• Structural Engineering and Mechanics
• /
• 제56권1호
• /
• pp.49-56
• /
• 2015

Dynamic compaction (DC) is a useful method for improvement of granular soils. The method is based on falling a tamper (weighting 5 to 40 ton) from the height of 15 to 30 meters on loose soil that results in stress distribution, vibration of soil particles and desirable compaction of the soil. Propagation of the waves during tamping affects adjacent structures and causes structural damage or loss of performance. Therefore, determination of the safe or critical distance from tamping point to prevent structural hazards is necessary. According to FHWA, the critical distance is defined as the limit of a particle velocity of 76 mm/s. In present study, the ABAQUS software was used for numerical modeling of DC process and determination of the safe distance based on particle velocity criterion. Different variables like alluvium depth, relative density, and impact energy were considered in finite element modeling. It was concluded that for alluvium depths less than 10 m, reflection of the body waves from lower boundaries back to the soil and resonance phenomenon increases the critical distance. However, the critical distance decreases for alluvium depths more than 10 m. Moreover, it was observed that relative density of the alluvium does not significantly influence the critical distance value.

• 대한기계학회논문집
• /
• 제19권7호
• /
• pp.1657-1664
• /
• 1995

For dynamic analysis of flexible structures, classical linear modeling has been widely used due to its several good aspects. However, it was found that the modeling often lost its accuracy. So, it is important to know the valid range of the modeling before it is used. more complicated modelings are needed to obtain reliable results only outside the valid range of the classical linear modeling. In this study, some rigid body motions of flexible structures which lead to the failure of the classical linear modeling are investigated. Hybrid deformation variable modeling, which is proved to be accurate in previous studies, is used to figure out the valid range of the classical linear modeling through numerical examples.

• Journal of Mechanical Science and Technology
• /
• 제16권7호
• /
• pp.896-901
• /
• 2002

This paper presents a nonlinear modeling method for dynamic analysis of flexible structures undergoing overall motions that employs the mode approximation method. This method, different from the naive nonlinear method that approximates only Cartesian deformation variables, approximates not only deformation variables but also strain variables. Geometric constraint relations between the strain variables and the deformation variables are introduced and incorporated into the formulation. Two numerical examples are solved and the reliability and the accuracy of the proposed formulation are examined through the numerical study.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.550-555
• /
• 2001

This paper presents a nonlinear modeling method for dynamic analysis of flexible structures undergoing overall motions that employs the mode approximation method. This method, different from the naive nonlinear method that approximates only Cartesian deformation variables, approximates not only deformation variables but also strain variables. Geometric constraint relations between the strain variables and the deformation variables are introduced and incorporated into the formulation. Two numerical examples are solved and the reliability and the accuracy of the proposed formulation are examined through the numerical study.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.518-522
• /
• 2014

This paper is concerned with the dynamic modeling of transmission line undergoing galloping vibrations. To this end, the kinetic and potential energies of a uniform wire vibrating in space are derived. The equations of motion suitable for numerical simulations are derived using the assumed mode method and Lagrange equation. The resulting equations of motion are expressed in matrix form. To cope with bundled transmission line, the spacer was modelled by a spring element. As a numerical example, a two-wire transmission line combined by spacers was considered. Natural vibration characteristics show that the in-plane vibrations of the transmission line appeared in low frequency range, which may lead to galloping.

• 소음진동
• /
• 제10권4호
• /
• pp.692-701
• /
• 2000

Escalators are widely used for mass transportation in public places. In recent years, strict requirements on the comfort and reliability for the public transportation have drawn a great attention to vibration in escalators. This paper presents a dynamic model for escalators to be used for the analysis and design of low vibration escalators. The dynamic model is developed so as to reflect the physical observation on peculiar characteristics in escalators such as the difference between up-moving and down-moving, and the abnormal vibration affected by the load applied. For validation of the dynamic model developed, experimental results are compared with numerical results from the model. The numerical study shows that the developed model may be useful for the analysis and design of escalator systems.

