• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.3
• /
• pp.14-19
• /
• 2010

Partial anodic oxidation of Ti-mesh with a wire diameter of ~200[${\mu}m$] produces self-aligned $TiO_2$ nanotube arrays (~50[${\mu}m$] in length) on Ti-mesh substrate. The electrolyte used for anodic oxidation was an ethylene glycol solution with an addition of 1.5 vol. % $H_2O$ and 0.2 wt. % $NH_4F$. A dye-sensitized solar cell utilizing the photoanode structure of $TiO_2$-nanotube/Ti-mesh was fabricated without a transparent conducting oxide (TCO) layer, in which Ti-mesh replaced the role of TCO. The 1.93[%] photoconversion efficiency was low, which can be attributed to both insufficient dye molecules attachment and limited electrolyte flow to dye molecules. The optimized nanotube diameter and length as well as the $TiCl_4$ treatment can improve cell performance.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3272-3278
• /
• 2010

Synthesis and structural characterization of peripherally ferrocene-substituted zinc phthalocyanine (ZnPc-Fc) were carried out for efficient far-red/near-IR performance in dye-sensitized nanostructured $TiO_2$ solar cells. Incorporating ferrocene into phthalocyanine strongly improved the dye solubility in polar organic solvents, and reduced surface aggregation due to the steric effect of bulky ferrocene substituents. The involvement of electron transfer reaction pathways between ferrocene and phthalocyanine in ZnPc-Fc was evidenced by completely quenched fluorescence from S1 state (< 0.08% vs ZnPc). Strong absorption bands at 542 and 682 nm were observed in the transient absorption spectroscopy of ZnPc-Fc in DMSO, which was excited at a 670 nm laser pulse with a 15 ps full width at half maximum. Also, the excited state absorption signals at 450 - 600 and 750 - 850 nm appeared from the formation of charge separated state of phthalocyanine's anion. The lifetime of the charge separate state in ZnPc-Fc was determined to be $170{\pm}8$ ps, which was almost 17 times shorter than that of the ZnPc.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.380-383
• /
• 2015

We prepared the $TiO_2$ layer with 0 ~ 4 wt% of polystyrene (PS) beads having a radius of 250 nm to increase the dye adsorption and energy conversion efficiency (ECE) of a dye sensitized solar cell (DSSC). Then, we fabricated DSSCs using $0.45cm^2$ active area. FE-SEM was used to characterize the microstructure consisting of $TiO_2$ layer and PS beads. UV-VIS-NIR was used to determine the optical absorbance of working electrodes (WEs). Solar simulator and potentiostat were used to determine the photovoltaic properties. We observed that pores having a radius of 250 nm were formed with the density of $0.15ea/{\mu}m^2$ in $TiO_2$ layers after conducting the sintering process. The absorbance in visible light regime was found to increase with the increase in the amount of PS beads. The ECE increased from 4.66% to 5.25% when the amount of PS beads was increased from 0 to 4 wt%. This is because the pores of PS beads increased the adsorption of dye. Our results indicate that the ECE of the DSSCs can be enhanced by the addition of an appropriate amount of PS beads into $TiO_2$ layers.

• Applied Chemistry for Engineering
• /
• v.16 no.2
• /
• pp.159-168
• /
• 2005

Dye-sensitized solar cells (DSCs) have been under investigation for the past decade due to their attractive features such as high energy conversion efficiency and low production costs. The basis for energy conversion is the injection of electrons from a photoexcited state of a dye sensitizer into the conduction band of the nanocrystalline $TiO_2$ semiconductor upon absorption of light. It is believed that the DSC is one of the most promising candidates for renewable energy sources. In this review, the development trends and perspectives of DSCs are investigated.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.2
• /
• pp.251-256
• /
• 2006

To design the effective usage of electric double layer capacitors (EDLCs) used for a storage device of dye sensitized solar cell (DSC) energy, we first investigated the accumulation state of electrical charges and the charge behavior in the EDLCs. Based on the results, the voltage characteristics of EDLCs connected to DSC energy were evaluated. The results showed that the charge accumulation region concentrated on the central part of the carbonaceous electrode in EDLCs and the required times for charging and discharging were almost the same.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.134-134
• /
• 2009

We studied electrochemical properties of $TiO_2$ photoelectrode based graphene for dye-sensitized solar cells(DSSC). Gaphene has good electric conductivity and it is very good transparent when this is coated on monolayer. we prepared photoelectrode by squeeze methode and researched photoelectrical properties of $TiO_2$ electrode base gaphene. DSSC based on graphene was obtained conversion efficiency of 5.4% under irradiation of AM 1.5(100 $mWcm^2$).

• Bulletin of the Korean Chemical Society
• /
• v.32 no.5
• /
• pp.1579-1582
• /
• 2011

Alumina particles wrapped in few-layer graphene sheets were prepared by calcining aluminum nitride powders under a mixed gas flow of carbon monoxide and argon. The graphene sheets were characterized by powder X-ray diffraction (XRD), Raman spectroscopy, electron energy loss spectroscopy, and high-resolution transmission electron microscopy. The few-layer graphene sheets, which wrapped around the alumina particles, did not exhibit any diffraction peaks in the XRD patterns but did show three characteristic bands (D, G, and 2D bands) in the Raman spectra. The dye-sensitized solar cell (DSSC) with the alumina particles wrapped in few-layer graphene sheets exhibited significantly improved overall energy-conversion efficiency, compared to conventional DSSC, due to longer electron lifetime.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.147-149
• /
• 2005

Synthesis of $TiO_2$ nanoparticle paste is one of the important technologies in dye-sensitized solar cells (DSSC). Performances of the DSSCs from synthesized $TiO_2$ nanoparticle paste was similar or better than those from commercial sources. In addition. cell efficiency was further improved by using large scattering $TiO_2$ particles. Those results was utilized in manufacturing high efficiency DSSC modules.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.419-421
• /
• 2008

Sputter deposition on a Pt counter electrode was studied using RF plasma as the improvement of conversion efficiency for dye-sensitized solar cells (DSC). The effects of the sputtering thickness and incident angle on a Pt counter electrode for DSC was scrutinized. We conducted the experiment to get the optimal sputtering time for the performance of the DSC. Under the sputtering time condition of 120 seconds, we varied the incident angles of substrate from $0^{\circ}$ to $60^{\circ}$. Under standard test condition (AM 1.5, 100mW/$cm^2$), we obtained the maximum efficiency of 4.61% at the incident angle of $40^{\circ}$ with an active cell area of $1cm^2$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.425-427
• /
• 2008

Active area of dye-sensitized solar cell (DSSC) has an effect on the efficiency of DSSC. As the active area increases, the efficiency goes down in a general way. This is caused by the increase of internal resistance in DSSC. The internal resistances are related to various resistant elements. The charge transfer processes at Pt counter electrode and the sheet resistance of TCO are two of these resistant elements. In this study, we try to divide the active area into several small sections in a large sized cell to reduce these two internal resistant elements. As a result, we find out that the fill factor is increased and then the conversion efficiency is improved as the number of dividing active area into several small sections is increased.