• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.829-835
• /
• 2006

Rotatory two-phase transverse flux machine(TFM) is a relatively new type of motor with high power density, high torque, and low speed in comparison to conventional electrical motors. However, it has some shortcomings,.i.e. complex construction and high possibility of the magnetically induced vibration due to its inherent structure. This paper investigates the characteristics of the magnetic force and the torque in the rotatory two-phase TFM by using the 3-D finite element method and the spectral analysis. This research shows that the average torque decreases and that the torque ripple increases as the phase delay increases. It also shows that the unbalanced magnetic force is one of the dominant excitation forces in this machine. And it proposes a new topology of rotatory two-phase TFM to eliminate the unbalanced magnetic force.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.753-758
• /
• 2011

Magnetic field and Electric field of High Temperature Superconducting magnet are very important to analysis of superconducting magnet. The maximum perpendicular magnetic field was applied to the outermost pancake windings. The critical current of all the magnet windings is limited by the critical current of the outermost pancake windings. The E-J relation was used to determine the critical current, and an evolution s trategy was adopted for the optimization of gap length between each pancake windins. The results of calculations show that the critical current and the central magnetic field and uniformity increased by 82.6% and 31.6% and 50.8%, respectively, for a magnet consisting of ten pancake windings. This paper did an analysis the cause of increase the critical current and central magnetic field and uniformity in no gap and optimal gap model.

• Electrical & Electronic Materials
• /
• v.10 no.2
• /
• pp.113-118
• /
• 1997

For the amorphous F $e_{78}$ $B_{13}$S $i_{9-x}$G $e_{x}$ alloy, thermal analysis and measurements of the magnetic properties were carried out. As the content of Ge increased, the crystallization temperature was decreased and the Curie temperature was increased, and the tendencies were almost linear. The core loss of the amorphous alloy for x=1.7, field annealed at optimized condition, was 0.057 W/kg(l.0T, 60Hz), which was about 30% lower than that of no Ge added amorphous alloy (basic composition). Such a low core loss characteristics was thought to be caused by the lower coercive force and good squareness of B-H loop of the alloy.y.y.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.927-929
• /
• 2014

MRE(Magneto-rheological Elastomer) is a material which shows reversible and various modulus in magnetic field. Comparing to conventional rubber vibration isolator, MREs are able to absorb broader frequency range of vibration. These characteristic phenomena result from the orientation of magnetic particle (i.e., chain-like formation). Magnetic reactive powder(MRP), having rapid magnetic reaction, was selected as a magnetic particle to give magnetic field reactive modulus. The mechanical properties of manufactured MREs were measured with the application of magnetic field. The analysis of MR effect was carried out by FFT analyzer with various induced current. As induced magnetic field intensity increased and coated with MRP, increment of MR effect was observed.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.230.2-230.2
• /
• 2015

Nanoparticles of magnesium ferrite are used as a heterogeneous catalyst, humidity sensor, oxygen sensor and cure of local hyperthermia. These applications usually utilize the magnetic behavior of these nanoparticles. Moreover, magnetic properties of nanoferrites exhibit rather complex behavior compared to bulk ferrite. The magnetic properties of ferrites are complicated by spins at vortices, surface spins. Reports till date indicate strong dependency on the structural parameters, oxidation state of metal ions and their presence in octahedral and tetrahedral environment. Thus we have carried out investigation on magnesium ferrite nanoparticles in order to study coordination, oxidation state and structural distortion. For present work, magnesium ferrite nanoparticles were synthesized using nitrates of metal ions and citric acid. Fe L-edge spectra measured for these nanoparticles shows attributes of $Fe^{3+}$ in high spin state. Moreover O K-edge spectra for these nanoparticles exhibit spectral features that arises due to unoccupied states of O 2p character hybridized with metal ions. Mg K-edge spectra shows spectral features at 1304, 1307, 1311 and 1324 eV for nanoparticles obtained after annealing at 400, 500, 600, 800, 1000, and $1200^{\circ}C$. Apart from this, spectra for precursor and nanoparticles obtained at $300^{\circ}C$ exhibit a broad peak centered around 1305 eV. A shoulde rlike structure is present at 1301 eV in spectra for precursor. This feature does not appear after annealing. After annealing a small kink appear at ~1297 eV in Mg K-edge spectra for all nanoparticles. This indicates changes in local electronic structure during annealing of precursor. Observed behavior of change in local electronic structure will be discussed on the basis of existing theories.

