bronze mirrors made during Goryeo from bronze mirrors made in China is challenging because Goryeo bronze mirrors were made under the influence of China. Among them, since the manufacturing place of the bronze mirrors with double dragons found at the nine-story stone pagoda in Woljeongsa Temple in Pyeongchang is questionable and the composition pattern of the bronze mirror is hard to find on bronze mirrors with double dragons made in China, the manufacturing place of those bronze mirrors were examined. These bronze mirrors with double dragons were considered as bronze mirrors with double dragons made during the Goryeo dynasty adopting the Yao dynasty style composition pattern as aspects of the composition pattern belonged to Type I, and the detailed combination of patterns is hard to find in mirrors produced in China.

• Journal of Intelligence and Information Systems
• /
• v.26 no.2
• /
• pp.1-25
• /
• 2020

In this paper, we suggest an application system architecture which provides accurate, fast and efficient automatic gasometer reading function. The system captures gasometer image using mobile device camera, transmits the image to a cloud server on top of private LTE network, and analyzes the image to extract character information of device ID and gas usage amount by selective optical character recognition based on deep learning technology. In general, there are many types of character in an image and optical character recognition technology extracts all character information in an image. But some applications need to ignore non-of-interest types of character and only have to focus on some specific types of characters. For an example of the application, automatic gasometer reading system only need to extract device ID and gas usage amount character information from gasometer images to send bill to users. Non-of-interest character strings, such as device type, manufacturer, manufacturing date, specification and etc., are not valuable information to the application. Thus, the application have to analyze point of interest region and specific types of characters to extract valuable information only. We adopted CNN (Convolutional Neural Network) based object detection and CRNN (Convolutional Recurrent Neural Network) technology for selective optical character recognition which only analyze point of interest region for selective character information extraction. We build up 3 neural networks for the application system. The first is a convolutional neural network which detects point of interest region of gas usage amount and device ID information character strings, the second is another convolutional neural network which transforms spatial information of point of interest region to spatial sequential feature vectors, and the third is bi-directional long short term memory network which converts spatial sequential information to character strings using time-series analysis mapping from feature vectors to character strings. In this research, point of interest character strings are device ID and gas usage amount. Device ID consists of 12 arabic character strings and gas usage amount consists of 4 ~ 5 arabic character strings. All system components are implemented in Amazon Web Service Cloud with Intel Zeon E5-2686 v4 CPU and NVidia TESLA V100 GPU. The system architecture adopts master-lave processing structure for efficient and fast parallel processing coping with about 700,000 requests per day. Mobile device captures gasometer image and transmits to master process in AWS cloud. Master process runs on Intel Zeon CPU and pushes reading request from mobile device to an input queue with FIFO (First In First Out) structure. Slave process consists of 3 types of deep neural networks which conduct character recognition process and runs on NVidia GPU module. Slave process is always polling the input queue to get recognition request. If there are some requests from master process in the input queue, slave process converts the image in the input queue to device ID character string, gas usage amount character string and position information of the strings, returns the information to output queue, and switch to idle mode to poll the input queue. Master process gets final information form the output queue and delivers the information to the mobile device. We used total 27,120 gasometer images for training, validation and testing of 3 types of deep neural network. 22,985 images were used for training and validation, 4,135 images were used for testing. We randomly splitted 22,985 images with 8:2 ratio for training and validation respectively for each training epoch. 4,135 test image were categorized into 5 types (Normal, noise, reflex, scale and slant). Normal data is clean image data, noise means image with noise signal, relfex means image with light reflection in gasometer region, scale means images with small object size due to long-distance capturing and slant means images which is not horizontally flat. Final character string recognition accuracies for device ID and gas usage amount of normal data are 0.960 and 0.864 respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.8
• /
• pp.574-582
• /
• 2012

