• Bulletin of the Korean Chemical Society
• /
• v.32 no.8
• /
• pp.2633-2636
• /
• 2011

A new type of ionic liquid based on N-(3-aminepropyl)imidazolium iodide, called IIQAI, which consists of imidazolium and quaternary ammonium salt, and APII-(hydroxyethyl, propyl, hexyl) were synthesized and used as ionic liquid in dye-sensitized solar cells. APII-hexyl is solid, whereas IIQAI, APII-(hydroxyethyl, propyl) are viscous liquids. The synthesized ionic liquid showed relative thermal stability compared to the commercial ionic liquid of DMII. Among them, IIQAI was more stable than the other ionic liquid because of the two salt groups. APII-hydroxyethyl, which contains two hydroxyl groups, showed low viscosity with good flow. New types of ionic liquids were examined by $^1H$-NMR spectroscopy, thermo gravimetric analysis (TGA). IIQAI enabled a solar energy conversion efficiency of 6.3%, which is slightly higher than that of the referenced (DMII, 6.2%).

• Textile Coloration and Finishing
• /
• v.15 no.2
• /
• pp.86-92
• /
• 2003

It is already known that the color of wool fabric dyed with disazo acid dyes could be changed in dyeing process and this is accelerated under alkaline condition. Focus was given to figuring out the mechanism of this color change, through the LC-MS analysis. In this study, no color change was seen in wool fabrics dyed with C. I. Acid Blue 113 under weak acidic, neutral and weak alkaline conditions for 1hour. However, the wool fabrics dyed under weak alkaline condition for a long time over 3 hours fumed reddish orange. When the wool fabrics dyed under weak acidic, neutral and weak alkaline conditions were treated with $0.5g/L\;Na_2C0_3$ solution, all of them turned reddish orange. On the other hand, the color of silk fabrics dyed with C. I. Acid Blue 113 were not changed after the same alkaline treatment. Wool contains cystine and cysteine, whereas silk does not. Due to the reversible reduction/oxidation process of cystine and cysteine in wool dyeing, the C. I. Acid Blue 113 of the dis-azo type is decomposed by reduction and consequently turned them into the reddish orange mono-azo types dye.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.100-106
• /
• 2009

A novel 8 V DC power source with an external series-parallel connection of 50 Dye-sensitized Solar Cells (DSCs) has been proposed. One DSC has the optimized length to width ratio of $5.2{\times}2.6\;cm$ and an active area $8\;cm^2$ ($4.62{\times}1.73\;cm$) which attained a conversion efficiency of 4.02%. From the electrochemical impedance spectroscopic analysis, it was found that the resistance elements related to the Pt electrode and electrolyte interface behave like that of diode and the series resistance corresponds to the sum of the other resistance elements. Surface morphology and sheet resistance of Pt counter electrode did not degrade the performance of the cell. This novel 8V-0.33A DC power source shows stable performance with an energy conversion efficiency of 4.24% under 1 sun illumination (AM 1.5, Pin of $100\;mW/cm^2$).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.445.1-445.1
• /
• 2014

Dye-sensitized solar cells (DSSCs) have been widely investigated as a next-generation solar cell because of their simple structure and low manufacturing cost. The $TiO_2$ film with thickness of $8{\sim}10{\mu}m$, which consists of nanoparticles, acts as both a scaffold with a high surface-to-volume ratio for the dye loading and a pathway to remove the electrons. However, charge carriers have to move across many particle boundaries by a hopping mechanism. So, one dimensional nanostructures such as nanotubes, nanorods and nanowires should improve charge carrier transportation by providing a facile direct electron pathway and lowering the diffusion resistance. However, the efficiencies of DSSCs using one dimensional nanostructures are less than the $TiO_2$ nanoparticle-based DSSCs. In this work, the patterned $TiO_2$ film with thickness of $3{\mu}m$ was deposited using photolithography process to decrease of electron pathway and increase of surface area and transmittance of $TiO_2$ films. Properties of the patterned $TiO_2$ films were investigated by various analysis method such as X-ray diffraction, field emission scanning electron microscopy (FESEM) and UV-visible spectrophotometer.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.18 no.4
• /
• pp.77-86
• /
• 2016

In order to analysis on color difference of natural dyes, I have dyed Hanji, cotton, silk fabric and exposed them to carbon arc light. The results of experiment have been analysed by Munsell's value, and compared the difference of colors which were recognized visually. Gardenia Jasminoides is monogenetic dye, but it gained darker color by pre-mordanting method used aluminum mordant agent and greenish yellow color by ferric mordant agent. whereas Curcuma, an Amur cork, and bud of pagoda tree are shown as greenish yellow color, and A barberry root, Betel nut, and Rhubarb are shown as reddish yellow color. these gained khaki colored dyed fabric by ferric mordanting. In addition, Sappan wood showed great result in pre-mordanting. Especially, it gained dark red color by aluminum pre-mordanting. The pink color was shown by post-mordanting. and Logwood showed great dyeing result in Hanji and cotton better than silk. Specially pre-mordanting was effective. Hanji and cotton showed greenish blue color by aluminum pre-mordanting, and silk showed brown color. However the color, which was recognized visually, differed from colorimeter sometimes. Therefore, such color table might be necessary for the natural dyeing.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.10a
• /
• pp.124-127
• /
• 2008

