• Journal of the Optical Society of Korea
• /
• v.15 no.2
• /
• pp.196-201
• /
• 2011

Near-field properties of light emanated from a subwavelength double slit of finite length in a thin metal film, which is essential for understanding fundamental physical mechanisms for near-field optical beam manipulations and various potential nanophotonic device applications, is investigated by using a three-dimensional finite-difference time-domain method. Near-field intensity distribution along the propagation direction of light after passing through the slit has been obtained from the phase relation of transverse electric and magnetic fields and the wave impedance. It is found that the near field of emerged light from the both slits is evanescent, that is consistent with conventional surface plasmon localization near the metal surface. Due to the finite of the slit, the amplitude of this evanescent field does not monotonically approach to than of the infinite slit as the slit length increases, i.e. the near-field of the longer slit along the center line can be weaker than that of the shorter one.

• Coupled systems mechanics
• /
• v.12 no.2
• /
• pp.167-181
• /
• 2023

The determination of the blast protection level and the corresponding minimum load-bearing capacity for a laminated glass (LG) window is of crucial importance for safety and security design purposes. In this paper, the focus is given to the window response under near-field blast loading, i.e., where relatively small explosives would be activated close to the target, representative of attack scenarios using small commercial drones. In general, the assessment of the load-bearing capacity of a window is based on complex and expensive experiments, which can be conducted for a small number of configurations. On the other hand, nowadays, validated numerical simulations tools based on the Finite Element Method (FEM) are available to partially substitute the physical tests for the assessment of the performance of various LG systems, especially for the far-field blast loading. However, very little literature is available on the LG window performance under near-field blast loads, which differs from far-field situations in two points: i) the duration of the load is very short, since the blast wavelength tends to increase with the distance and ii) the load distribution is not uniform over the window surface, as opposed to the almost plane wave configuration for far-field configurations. Therefore, the current study focuses on the performance assessment and structural behaviour of LG windows under near-field blasts. Typical behavioural trends are investigated, by taking into account possible relevant damage mechanisms in the LG window components, while size effects for target LG windows are also addressed under a multitude of blast loading configurations.

• Journal of Distribution Science
• /
• v.19 no.12
• /
• pp.1-14
• /
• 2021

Purpose: For the last few decades, TQM has become a hot topic in the inner-disciplinary field in the production management line. Still, unfortunately, the study of TQM and Quality Output management is partially only attached to the tangible side in the production management line. Whereas theoretically, the implications of TQM require incremental improvement in all management lines (e.g., HRM, Marketing, Operations, and Distribution Management). Therefore, starting from the main problem, this study aims to analyze the effect of total quality management, Organizational Culture, Perceived Distribution of Quality Awareness, and quality output through a more in-depth analysis. Research design, data and methodology: We conducted a survey of 170 respondents from managers, staff, and employees from 48 companies in Indonesia. We used a quantitative approach with the SEM method to answer this study's problem formulation and hypotheses. Results: The results of our research stated that based on the demonstration of statistical test results, all hypotheses were positive and significant, both direct and indirect relationship demonstrations. Conclusions: Universally, the findings in this study illustrate that the supporting factor for creating value-added in TQM and Quality output lies in the optimal and positive organizational culture and Perceived Distribution Quality Awareness factors in the organization.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.87-100
• /
• 1997

The ability of turbulence model to accurately describe the complex characteristics of the flow field and the fuel spray is of great importance in the optimum design of diesel engine. The numerical simulations of the flow field and the spray characteristics within the combustion chamber of direct injection model entgine are performed to examine the applicability of turbulence model. The turbulence models used are the RNG $\varepsilon$ model and the modified $\varepsilon$ model which included the compressibility effect due to the compression/expansion of the charges. In this study, the predicted results in the quiescent condition of direct injection model engine show reasonable trends comparing with the experimental data of spray characteristics, i. e., spray tip penetration, spray tip velocity. The results of eddy viscosity obtained using the $\varepsilon$ model in the spray region is significantly larger than that obtained using the RNG $\varepsilon$ model. The application of the RNG model seems to have some potential for the simulations of the spray characteristics, e. g., spray tip penetration, spray tip velocity, droplets distribution over the $\varepsilon$ model.

• Journal of Mechanical Science and Technology
• /
• v.20 no.2
• /
• pp.262-270
• /
• 2006

Direct numerical simulations (DNS) of turbulent channel flows up to $Re_{\tau}=1270$ are performed to investigate an elliptic feature and strain rate field on cross sections of coherent fine scale eddies (CFSEs) in wall turbulence. From DNS results, the CFSEs are educed and the strain rate field around the eddy is analyzed statistically. The principal strain rates (i.e. eigenvalues of the strain rate tensor) at the CFSE centers are scaled by the Kolmogorov length $\eta$ and velocity $U_k$. The most expected maximum (stretching) and minimum (compressing) eigenvalues at the CFSE centers are independent of the Reynolds number in each $y^+$ region (i. e. near-wall, logarithmic and wake regions). The elliptic feature of the CFSE is observed in the distribution of phase-averaged azimuthal velocity on a plane perpendicular to the rotating axis of the CFSE $(\omega_c)$. Except near the wall, phase-averaged maximum $(\gamma^{\ast}/\gamma_c^{\ast})$ and minimum $(\alpha^{\ast}/\alpha_c^{\ast})$ an eigenvalues show maxima on the major axis around the CFSE and minima on the minor axis near the CFSE center. This results in high energy dissipation rate around the CFSE.