This study presents the concentrations of the polycyclic aromatic hydrocarbons (PAHs) listed as priority pollutants by United States Environmental Protection Agency (US EPA), in 98 sludges from 54 industrial wastewater treatment facilities of South Korea. The mean concentrations of ${\Sigma}_{16}PAHs$ were ranged from 32.5 ${\mu}g/kg-dw$ to 1189.3 ${\mu}g/kg-dw$ by industries, and the highest content was found in the petrochemical industry, followed by chemical, clothing manufacturing and dying, pulp and papermaking, secondary wastewater treatment, and food/beverage producing industries. Comparisons to the EU and Danish standards of ${\Sigma}_{16}PAHs$ in sewage sludge for land application showed only two samples (one from petrochemical, and the other from chemical industry) exceeded the limits. ANOVA test with PAH concentrations as variables revealed no statistically significant influences by industrial types and sampling time (i.e., seasonal variations). Pearson correlations between individual PAHs showed strong relationships (r>0.7) among 4-ring PAHs. Concentrations of acenaphthylene, anthracene, fluoranthene, benzo(a)anthracene, benzo(f)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene presented strong correlations to ${\Sigma}_{16}PAHs$. Principal component analysis discriminated entire samples into three groups by two principal components (PC1 and PC2) with 70% of data variations, in which industrial types were not of importance, but a dominance of certain PAHs. Samples in group-I, which is high PC1 and low PC2, were characterized by a dominance of 2-ring PAHs, and in group-II, PC1 and PC2 showed a linear relation, was dominant 4-ring PAHs. Group-III with low PC1 and high PC2 includes 17 samples showing a noticeably high contribution of 3-ring PAHs to ${\Sigma}_{16}PAHs$. This study provides concentrations of PAHs in industrial sludges collected from a wide variety of sources (six industrial types) and two seasons of sampling events, and the comparison of ${\Sigma}_{16}PAHs$ with other studies are also discussed.

• Korean Journal of Agricultural Science
• /
• v.39 no.3
• /
• pp.335-340
• /
• 2012

During the manufacturing process of chestnut, 50% of biomass is produced as chestnut shell (CS) or chestnut hull (CH), a forestry by-product. Due to its high fiber content and economic benefit, there is a possibility of using chestnut hull as a supplement for a ruminant diet. Few studies, however, have been conducted on evaluating nutritive value of chestnut hull for ruminant animals. The objective of this study were thus to analyze chemical composition of CS, a by-product after the first processing of chestnut, and CH, a by-product after the second processing, and access in vitro rumen fermentation characteristics of them. For the in vitro fermentation using strained rumen fluid obtained from a fistulated Hanwoo steer, commercial total mixed ration (TMR) for dairy goat was used as a basal diet and was replaced with different proportions of chestnut shell and hull. A total number of 13 treatments were carried out in this study: 100% TMR, 100% CS, 100% CH, a mix with 50% CS and 50% of CH (MIX), TMR replaced with 5%, 10%, or 15% of CS, CH, or MIX, respectively. For each treatment, in vitro dry matter digestibility (IVDMD) and pH after 48 hours of rumen fermentation were measured. Gas production at 6, 12, 24, 48 hours of incubation was also analyzed. Compared to CH, CS contains higher level of fiber (NDF, ADF, lignin) and consequently has a lower amount of non-fiber carbohydrate, but no difference was observed in the other nutrients (i.e. crude protein, crude fat, and ash). IVDMD was significantly (p<0.05) the highest in 100% CH (71.97%) and the lowest in 100% CS (42.80%). Addition of CH by replacing TMR did not affect IVDMD, while an increase in the proportion of CS tended to decrease IVDMD. The total gas production after 48 hours of incubation and the rate of gas production were also the highest in 100% CH and the lowest in 100% CS (P<0.05). Likewise, the pH after 48 hours of fermentation was significantly (p<0.05) the lowest in 100% CH (6.33) and the highest in 100% CS (6.50), and no significant difference in gas production was observed when TMR was replaced with CS or CH up to 15% (P>0.05). In conclusion, CH may successfully be used for a supplement in a ruminant diet. The nutritive value of CS is relative low, but can replace, if not 100%, low quality forage. This study provides valuable information about the nutritive value of CS and CH. An in vivo trials, however, is needed for conclusively accessing the nutritive value of CS and CH.