Dye-sensitized solar cells (DSCs) have been proposed as a substitute for overcoming the limitation of Si solar cells because DSC has the various applications using advantages of DSC such as low cost, transparency and flexibility. Although some people point out low efficiency of DSC as the important problem at present, general views say that actually cumulative power is not insufficient as compared with Si solar cell. Therefore, we analyzed the characteristics of both cells according to the change of incident angle in this study. The insensibility about the incident angle has more developable time. Finally, DSC is able to fill a shortage of power caused from low efficiency of DSC for same time by developing during impossible time to develop in Si solar cell. As a result, DSC has 75% and 210% cumulative power of Si solar cell in summer and winter under the standard sunshine duration.

• Bulletin of the Korean Chemical Society
• /
• v.31 no.11
• /
• pp.3093-3098
• /
• 2010

The core-shell $SnO_2$@AO (A=Ni, Cu, Zn and Mg) films were prepared and the effects of coatings on photovoltaic properties were investigated. Studies on X-ray photoelectron spectroscopy, energy dispersive X-ray analysis and transmission electron microscopy showed the formation of divalent oxides on the surface of $SnO_2$ nanoparticles. It was commonly observed that all the dye-sensitized core-shell films exhibited higher photovoltage than the bare $SnO_2$ film. Transient photovoltage measurements confirmed that the improved photovoltages were related to the decreased time constants for electron recombination.

• Journal of Electrochemical Science and Technology
• /
• v.1 no.2
• /
• pp.75-80
• /
• 2010

We report Co-tetramethoxyphenylporphyrin on carbon particles (Co-TMPP/C) as a non-Pt catalyst for tri-iodide reduction in dye-sensitized solar cells (DSSCs). The presence of well-dispersed carbon and cobalt source in the catalyst surface is confirmed by transmission electron microscopy, scanning electron microscopy, and energy dispersive X-ray analysis. In the C 1s, Co 2p, and N 1s peaks measured by X-ray photoelectron spectroscopy, the C-N, Co-$N_4$, and N-C are assigned to the component at 285.7, 781.8, and 401 eV, respectively. Especially, the Co-TMPP/C shows improved current density, diffusion coefficient, and charge-transfer resistance in the ${I_3}^-/I^-$ redox reaction compared to conventional catalysts. Furthermore, in the DSSCs performance, the Co-TMPP/C shows increased short circuit current density, higher open circuit voltage, and improved cell efficieny in comparison with Pt/C.

• Fibers and Polymers
• /
• v.4 no.3
• /
• pp.124-128
• /
• 2003

Dark brown Alpaca fiber was reduced in shade via selective bleaching with peroxide. Two selective oxidative bleaching methods were tested on alpaca top to assess their effectiveness for color removal and fiber quality properties. Color change, bundle strength, weight loss, fiber diameter, surface modification, dye-ability and dye wash fastness were assessed for both methods and compared with the original brown top. Bleach method 1 (BL-I) showed little surface modification, 5.8% weight loss and 2.4% strength loss. D1925 yellowness index was reduced to 74.3 from 83.1 and provided a good base for the dyeing of medium to deep shades. Bleach method 2 (BL-II) displayed considerable surface modification, 7.8% weight loss and 18% strength loss. BL-II also resulted in a mean diameter reduction of 1.9 micron during bleaching. Yellowness was reduced to 64.5 from 83.1 and provided a very good base for the dyeing of medium to deep shades. BL-I showed better exhaustion of the premetallised dye Lanaset Violet B than BL-II. Wash fastness for BL-II was 1 grey scale unit poorer than BL-I. BL-II showed far better color clarity at pale depths however the wash fastness of the finished product was not good enough to maintain the depth or clarity of the color. BL-I showed poorer clarity of color but exhibited better wash fastness results.

• Journal of the Korean Ceramic Society
• /
• v.52 no.5
• /
• pp.384-388
• /
• 2015

We prepared blocking layers by adding 0.0 ~ 0.6 wt% nano diamond blends (DBs) to $TiO_2$ blocking layers to improve the energy conversion efficiencies (ECEs) of dye sensitized solar cells (DSSCs). TEM and micro-Raman spectroscopy were used to characterize the microstructure and phases of DBs, respectively. Optical microscopy and FE-SEM were used to analyze the microstructure of the $TiO_2$ blocking layer with DBs. UV-VIS-NIR spectroscopy was used to determine the absorbance of the working electrodes. A solar simulator and a potentiostat were used to determine the photovoltaic properties and the impedance of the DSSCs with DBs. From the results of the DBs analysis, we determined a 6.97 nm combination of nano diamonds and graphite. We confirmed that ECE increased from 5.64 to 6.48 % when the added DBs increased from 0.0 to 0.2 wt%. This indicates that the effective surface area and electron mobility increased when DBs were added to the $TiO_2$ blocking layer. Our results indicate that the ECE of DSSCs can be enhanced by adding an appropriate amount of DBs to the $TiO_2$ blocking layers.