• Proceedings of the Acoustical Society of Korea Conference
• /
• 1994.06a
• /
• pp.785-790
• /
• 1994

The active noise control which regards the acoustic power as a target function to be minimized, is analyzed to test its feasibility of which simplifies the measurement system compared with the global acoustic energy based active noise control system. In fact, it is found that the acoustic power based active noise control strategy is equally likely as good as the global acoustic energy based active noise control method if the acoustic field of interest is diffusive or very low model density one. In the intermediate model density field, we also demonstrate that the power based control gives the similar results as the energy based control in terms of global sound energy reduction for the lightly damped enclosure which might be most important system in practical application. From all the theoretical and power based control strategy is dependent on the characteristics of the acoustic field to be controlled; i.e., the model density distribution, the degree of reverberation, and on the strength of modal interaction of the control source with the primary source; i.e., the location of control source.

• Wind and Structures
• /
• v.29 no.2
• /
• pp.111-127
• /
• 2019

The tapered and set-back type of unconventional designs have been used earlier in many buildings. These shapes are aerodynamically efficient and offer a significant amount of damping against wind-induced forces and excitations. Various studies have been conducted on these shapes earlier. The present study adopts a hybrid approach of turbulence modelling i.e., Detached-eddy Simulation (DES) to investigate the effect of height modified tapered and set-back buildings on aerodynamic forces and their sensitivity towards pressure. The modifications in the flow field around the building models are also investigated and discussed. Three tapering ratios (T.R.=(Bottom width- Top width)/Height) i.e., 5%, 10%, 15% are considered for tapered and set-back buildings. The results show that, mean and RMS along-wind and across-wind forces are reduced significantly for the aerodynamically modified buildings. The extent of reduction in the forces increases as the taper ratio is increased, however, the set-back modifications are more worthwhile than tapered showing greater reduction in the forces. The pressure distribution on the surfaces of the buildings are analyzed and in the last section, the influence of the flow field on the forces is discussed.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.2
• /
• pp.251-257
• /
• 2012

Human body communication means transmitting and receiving data through human body medium or through free space along with the human body skin. Electric field distribution around the human body between the transmitter and the receiver were calculated at five different frequencies with 5 MHz interval between 10 MHz and 30 MHz. Commercial electromagnetic simulation tool was used for the calculation of E-field distributions applying the Korean standard male model including 29 different kinds of human tissues. After calculating specific absorption rate(SAR) values on back of the hand, it was compared with International Commission on Non-Ionizing Radiation Protection(ICNIRP) human protection guideline. While conductivities(${\sigma}$) and relative permittivities(${\varepsilon}_r$) of the human tissues for each frequency were input as the analyzing parameters, electric field intensities near both hands were integrated along the integral line between the nearby electrodes for the calculation of the transmitting and receiving voltages whose ratio was defined as channel loss. The calculated channel losses were about ($75{\pm}1$) dB and showed nearly flat response all through the evaluated frequencies.

• Smart Structures and Systems
• /
• v.32 no.2
• /
• pp.83-99
• /
• 2023

The temperature prediction approaches of three important locations in an operational longitudinal slab track-bridge structure by using three typical neural network methods based on the field measuring platform of four meteorological factors and internal temperature. The measurement experiment of four meteorological factors (e.g., ambient temperature, solar radiation, wind speed, and humidity) temperature in the three locations of the longitudinal slab and base plate of three important locations (e.g., mid-span, beam end, and Wide-Narrow Joint) were conducted, and then their characteristics were analyzed, respectively. Furthermore, temperature prediction effects of three locations under five various meteorological conditions are tested by using three neural network methods, respectively, including the Artificial Neural Network (ANN), the Long Short-Term Memory (LSTM), and the Convolutional Neural Network (CNN). More importantly, the predicted effects of solar radiation in four meteorological factors could be identified with three indicators (e.g., Root Means Square Error, Mean Absolute Error, Correlation Coefficient of R2). In addition, the LSTM method shows the best performance, while the CNN method has the best prediction effect by only considering a single meteorological factor.

• Journal of Plant Biology
• /
• v.27 no.1
• /
• pp.25-32
• /
• 1984

A study on the dominance-diversity of forest vegetation in Mt. Seolag was conducted from May 1981 to Aug. 1983. Based on the field data, the dominance-diversity curves were for 16 sites including slopes and vallies. The curves are grouped in two types, lognormal distribution at the sites of mature vegetation and geometric series at the disturbed or rocky sites. It seems that the curves express the nature of their ecocline, by the hypotheses of some investigators, i.e. Random Niche hypothesis, Niche Pre-emption hypothesis, Lognormal distribution and Logarithmic series. The dominance concentration among the southern, northern and western slope, H'=1.282 at southern slope and H'=1.385 at western slope. Dominance-diversity curves of 16 sites showed Preston's lognormal distribution with small variations among them. It seems that the dominance diversity reflects the differences in the coenocline of their sites. The top 10 dominant species in species sequence of 113 tree species in whole the mountain, were noticed: Quercus mongolica, Pinus densiflora, Acer pseudo-siebold anum, Quercus serrata, Carpinus laxiflora, Styrax obassia, Fraxinus rhynchophylla, Tilia amurensis, Lindera obtusiloba and Abies holophylla in order.