• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.1
• /
• pp.90-97
• /
• 2014

In this paper, we have designed the antenna for Korea SAT-5 Satellite Communication which can use Ka band in the earth station. The antenna structure consist of the the dual-offset gregorian reflector that has high gain and efficiency, the corrugated horn that has symmetric radiation patterns and low side lobe levels, the iris polarizer that make circular polarization and the OrthoMode Transducer that separate transmitting and receiving signals. The designed antenna gain is more than 45.7dBi in Tx-band which use LHCP and 42.0dBi in Rx-band which use RHCP. The co-polarized and cross-polarized radiation pattern comply with ITU-R S.580-6 and S.731-1 that are recommended by International Telecommunication Union in the geostationary satellite. The Axial ratio is less than 1.0dB in Tx-band and 1.5dB in Rx-band that meet MIL-STD-188-164A.

• Journal of the Ergonomics Society of Korea
• /
• v.33 no.3
• /
• pp.241-253
• /
• 2014

Objective: The objective of this study was to examine multi-modal interaction effects of input-mode switching on the use of smart phones. Background: Multi-modal is considered as an efficient alternative for input and output of information in mobile environments. However, there are various limitations in current mobile UI (User Interface) system that overlooks the transition between different modes or the usability of a combination of multi modal uses. Method: A pre-survey determined five representative tasks from smart phone tasks by their functions. The first experiment involved the use of a uni-mode for five single tasks; the second experiment involved the use of a multi-mode for three dual tasks. The dependent variables were user preference and task completion time. The independent variable in the first experiment was the type of modes (i.e., Touch, Pen, or Voice) while the variable in the second experiment was the type of tasks (i.e., internet searching, subway map, memo, gallery, and application store). Results: In the first experiment, there was no difference between the uses of pen and touch devices. However, a specific mode type was preferred depending on the functional characteristics of the tasks. In the second experiment, analysis of results showed that user preference depended on the order and combination of modes. Even with the transition of modes, users preferred the use of multi-modes including voice. Conclusion: The order of combination of modes may affect the usability of multi-modes. Therefore, when designing a multi-modal system, the fact that there are frequent transitions between various mobile contents in different modes should be properly considered. Application: It may be utilized as a user-centered design guideline for mobile multi modal UI system.

• Journal of Positioning, Navigation, and Timing
• /
• v.6 no.4
• /
• pp.195-203
• /
• 2017

A 2U cube satellite called SNUGLITE has been developed by GNSS Research Laboratory in Seoul National University. Its main mission is to perform actual operation by mounting dual-frequency global positioning system (GPS) receivers. Its scientific mission aims to observe space environments and collect data. It is essential for a cube satellite to control an Earth-oriented attitude for reliable and successful data transmission and reception. To this end, an attitude estimation and control algorithm, Attitude Determination and Control System (ADCS), has been implemented in the on-board computer (OBC) processor in real time. In this paper, the Extended Kalman Filter (EKF) was employed as the attitude estimation algorithm. For the attitude control technique, the Linear Quadratic Gaussian (LQG) was utilized. The algorithm was verified through the processor in the loop simulation (PILS) procedure. To validate the ADCS algorithm in the ground, the experimental verification via a single axis Hardware-in-the-loop simulation (HILS) was used due to the simplicity and cost effectiveness, rather than using the 3-axis HILS verification (Schwartz et al. 2003) with complex air-bearing mechanism design and high cost.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.2170-2174
• /
• 2005

Selective Laser Sintering (SLS) is a useful rapid prototyping technique for the manufacture of three dimensional (3D) solid objects directly from a scanning data. A new approach called a Selective Multi-Laser Sintering (SMLS) system has been developed at Korea Institute Machinery & Materials (KIMM) as an industrial type SFFS. This SMLS machine is built with a frame, heaters, nitrogen supply part, laser system. This system uses the dual laser and 3D scanner made in $Solutionix^{TM}$ to improve the precision and speed for large objects. The three-dimensional solid objects are made of polyamide powder. The investigation on each part of SMLS system is performed to determine the proper theirs design and the effect of experimental parameters on making the 3D objects. The temperature of the system has a great influence on sintering the polymer. Because the stability of the powder temperature prevents the deformation of each layer, the controls of the temperature in both the system and the powders are very important during the process. Therefore, we simulated the temperature distribution of build room using the temperature analysis with ANSYS program. Selected radiant heater is used to raise temperature of powder to melting point temperature. The laser parameters such as scan spacing, scan speed, laser power and laser delay time affect the production the 3D objects too. The combination of the slow scan speed and the high laser power shows the good results without the layer curling. The work is under way to evaluate the effect of experimental parameters on process and to produce the various objects. We are going to experiment continuously to improve the size accuracy and surface roughness.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.4 s.334
• /
• pp.29-36
• /
• 2005

Many novel designs of planar antennas for related applications such as internal mobile phone antennas, base station antennas, WLAN or Bluetooth antennas, and so on, have been reported very recently, especially since the year 2000. In this thesis, Dualband internal antenna for GSM/DSC handset is proposed. The antenna has a size of about 38mm$\times$90mm$\times$1mm, giving a total mobile phone PCB for support and fold type Patch of about 30mm$\times$8mm$\times$3.2mm. This antenna characteristic facilitates the fine-tuning of the two operating frequencies of 909MHz and 1762MHz in this dualband design. The measured radiation pattern in the E-plane and H-plane for operating frequencies of 909MHz and 1762MHz is compared and analyzed. The designed and fabricated two band internal antenna for GSM/DSC handset have a gain between 0dBi and 2.0dBi at all bands.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.2
• /
• pp.108-116
• /
• 2002