• Korean Chemical Engineering Research
• /
• v.56 no.4
• /
• pp.577-584
• /
• 2018

This study was conducted to investigate the potential of chicken feather (CF), which is a by-product in poultry industry, as a partial substitute of wood fiber in the production of wood-based fiberboard. Keratin-type protein constituted the majority of CF, and its appearance did not differ from that of wood fiber. When the formaldehyde (HCHO) adsorptivities of CF compared by its pretreatment type, feather meal (FM), which was pretreated CF with high temperature and pressure and then grounded, showed the highest HCHO adsorptivity. In addition, there was no difference between the adsorbed HCHO amounts, which was measured by dinitrophenylhydrazine method, of scissors-chopped CF and CF beated with an electrical blender. Mechanical properties and HCHO emission of medium-density fiberboards (MDF), which were fabricated with wood fiber and 5 wt% CF, beated CF or FM based on the oven-dried weight of wood fiber, were not influenced by the pretreatment type of CF. However, when the values compared with those of MDF made with just wood fiber, thickness swelling and HCHO emission of the MDF were improved greatly with the addition of CF, beated CF or FM. Based on the results, it might be possible to produce MDF with improved dimensional stability and low HCHO emission if CF, beated CF or FM is added partially as a substitute of wood fiber in the manufacturing process of MDF produced with the conventional urea-formaldehyde resin of $E_1$ grade. However, the use of CF or FM in the production of MDF has a low economic feasibility at the current situation due to the securing difficulty and high cost of CF. In order to enhance the economic feasibility, it requires to use CF produced at small to medium-sized chicken meat plants. More importantly, it is considered that the technology developed from this research has a great potential to make provision for the prohibition of animal-based feed and to dispose environmentally avian influenza-infected poultry.

• Journal of Life Science
• /
• v.19 no.2
• /
• pp.277-283
• /
• 2009

Biogenic amines are generally formed through the decarboxylation of specific free amino acids by exogenous decarboxylases released by microbial species associated with the fish products and fermented feeds. This study was conducted to investigate the properties of e tuna waste regarding the control of degradation of biogenic amines (histamine, tyramine, tryptamine, putrescine, and cadaverine) that might be related with the anti-nutritional factor of the tuna waste that is used for manufacturing domestic fish meal. The values of pH and the salt content were 6.51, 3.35% in tuna waste and 5.58 and 5.83% in tuna fish meal, respectively. The strains and dominant bacteria tested in the tuna waste sample were 9.20, 9.29, 5.67, 7.82 and 7.58 log CFU/g of total bacteria, aerobic plate count (APC), total coliform (TC), Lactobacillus spp. and Bacillus spp., respectively. The main histamine forming-bacteria (HFB) in tuna waste were detected by silica gel thin-layer chromatography (TLC) and 7 histamine-forming bacterial species were isolated among microbes grown in selective medium. The histamine concentration was determined by detection of fluorescence of ο-phthaldialdehyde (OPA) derivatives using HPLC and the date were used to reconfirm the identities of the amine-producing bacteria. The 15 histamine- forming bacteria strains grown in trypicase soy broth (TSB) supplemented with 1% L-histidine (TSBH) were identified as Lactococcus(L.) lactis subsp. lactis, Klebsiella pneummonlae, L. garvieae 36, Vibrio olivaceus, Hafnia alvei and L. garvieae which were main dominant amine - producing strains, and Morganella morganii identified by 16S ribosomal RNA (rRNA) sequencing with PCR amplification. A Phylogenetic tree generated from the 16S rRNA sequencing data showed different phyletic lines that could be readily classified as biogenic amine forming gram-positive and negative bacteria.

• Applied Biological Chemistry
• /
• v.29 no.2
• /
• pp.107-115
• /
• 1986

The chemical changes and the quality of the soysauce which was Bade by new convenient method using vinyl teat instead of koji room, replacing wheat with milled barley koji were investigated. Protease activity of the koji was higher as tile ratio of soybeans was increased but amylase activity was higher as the ratio of milled barley was increased. The amounts of total nitrogen showed substantial increases until 80 days and afterwards, their rates of increases were lower. The more its content of soybeans, the higher its amount of total nitrogen, The amount of amino nitrogen increased slowly in all samples and the sample which had a large amount of soybeans was higher than those with small amounts of soybeans. The amount of ammonia nitrogen showed increases until 120 days tut decreased after then. The amount of reducing sugar showed increases until 80 days and decreased after then and the greater its source of carton, the higher its amount of reducing sugar. The total acid contort had large increases until 100 days in all samples and afterward they did not show any particular changes. The changes of pH decreased for 100 days and afterwards, they increased a little. In the original soysauce, combined ratio of soybean 3 to milled barley 2 and the sample of those ratio 4 : 1 are better than others and in diluted soysauce combined ratio of soybean 4 to milled barley 1 is better than the others. In original soysauce the use of $20{\sim}40%$ barley koji, which is added to soybeans, is superior and diluted soysauce the use of 20% barley koji is superior.

