• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.69-72
• /
• 2011

The ground tests of the dual pulse solid rocket motors(SRM) were performed to prove the performance of the developed dual pulse solid rocket motors. To achieve dual pulse, pulse seperation device(PSD) and independent ignition systems were installed between the 1st pulse motor and the 2nd pulse motor. The three major development goals are as follow. First, the total impulse of the dual pulse SRM must be over 90% of the single SRM which has same envelopment and weight. Second, the ignition of the 2nd pulse motor can be started at any time between 0 and 60 seconds after termination of the 1st pulse motor. Last, the rupture disk of PSD must not be broken at the 1st pulse pressure, but be broken at below 30% of the 2nd pulse operating pressure. The results of the ground tests satisfied the development goals.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1048-1057
• /
• 2015

This paper proposes a sensorless speed control algorithm for parallel-connected dual Surface-mounted Permanent Magnet Synchronous Motors (SPMSMs) fed by a single inverter. For stable parallel operation of synchronous motors with a single inverter, each motor has to be constantly kept in the synchronization state regardless of load torque. If the master motor with the larger load is controlled, the synchronous state will be maintained. Therefore, detection of the master motor is essential. Conventionally, the master motor is determined by comparing the rotor position error from the relation between the back-EMF for torque angle and the flux position; consequently, the position sensor is deemed essential for finding the rotor position. The parallel sensorless speed control method proposed in this paper uses no position sensor, instead it compares the flux-axis current from the connection between the back-EMF for torque angle and current in unbalanced load conditions. The results of simulation and experiment conducted verify the efficacy of the proposed method.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.7
• /
• pp.39-46
• /
• 2008

High precision machining technology has become one of the important parts in the development of a precision machine. Such a machine requires high speed on a large workspace as well as high precision positioning. For machining systems having a long stroke with ultra precision, a dual-stage system including a global stage (coarse stage) and a micro stage (fine stage) is designed in this paper. Though linear motors have a long stroke and high precision feed drivers, they have some limitations for submicron positioning. Piezo-actuators with high precision also have severe disadvantage for the travel range, and the stroke is limited to a few microns. In the milling experiments, the positional accuracy has been readily achieved within 0.2 micron over the typical 20 mm stroke, and the path error over 2 micron was reduced within 0.2 micron. Therefore, this technique can be applied to develop high precision positioning and machining in the micro manufacturing and machining system.

• Journal of Mechanical Science and Technology
• /
• v.16 no.12
• /
• pp.1664-1672
• /
• 2002

Gantry mechanisms have been widely used for precision manufacturing and material handling in electronics, nuclear, and automotive industries. Dual-drive servo mechanism is a way to increase control bandwidth, in which two primary axes aligned in parallel are synchronously driven by identical servo motors. With this mechanism, a flexible coupling (compliance mechanism) is often introduced in order to avoid the damage by the servo mismatch between the primary drives located at each side of gantry. This paper describes the design guidelines of the dual-drive servo mechanism with focus on its dynamic characteristics and control ramifications. That is, the effect on the system bandwidth which is critical on the system performance, the errors and torques exerted on guide ways in case of servo mismatch, the vibration characteristics concerned with dynamic error and settling time, and the driving force required at each axis for control are thoroughly investigated.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.25 no.3
• /
• pp.269-275
• /
• 1988

In this paper, a high efficiency motor drive system which improves the multi-step response of PM step motors by reducing the transition time of the motor drive current, is studied by designing a dual-voltage drive circuit. The designed drive circuit eventually prevents the motor from decreasing drive torque while the stepping rate is increased. The method of designing a dual-voltage drive circuit with the motor specifications is suggested in order to improve the response of step rate and drive efficiency. Also, despite improving the power efficiency on motor driving, the response characterstics suggested by the motor manufacture's specifications are satisfied without any special deficiency.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.664-667
• /
• 2010

Solid rocket propulsion systems are generally used for tactical missiles due to the structural and operational simplicity. Nevertheless, various kinds of design factors including outer diameter, length, weight, loading efficiency of propellant grain effects to thrust performance. Dual thrust is beneficial to range extension and terminal velocity increasement. But loading efficiency becomes low in case to obtain dual thrust performance by burning surface control. So, It is predicted to be reasonable to obtain dual thrust performance with high/low burning rate propellants. This study is on internal ballistic analysis and ground test to confirm dual thrust performance.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.2
• /
• pp.216-224
• /
• 2013

This paper describes dual inverter drive for a fractional-slot concentrated winding permanent magnet synchronous machine (PMSM). PMSMs are widely used in many applications from small servo motors to few megawatts generators thanks to its high efficiency and torque density. Especially, fractional-slot concentrated winding PMSM is very popular in the applications where wide operation range is required because it shows very wide constant power speed ratios. High speed operation, however, requires lots of negative daxis current for reducing back-EMF regardless of output torque. Field weakening current does not contribute to the torque generation in surface mounted PMSM case and causes inverter and copper loss. To reduce the losses from field weakening current, this paper proposes PMSM with split stator and parallel dual inverter drive. Proposed parallel dual inverter drive reduces back-EMF and enables efficient drive at high speed and light load situation. Control strategy of proposed dual inverter system is established through loss analysis and simulation. Proposed concept is verified with practical experiment.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.5
• /
• pp.1908-1916
• /
• 2018

This paper proposes a controller design method for suppressing the resonance generated in the slave motor in the middle and low speed operation range, according to the load and parameter differences between two motors, during parallel operation using the master and slave method that controls two surface permanent magnet synchronous motors connected in parallel by a single inverter. The proposed resonance suppression controller is directly obtained by analyzing the resonance characteristics, using the lead controller method. Therefore, it is possible to fundamentally reduce trial and error to set the controller gain. In addition, because the proposed resonance suppression controller was designed as a lead controller, the stability region of the system increased owing to the added zero point, making the system robust with respect to parametric variations. Simulations and experiments confirmed the usefulness of the proposed method and the system's robustness with respect to parametric variations.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.10a
• /
• pp.144-147
• /
• 2003

In order to evaluate spring-back behavior in automotive sheet forming processes, a panel shape idealized as a SS-rail has been investigated. After spring-back kas been predicted fer SS-rails using the finite element analysis, results has been compared with experimental measurements for three automotive sheets. To account for hardening behavior such as the Bauschinger and transient effects in addition to anisotropic behavior, the combined isotropic-kinematic hardening law based on the Chaboche type single-surface model and a recently developed non-quadratic anisotropic yield function have been utilized, respectively.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.3
• /
• pp.240-247
• /
• 2013

This paper proposes an optimal three-dimensional coordinate implementation of the vision sensor using two CCD cameras. The PBVS (Position based visual servoing) is implemented using the positional information obtained from images. Stereo vision by PBVS method that has enhanced every frame using calibration parameters is effective in the distance calculation. The IBVS (Image based visual servoing) is also implemented using the difference between reference and obtained images. Stereo vision by IBVS method calculates the distance using rotation angle of motors that correspond eyes and neck without enhanced images. The PBVS method is compared with the IBVS method in terms of advantages, disadvantages, computing time, and performances. Finally, the IBVS method is applied for the dual arm manipulator on the mobile inverted pendulum. The autonomous mobile inverted pendulum is successfully demonstrated using the center of the manipulator's mass.