• Journal of Magnetics
• /
• v.15 no.2
• /
• pp.91-98
• /
• 2010

The paper presents results of a study on the selective separation technology of ferrous and non-ferrous metals from broken light bulbs. The proposed method is to use magnetic fluids to obtain a magnetic fluid based- separation. [1] The study was conducted using three types of waste materials: regular light bulbs, auto light bulbs and neon tubes. In order to process the waste materials, a six stages technologic flow was developed: a) separation of light bulbs components; b) Physical and chemical analysis of raw materials; c) grain conditioning of the raw material; d) dry magnetic separation of ferrous components; e) magnetic fluid separation of non-magnetic material; f) recovery of the magnetic fluid adhered to the surface of the separated material grains. [2] This study shows that magnetic fluid separation is only profitable for regular and auto light bulbs and is not profitable in the case of neon tubes.

• Journal of The Korean Astronomical Society
• /
• v.48 no.3
• /
• pp.187-190
• /
• 2015

Data analysis and theoretical arguments support magnetic reconnection in a chromospheric current sheet as the mechanism of the observed photospheric magnetic flux cancellation on the Sun. Flux pile-up reconnection in a Sweet–Parker current sheet can explain the observed properties of canceling magnetic features, including the speeds of canceling magnetic fragments, the magnetic fluxes in the fragments, and the flux cancellation rates, inferred from the data. It is discussed how more realistic chromospheric reconnection models can be developed by relaxing the assumptions of a negligible current sheet curvature and a constant height of the reconnection site above the photosphere.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.163-164
• /
• 2010

• Progress in Superconductivity and Cryogenics
• /
• v.23 no.4
• /
• pp.61-69
• /
• 2021

This paper presents the analysis and experiment results on the electrical and thermal characteristics of metal insulation (MI) REBCO racetrack coil, which was wound with stainless steel (SS) tape between turn-to-turn layers, under rotating magnetic field and conduction cooling system. Although the field windings of superconducting rotating machine are designed to operate on a direct current, they may be subjected to external magnetic field due to the unsynchronized armature windings during electrical or mechanical load fluctuations. The field windings show the voltage and magnetic field fluctuations and the critical current reduction when they are exposed to an external magnetic field. Moreover, the cryogenic cooling conditions are also identified as the factors that affect the electrical and thermal characteristics of the HTS coil because the characteristic resistance changes according to the cryogenic cooling conditions. Therefore, it is necessary to investigate the effect of external magnetic field on the electrical and thermal characteristics of MI-SS racetrack coil for further development reliable HTS field windings of superconducting rotating machine. First, the major components of the experiment test (i.e., HTS racetrack coil construction, armature winding of 75 kW class induction motor, and conduction cooling system) were fabricated and assembled. Then, the MI racetrack coil was performed under liquid nitrogen bath and conduction cooling conditions to estimate the key parameters (i.e., critical current, time constant, and characteristic resistance) for the test coil in the steady state operation. Further, the test coil was charged to the target value under conduction cooling of 35 K then exposed to the rotating magnetic field, which was generated by three phrase armature windings of 75 kW class induction motor, to investigate the electrical and thermal characteristics during the transient state.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.6
• /
• pp.74-80
• /
• 2008

Analysis of the electromagnetic environment on topside of a ship is needed for optimal arrangement of all kinds of antennas to be installed on the shipboard in order to minimize the probability of EMI of equipment and subsystems in real ship after construction phase. In this paper we analyze the characteristics of electric-fields such as radiation patterns and near E-fields of V/UHF antennas installed on a shipboard. We compare simulated results with measurements on the real ship for near E-fields to verify the reliability of the computed electromagnetic environment. Although there are various factors causing errors such as cable loss and impedance mismatching etc. when measuring near E-field, both data show similar trends in the range of the acceptable tolerance.