• Journal of the Korean Society of Food Science and Nutrition
• /
• v.29 no.4
• /
• pp.561-567
• /
• 2000

This study was conducted to determine the effect of far infrared-vacuum drying on the quality changes of Pimpinella bracycarpa, such as drying efficiency (weight loss), color differences, browning degrees, rehydration and sensory evaluation. Wehn Pimpinella bracycarpa was dried for designated time at 5$0^{\circ}C$, 6$0^{\circ}C$ and 7$0^{\circ}C$, drying time of far infrared-vacuum drying was decreased more than 17% compared to that of infrared drying. The color changes increased as drying temperature increased and far infrared-vacuum drying made less color changes than infrared drying. Also, the total microbial counts and the number of yeast and mold were gradually reduced as drying temperature increased and drying time was longer, but there was no significant differences in microbial changes among drying methods. The rehydration rates of Pimpinella bracycarpa increased as drying temperature increased and was better at far infrared-vacuum drying than infrared drying. Also, according to the sensory evaluation after rehydration of Pimpinella bracycarpa, the hihger scores were obtained at lower temperature and far infrared-vacuum drying, especially the color was obtained much hihger score in the far infrared-vacuum drying than infrared drying. Thus, the results showed that drying efficiency and stability of rehydration and color changes was increased and the quality deterioration of Pimpinella bracycarpa could be minimized by using far infrared-vacuum drying.

• Science of Emotion and Sensibility
• /
• v.20 no.2
• /
• pp.117-126
• /
• 2017

In this study, moisture transport characteristics for the woven and knitted fabrics made of 8 kinds of fiber materials using MMT (moisture management tester) were measured and discussed with the Bireck bt MMT and water evaporating rate (WER) measuring methods, which are vertical moisture transport methods. In addition, the drying property by MMT of the eight kinds of specimens was compared and discussed with the results measured by the vertical drying measurement. MMT experimental result which is horizental moisture transport appeared to be similar to the result of the Bireck method, which is the vertical moisture transport experiment. Absortion time measured from drip method of the fabrics made of the bamboo, linen, and cotton/nylon composite fabrics was short and thus they showed best wicking property, which was attributed to the low contact angle on the fabric surface and high porosity of the fabrics due to the staple yarn structure composed of the hydrophilic staple fibers. In drying property of the fabric specimens by MMT, maximum absorption radius of the dry-zone knit and bamboo woven fabrics were the highest and they showed the best drying property, which was a little different result compared with vertical drying measurement method. Half time of the drying rate in the MMT method was highly correlated with the fabric thickness and saturated moisture absortion rate and their regression coefficients were 0.9 and 0.88, respectively. This means that the knitted and woven fabric design technology for retaining good wicking and drying properties of the fabrics with thin fabric thickness is very important for obtaining high functional wear comfort fabrics. In addition, wicking and drying properties of the fabrics made of different fiber materials and with different yarns and fabric structures showed different results according to the measuring methods.

• Culinary science and hospitality research
• /
• v.22 no.2
• /
• pp.104-114
• /
• 2016

In this study, the quality characteristics of different drying methods of Cirsium setidens Nakai, which contains large amounts of biological substances, were investigated for the improvement of their practical use. During the drying period, the weight reduction was the highest with hot-air drying(82.7%). As for the general component and mineral contents analysis results of Cirsium setidens Nakai, there were no significant difference. Cyclic low pressure drying resulted highest amount of total phenolic components and 1,1-diphenyl-2-picrylhydrazyl (DPPH). Hence, cyclic low pressure drying method is the best method for enhancing antioxidant activity of Cirsium setidens Nakai.

• Food Science of Animal Resources
• /
• v.32 no.5
• /
• pp.531-539
• /
• 2012

To determine the effects of various drying methods on the quality characteristics of beef jerky from low-valued cuts, Hanwoo beef shank muscles were either hot air-dried, shade-dried, or sun-dried. The physicochemical quality and microbiological safety of the Hanwoo beef jerky were analyzed during a storage of $25^{\circ}C$. Moisture content and water activity ($a_w$) of the samples decreased as the time period of storage increased, regardless of the drying condition (p<0.05). Shade-dried jerky showed higher $a_w$ compared to others after storage of 20 d (p<0.05). The pH value of hot air-dried jerky was higher than those of others (p<0.05). For color properties, sun-dried samples showed higher redness ($a^*$) and yellowness ($b^*$) compared with the properties of others (p<0.05). The hot air-dried jerky showed higher shear force values than the sun-dried or the shade-dried jerky after 10 and 20 d (p<0.05). However, the total plate counts (TPCs) of naturally dried jerky (shade and sundried) were higher than hot-air dried jerky after storage of 10 and 20 d (p<0.05). With regard to sensory properties, naturally dried jerky showed higher tenderness, juiciness, and overall acceptability scores than the hot air-dried jerky (p<0.05). In conclusion, although natural drying appears to be more susceptible to microbiological contamination than hot air-drying, the natural drying method seems to result in superior quality than the hot air drying method.

