• Journal of Power Electronics
• /
• v.15 no.2
• /
• pp.419-430
• /
• 2015

Flux estimation is a significant foundation of high-performance control for DC-excited synchronous motor. For almost all flux estimators, such as the flux estimator based on phase locked loop (PLL), DC drift causes fluctuations in flux magnitude. Furthermore, significant dynamic error may be introduced at transient conditions. To overcome these problems, this paper proposes an improved flux estimator for the PLL-based algorithm. Filters based on the generalized integrator are used to avoid flux fluctuation problems caused by the DC drift at the back electromotive force. Programmable low-pass filters are employed to improve the dynamic performance of the flux estimator, and the cutoff frequency of the filter is determined by the dynamic factor. The algorithm is verified by a 960V/1.6MW industrial prototype. Simulation and experimental results show that the proposed estimator can estimate the flux more accurately than the PLL-based algorithm in a cycloconverter-fed DC-excited synchronous machine vector control system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.6A
• /
• pp.820-831
• /
• 1999

In this paper, we have compared the performance of a D-TDMA protocol with that of a CDMA protocol, in radio access system for integrated voice/data services.The D-TDMA protocol is based on a generic dynamic channel assignment approach to be followed a combination of “circuit mode” reservation for voice calls, along with dynamic first-come-first served assignment of remaining capacity for data messages. In the CDMA protocol, we have used the voice activity detection to reduce the interface power of other mobiles in internal and external cells, and analyzed the interference power ratio. Also we have computed BER(Bit Error Rate) by using this interference power ratio and evaluated voice blocking probability(voice packet loss probability) and data transmission delay, according to average data length and average data arrival rate.We have found the CDMA protocol achieves comparatively higher performance for short data length, regardless of data arrival rate. Otherwise, the data transmission delay of D-TDMA protocol is shorter than that of the CDMA protocol for long data message.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.25-30
• /
• 2002

To reduce the vibration of a gear driving system, the modification of gear tooth from the orignal involute gear profile is usually done in gear manufacturers. The quantity of tooth modification has been decided on the basis of the interference between two gear teeth during gear meshing and the elastic deformation due to loading. However, the dynamic characteristics with tooth modification has to be investigated to avoid the instability to the variation of gear meshing stiffness and the nonlinearity due to gear backlash which results in sub- or super-harmonics in its responses. This research shows the dynamic characteristics with various tooth modifications in its type and quantity.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.13 no.9
• /
• pp.688-693
• /
• 2003

To reduce the vibration of a gear driving system. the modification of gear tooth from the orignal involute gear profile is usually done in gear manufacturers. The quantity of tooth modification has been decided on the basis of the interference between two gear teeth during gear meshing and the elastic deformation due to loading. However. the dynamic characteristics with tooth modification has to be investigated to avoid the instability to the variation of gear meshing stiffness and the nonlinearity due to gear backlash which results in sub- or super-harmonics in its responses. This research shows the dynamic characteristics with various tooth modifications in its type and quantity.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.608-611
• /
• 2005

As the optical communication industry is developed, the demand of optical communication part is increasing. $ZrO_2$ ceramic ferrule is very important part which can determines the transmission efficiency and information quality to connect the optical fibers. In general $ZrO_2$ ceramic ferrule is manufactured by grinding process because the demands precision is very high. For the precision grinding machining, it is very important that the error of feeding system is improved. Therefore, we estimated the dynamic characteristics in feeding system of ultra precision co-axial grinding machining system. Then, we performed the machining characteristics experiment.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.24 no.3
• /
• pp.320-326
• /
• 2015

Despite the wide industrial applications of planetary gear trains, the relationship between the design parameters (tooth profile, carrier mass, etc.) and performance (strength, vibration, noise, etc.) remains poorly understood. A significant amount of research has focused on transmission errors, which are measurable performance indicators directly related to the design parameters. Herein, an experimental test rig for a single-stage planetary gear set built using digital angular encoders and gap sensors is described. To study the static and dynamic characteristics of this planetary gear train, the transmission errors and sun gear orbit are analyzed from the data measured under various levels of torque and speed. The transmission errors of the gear train decrease 40% when the speed increases from 30 to 600 rpm with an output torque of 39.2 Nm, and increase 22% when the output torque increases from 19.6 to 39.2 Nm with an input speed of 30 rpm.

• Journal of Drive and Control
• /
• v.18 no.2
• /
• pp.46-55
• /
• 2021

A forklift is a powered industrial vehicle used to lift and move materials over short distances. Nowadays, almost all forklifts are equipped with an automatic transmission due to its improved operator comfort and increased productivity. Thanks to marked improvement of transmission control unit equipped with highly-advanced microcontrollers, recently developed automatic transmission for forklift have various auxiliary functions such as creep, auto retardation, and automatic shift with excellent shift quality. This paper deals with the creep function which enables one to maneuver a forklift at the designated low speed by slip control of clutches. The design of creep function was based on four modes of creep operation depending on the status of the operator's shift lever and accelerator pedal. Control algorithms and control parameters for each mode were designed to achieve the desired static and dynamic performance. Vehicle test for the designed creep function was carried out with an independently developed embedded controller. Test results confirmed good creep speed control without speed error at a steady state with a mild shift shock during mode changes by stepping or releasing the accelerator.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.06a
• /
• pp.809-810
• /
• 2008

• Journal of KSNVE
• /
• v.11 no.1
• /
• pp.82-88
• /
• 2001

In a transmission or geared rotor system a coupled phenomenon of lateral and torsional vibrations may occur due to the gear meshing effect. Particularly, in high speed or low vibration and low noise applications of geared rotor systems a coupled rotordynamic analysis is required to precisely predict their dynamic characteristics. In this paper a generalized finite element model of a gear pair element is developed, which actively couples the lateral and torsional vibrations due to the gear meshing effect. In the modeling the generalized forces due to the transmission error. geometrical eccentricities. and unbalances in the gear system are also considered. Then. using the developed gear pair element model a coupled unforced rotordynamic analysis is performed with a prototype 800 RT turbo-chiller rotor-bearing system having a hull-pinion speed increasing gear. Results show that the torsional vibration characteristics experience some changes due to the gear meshing and lateral dynamic coupling effect, but that they have no adverse effect and the lateral ones have no practical changes in an operating speed range.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.11 no.1
• /
• pp.3-12
• /
• 2001

In this paper, a synchronized stream encryption system for secure link layer communication in a radio channel is designed. Interleaving scheme which is used to enhance the transmission performance over a fading channel is applied to the encrypted information. A designed synchronous scream cipher system consists of a keystream generator, a synchronization pattern generator and a session key generator. The structure of a synchronous stream cipher system with periodic synchronization is composed of the encrypted information which consists of a synchronization pattern, an error correcting coded session key, an encrypted data in a period of synchronization. In this paper, interleaving scheme using dynamic allocation a1gorithm(DAA) is applied the encrypted information. The BER of the DAA has been slightly higher than that of the SAA(static allocation algorithm).