• Journal of Distribution Science
• /
• v.9 no.2
• /
• pp.31-36
• /
• 2011

I conducted empirical analyses of what happens when an offline channel expands to an online channel and whether the pre-existing offline channel's competitive assets (e.g. brand reputation and level of service satisfaction) can be linked to online channel preference. I found that an offline channel's brand reputation and level of service satisfaction can have a direct influence on offline channel preference and a second-hand influence on online channel preference. Thus, if the competitiveness of the online channel is strong enough and its customers have a higher preference for the offline channel, they will be committed and loyal to the company. The resultant enhanced competitiveness of the offline channel will present opportunities for both present and future success. The main results are the following. First, the management of the distribution channel service quality is more important than that of the brand reputation. Customers' experiences of service and subjective evaluations are not important only as the leading factors in the long-term brand reputation management but also as influential factors in channel preference. SoThus, given that the service quality of the pre-existing channel is not the customers' main concern, a strategy of improving the level of service satisfaction aimed at present customers is more valuable than a wide brand positioning strategy aimed at general and new customers. Second, when an offline channel company establishes an internet shopping mall on an online channel, it is highly likely that the preference and subjective evaluation of the present customers will influence the online channel. This applies not only to the special case of an expansion from an offline intermediary channel to an online one, but also to an online channel acting as an expansion of the business model of a conventional manufacturing or service company: both cases are vertical integrations of marketing channels in an expansion of the distribution channel. My theory applies to a wide range of contexts. Third and finally, any business strategy can grasp the meaning of 'channel expansion. Fundamentally, it is an expansion of the sales activity channel and marketing activity. However, it is also a way of enhancing marketing and sales competitiveness through an expansion to an online or offline channel. The expansion of an offline company to an online channel could be seen not as improvement but as an innovation of the business process by which two goals are achieved with one technique. The former is expected to increase the sales of the offline company, and the latter is also expected to increase sales while also contributing to cost reduction.

• Korea journal of population studies
• /
• v.19 no.1
• /
• pp.93-122
• /
• 1996

This is a study of the determinants of sexual, contraceptive, and abortion behavior among unmarried female adolescents and young adults, which has emerged as a growing and serious health problem in Korea. As part of a larger project, data were gathered in three export zones: Kuro (Seoul), Kumi (Kyngbuk) Masan Changwon (Kyongnam) ; and the study samples are regrouped into three categories: 1) factory workers, i.e. , the reference group serving as program participants, 2) entertainment workers, and 3) ob-gyn patients. This study indicates that entertainment workers are at highest risk of experiencing premarital sex, STDs, contraceptive failure, unwanted pregnancies, and induced abortion. Of them, 20 percent had STDs as a result of first sexual experience: and about seven tenths had two or more pregnancies due to the adoption of low-efficacy methods. The proportion of those who had ever been pregnant was 60 percent for the group as a whole: 36 percent for the program participants: 64 percent for the entertainment workers ; and 91 percent four the ob-gyn patients. These proportions are exactly the same for abortion in each group, which means that all pregnancies ended in induced abortion. Of the respondents who said that they were sexually active at the time of survey, abortions were very high: 1.6 for the program participants, 2.3 for the entertainment workers, and 1.9 for the ob-gyn patients. About 80 percent of the women had abortions during the first trimester, and two thirds of the first abortions took place between the ages of 20 and 23. About one fourth experienced post-abortion complication, which was highest among the program participants (39 percent). Sixty percent of those with complications visited a hospital or took medicine to treat the problem. Even after the experience of induced abortion, the use of contraception was very low, except among the entertainment workers, whose level of use reached 53 percent. The most obvious recommendation, arising from this research, is that 'good-quality' counselling and family planning services be established under the auspices of both national and local government, particularly targeted for the entertainment workers as well as the factory workers in various textile, electronic, manufacturing, and other industrial sectors. We believe that entertainment sectors should be restructured radically so that young women who work for amusement bars and other entertainment sectors obtain protection from the risk of having unwanted pregnancies, STDs, and induced abortion.