• Textile Coloration and Finishing
• /
• v.21 no.4
• /
• pp.23-32
• /
• 2009

The objective of this study is to investigate the efficacy of leaf powder colorants as substitutes for traditional indigo dyeing. Leaf powder colorants were prepared by hot air($50^{\circ}C$) and room temperanrre($25^{\circ}C$) drying methods from fresh leaves. The presence of indigo in the leaf powder colorants was confirmed by UV/Visible absorption spectra. All the powder colorants showed broad absorption at 602 nm as same as synthetic indigo. Dyeing was done by reduction method with sodium hydrosulfite and sodium hydroxide. Leaf powder colorants produced blue color on silk fabrics, showing similar color to the one dyed traditionally with fresh juice extract. The powder colorants prepared at room temperature drying were more stable for long term storage than that prepared by hot air drying. Thus, the powder colorants prepared by room temperature drying was reduced and dyed in one-step process without sodium hydroxide in the dyebath for further investigate dyeing properties. K/S value of the fabric dyed without sodium hydroxide was much higher than one dyed with sodium hydroxide. Regardless of the addition of sodium hydroxide, rubbing fastness was fairly good showing above 4 rating. Fastness to dry cleaning and light of the fabrics dyed without sodium hydroxide were mote higher than that dyed in alkaline condition.

• Korean journal of food and cookery science
• /
• v.16 no.1
• /
• pp.47-56
• /
• 2000

The purpose of this study was to develop a drying method of Gangjung. a traditional Korean snack, thus to reduce the drying time and to improve the quality of Gangjung. Two drying methods, hot air drying and far infrared ray drying were used by changing conditions such as air velocity(0.4, 1.2, 1.6 m/s), temperature(40, 50, 60$\^{C}$), and aging. Optimal moisture content of dried Gangjung pellet was 17% which was proper for frying. Cracks appeared on the surface of Gangjung pellet at lower levels of moisture content. Far infrared ray drying saved drying time about 20%. Both hot air drying and far infrared ray drying at 0.4 m/s of air velocity tended to show better quality of Gangjung than those dried at higher air velocities. The expansion volume and texture of Gangjung drying at 40$\^{C}$ was better than other temperature conditions, regardless of drying methods. Quality of Gangjung, dried at single stage without aging, was superior to those dried at double stage including aging process. Moreover, single stage drying save the drying time at least 24 hr. Gangjung dried at high temperature became hard and less brittle in sensory evaluation. In image analysis, air cell distribution in inner structure of Gangjung became uniform and fine as drying temperature decreased to 40$\^{C}$. Overall, Gangjung made of Gangjung pellet by the use of far infrared ray drying at 40$\^{C}$ without aging, showed the best quality in terms of physical and sensory properties.

• Food Science and Preservation
• /
• v.14 no.1
• /
• pp.61-66
• /
• 2007

This study investigated changes in physicochemical properties of onion powders during various drying conditions. The moisture content during vacuum drying at $40^{\circ}C$ remained at 5.23% for 5 days of drying, and it was possible to quickly obtain day powder Weight reduction upon $-70^{\circ}C$ vacuum drying was 90% after 7 days. The large change in browning caused by vacuum freeze drying was lowest ($OD_{420}\;of\;1.173$) after 7 days of drying. The content of vitamin C increased with vacuum freeze drying. The major free sugars were fructose, glucose and sucrose. Of organic acids, citric acid was prominent and, after vacuum freeze drying, showed a high value of 1,965 mg/100g. Free amino acids noted were L-arginine, ${\beta}-alanine$, L-alanine and L-threonine. In summary, vacuum freeze drying at $-70^{\circ}C$ is optimal.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.187-192
• /
• 2000

The textile which is rotated in the tumbler dryer is dried by the heated air. the energy consumption for drying textile depends on various parameters. The objective of this study is to save the energy and the drying time. One of the various methods for energy saving is EGR(exhaust gas recirculation). We set the drying equipment for this study and perform the experimental study with the changes of the recirculation rate, the input power, and the air mass flow rate. We found the optimal drying conditions.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.4
• /
• pp.61-68
• /
• 2009

This paper presents the numerical analysis of process of sludge drying to know the characteristics of design parameters and develop the new process plant. Finite volume method and $k-{\varepsilon}$ turbulence model were used to analogy the sludge drying furnace. It has been attempted to perform the disposal of sewage sludge such as simple reclaiming and dumping in sea and incineration. Currently, these methods are restricted by national or international government regulations. The drying process is adopted as an effective method for sewage sludge treatment. However sewage sludge makes it difficult to treat with a large volume at the real drying process plant because of its own complicated physical, chemical, and thermal properties. The final design value of moisture content with 10% of the dried sludge can be obtained through the simulated outputs in this study.

• Restorative Dentistry and Endodontics
• /
• v.37 no.3
• /
• pp.155-159
• /
• 2012

Objectives: To investigate the effect of dentin moisture degree and air-drying time on dentin-bond strength of two different one-step self-etching adhesive systems. Materials and Methods: Twenty-four human third molars were used for microtensile bond strength testing of G-Bond and Clearfil $S^3$ Bond. The dentin surface was either blot-dried or air-dried before applying these adhesive agents. After application of the adhesive agent, three different air drying times were evaluated: 1, 5, and 10 sec. Composite resin was build up to 4 mm thickness and light cured for 40 sec with 2 separate layers. Then the tooth was sectioned and trimmed to measure the microtensile bond strength using a universal testing machine. The measured bond strengths were analyzed with three-way ANOVA and regression analysis was done (p = 0.05). Results: All three factors, materials, dentin wetness and air drying time, showed significant effect on the microtensile bond strength. Clearfil $S^3$ Bond, dry dentin surface and 10 sec air drying time showed higher bond strength. Conclusions: Within the limitation of this experiment, air drying time after the application of the one-step self-etching adhesive agent was the most significant factor affecting the bond strength, followed by the material difference and dentin moisture before applying the adhesive agent.