In this paper, to improve bandwidth of microstrip antenna, we discussed the patch structure using dual patch and probe feed. To provide PCS service and IMT-2000 service simultaneous, a microstrip patch antenna needs impedance bandwidth of 22%. We propose wide-band microstrip path antenna without complexity. To analyze characteristics of microstrip patch antenna, we used Ensemble of commercial software. The microstrip patch antenna was designed, fabricated, and tuned. The result was that 500 ㎒(25.5%) of impedance bandwidth for VSWR 2,430 ㎒(21.9%) of impedance bandwidth for VSWR 1.5. The microstrip patch antenna has side lobe of -14 dB. The front to back ratio is 20 dB overall. The measured gain of the microstrip patch antenna is 5.2 dBi.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.2
• /
• pp.83-90
• /
• 2000

In this paper, a stacked circular-disk microstrip 1${\times}$4 array antenna was designed and manufactured and tested to apply in next generation mobile communication, on IMT-2000 system(up-link: 1.885 GHz∼2.025 GHz, down-link: 2.11 GHz∼2.2 GHz) base station which has dual frequency, broadband and high-gain characteristics. The experimental results are as follows : resonant frequency of 1.885 GHz and 2.178 GHz VSWR (1.064 , 1.432), return loss (-30.19 dB , -24.99 dB), band width (VSWR<2) are 402 MHz, -3dB beam width at radiation pattern are ${\alpha}$E-16.8$^{\circ}$, ${\alpha}$H-69$^{\circ}$(1.885 GHz) and ${\alpha}$E-l5.2$^{\circ}$, ${\alpha}$H-51.5$^{\circ}$(2.178 GHz), gain(13.7 dBi∼15.21 dBi).

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.1
• /
• pp.68-75
• /
• 2007

A single chip NFC transceiver supporting not only NFC active and passive mode but also 13.56MHz RFID reader and tag mode was designed and fabricated. The proposed NFC transceiver can operate as a RFID tag even without external power supply which has dual antenna structure for initiator and target. The area increment due to additional target antenna is negligible because the target antenna is constructed by using a shielding layer of initiator antenna. The analog front end circuit of the proposed NFC transceiver consists of a transmitter and receiver of reader/writer block supporting NFC initiator or RFID reader mode, and a tag circuit for target of passive NFC mode or RFID tag mode. The maximum baud rate of the proposed NFC device is 212kbps by using UART serial interface. The chip has been designed and fabricated using a Magnachip's $0.35{\mu}m$ double poly 4-metal CMOS process, and the effective area of the chip is 2200um by 3600um.

• Journal of ILASS-Korea
• /
• v.13 no.4
• /
• pp.212-219
• /
• 2008

To develop the twin-fluid atomizer having the excellent performance of painting, the spray characteristics of how a wide area can be painted efficiently by one time spraying were studied in this paper. Spray phenomena are affected by the many factors determining the spray field such as the spraying pressure of gas, the spraying pressure and viscosity of liquid paints, the opening duration of needle valve, the design dimension of nozzle, and so on. As the results of experiments, these factors affecting on spray characteristics were suggested as followings; 1) The optimum spraying pressure of gas was $0.015{\sim}0.02\;kPa$, and the appropriate spraying pressure of liquid paint was 0.01kPa, In these situations, the setting up pressures must be compensated as much as the losing amount of pressure because a decompression occurred when operating valves. 2) The duration of opening the needle valve must be sustained for $1{\sim}2$ seconds to inject gas after spraying the liquid paint. This operating of the needle valve was necessary to avoid the affect on the changing of liquid column length, and to prevent the droplet deposit at the initial time of spraying. 3) The spray tip penetration was gained form the experimental equation, and the effective spraying angle was $85^{\circ}{\pm}5^{\circ}$ just at he appropriate spraying pressure of gas. The distribution of the area sprayed had the variation in $350{\pm}50\;mm$ because of the spraying pressure of gas, the its distance from the spray tip, and the lift of the needle valve.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.12
• /
• pp.3681-3689
• /
• 2013

This study explored a direct SET-photochemical strategy to construct a new family of thioene conjugated-naphthalamide fluorophore based lariat-crown ethers which show strong binding properties towards heavy metal ions. Irradiations of designed nitrogen branched (trimethylsilyl)methylthio-terminated polyethylenoxy-tethered naphthalimides in acidic methanol solutions have led to highly efficient photocyclization reactions to generate naphthalamide based lariat type thiadiazacrown ethers directly in chemo- and regio-selective manners which undergo very facile secondary dehydration reactions during separation processes to produce their corresponding amidoenethio ether cyclic products tethered with electron donating diethyleneoxy- and diethyenethio-side arm chains. Fluorescence and metal cation binding properties of the lariat type enamidothio products were examined. The photocyclized amidoenethio products, thioene conjugated naphthalamide fluorophore containing lariat-thiadiazacrowns exhibited strong fluorescence emissions in region of 330-450 nm along with intramolecular exciplex emissions in region of 450-560 nm with their maxima at 508 nm. Divalent cation $Hg^{2+}$ and $Pb^{2+}$ showed strong binding to sulfur atom(s) in side arm chain and atoms in enethiadiazacrown ether rings which led to significant enhancement of fluorescence from its chromophore singlet excited state and concomitant quenching of exciplex emission. The dual fluorescence emission responses towards divalent cations might provide a new guide for design and development of fluorescence sensors for detecting those metals.