• Computers and Concrete
• /
• 제26권3호
• /
• pp.227-237
• /
• 2020

Strain rate investigations are needed to calibrate strain-rate-dependent material models and numerical codes. An appropriate material model, which considers the rate effects, need to be used for proper numerical modeling. The plastic concrete cut-off wall is a special underground structure that acts as a barrier to stop or reduce the groundwater flow. These structures might be subjected to different dynamic loads, especially earthquake. Deformability of a structure subjected to dynamic loads is a principal issue which need to be undertaken during the design phase of these structures. The characterization of plastic concrete behavior under different strain rates is essential for proper designing of cut-off walls subjected to dynamic loads. The Cowper-Symonds model, as one of the most commonly applied material models, complies well with the behavior of a plastic concretes in low to moderate strain rates and will be useful in explicit dynamics simulations. This paper aims to present the results of an experimental study on mechanical responses of one of the most useful types of plastic concrete and Cowper-Symonds constant determination procedures in a wide range of strain rate from 0.0005 to 107 (1/s). For this purpose, SHPB, uniaxial, and triaxial compression tests were done on plastic concrete samples. Based on the results of quasi-static and dynamic tests, the dynamic increase factors (DIF) of this material in different strain rates and stress state conditions were determined for calibration of the Cowper - Symonds material models.

• Nuclear Engineering and Technology
• /
• 제55권8호
• /
• pp.3088-3101
• /
• 2023

A pressurized vessel-pipe-safety valve (PVPSV) combination is a commonly used configuration in nuclear power plants, and a good numerical model is essential for the system design, sizing and performance optimization. However, owing to the large-scale and cross-scale features, it is still a challenge to build a system level numerical model with both high accuracy and efficiency. To overcome this, a novel system level modeling method which can synthesize the advantages of various models is proposed in this paper. For system modeling, the analytical approach, the method of characteristics (MOC) and the surrogate model approach are respectively adopted to predict the dynamics of the pressure vessel, the connecting pipe and the safety valve, and different models are connected through data interfaces. With this system model, dynamic simulations were carried out and both the stable and the unstable system responses were obtained. For the model verification purpose, the simulation results were compared with those obtained from experiments and full CFD simulations. A good agreement and a better efficiency were obtained, verifying the ability of the model and the feasibility of the modeling method proposed in this paper.

• 한국정밀공학회지
• /
• 제18권8호
• /
• pp.87-95
• /
• 2001

Although asymmetric beams are widely used in industry, few research results are available on the dynamic modeling and analysis of structure including asymmetric beams. Asymmetric beams cause complicated vibration phenomena due to the inherent bending-torsion coupled vibration. In this paper, an exact dynamic element matrix for the bending-torsion coupled vibration of asymmetric beam is derived. The application of the derived exact dynamic element matrix is demonstrated by some illustrative examples wherein the natural frequencies by the proposed modeling method are compared with those available in the literature. Another numerical example is also illustrated which deals with a general beam with joints. The numerical study shows that the exact dynamic element model is useful for the dynamic analysis of asymmetric bending-torsion coupled beams.

• 한국지반공학회논문집
• /
• 제32권4호
• /
• pp.5-14
• /
• 2016

건조토 지반에 근입된 지반-말뚝 시스템의 동적 거동을 정확히 예측하기 위해 3차원 수치 모델링을 수행하였다. 제안된 모델은 강진 시 지반의 비선형 거동을 적절하게 모사하기 위해 상용 유한 차분 프로그램인 FLAC3D를 이용하여 시간 영역에서 해석이 수행되었다. 모델링 방법론으로써 지반 구성 모델은 Mohr-Coulomb 탄소성 모델을 적용하였으며 지반 전단 탄성 계수의 비선형적인 감소를 모사할 수 있는 이력 감쇠 모델을 적용하였다. 진동 시 지반-말뚝 간의 완전 접촉, 미끄러짐, 분리 현상을 모두 모사하는 경계요소 모델을 적용하였으며 경계요소 모델을 구성하는 스프링 계수는 탄성이론에 기초하여 결정되어, 내장 함수인 FISH를 통해 깊이에 따라 연속적으로 입력되었다. 경계 조건의 경우, 지반-말뚝 상호작용의 영향을 받는 근역 지반만 메쉬를 생성하고 근역 지반의 경계부에 원역 지반의 가속도-시간 이력을 입력하는 방식인 단순화 연속체 모델링 기법(Kim et al., 2012)을 적용함으로써 해석 효율을 증가 시키고자 하였으며 적절한 최대지반탄성계수와 항복 깊이의 설정으로 지반의 비선형 거동을 더욱 정확히 모사하고자 하였다. 수치 해석의 오차를 최소화하고 모델의 신뢰성을 확보하기 위해, Yoo(2013)이 수행한 원심모형시험 결과와 수치 해석 결과와의 비교를 통해 제안된 기법의 캘리브레이션을 수행하였으며, 말뚝 최대 휨 모멘트와 말뚝 횡방향 최대 변위의 깊이 별 분포가 다양한 입력 하중 조건에서 실험 결과를 적절히 모사하고 있는 것을 확인하였다. 또한, 제안된 수치 모델의 적용성 평가를 위해 다른 실험 결과와의 비교 검증을 수행하였다.