• Journal of Biosystems Engineering
• /
• 제31권5호
• /
• pp.416-422
• /
• 2006

Drying characteristics of green onion and onion during fluidized and fixed bed drying were investigated and compared. Sliced peen onion and onion were dried at drying air temperature of 45, 55, and $65^{\circ}C$. Drying air velocity during fluidized bed drying was adjusted with drying time at each drying temperature. Drying time to reach a given final moisture content was shorten in fluidized bed drying than in fixed bed drying - for drying temperature of 45, 55, and $65^{\circ}C$, the differences were 60, 60, and 50 min for green onion and 360, 180, and 60 min for onion. Drying constant (K) was greatly affected by drying method and drying temperature. Terminal velocity under fluidized bed drying was decreased exponentially for green onion and linearly (or onion with increase of drying temperature. Also, terminal velocity had linear relationship with moisture content for both green onion and onion.

• 펄프종이기술
• /
• 제43권5호
• /
• pp.17-26
• /
• 2011

Drying behavior and physical properties of HwBKP, SwBKP, and OCC handsheets depending on kneading, refining and wet pressing were analyzed. The maximum drying shrinkage velocity was newly adopted to verify the effect of mechanical treatment of pulps by evaluating drying behavior according to varying the kneading, refining and wet pressing treatments. Those various treatments were changed to evaluate the relationship between the maximum drying shrinkage velocity and handsheets properties. When the drying shrinkage and the maximum drying velocity increased by refining and wet-pressing, handsheets strength was increased. The maximum drying shrinkage velocity showed higher correlation with physical properties of paper than WRV at different refining loads at SwBKP and mixed pulp. At high wet-web dryness, drying shrinkage, the maximum drying shrinkage velocity and strength properties of handsheet were increased. It meant that drying shrinkage behavior was highly affected by not only fibers' shrinkage but also fiber bonding. Kneading pre-treatment for KOCC and SwBKP effectively modified fiber properties and increasing paper strength and drying shrinkage. The effect of kneading pre-treatment was also confirmed by the maximum drying shrinkage velocity. Strength properties of mixed pulp handsheets were not increased by the kneading pre-treatment, although the maximum drying shrinkage velocity and WRV was increased. It meant that fibers network bonding of HwBKP was limited because of ves sels and ray cells' interference for bonding. Therefore in order to improve paper strengths containing HwBKP by mechanical treatments, interference of vessels and ray cells for fiber bondings should be carefully controlled.

• 펄프종이기술
• /
• 제43권4호
• /
• pp.49-58
• /
• 2011

The maximum drying shrinkage velocity was proposed to verify bulk and stiffness improvement mechanism during drying according to papermaking parameters. It was based on the wet-web shrinkage behavior without the restraint of wet-web during drying, so intact drying impact could be measured. Bulking agent reduced the drying shrinkage and the maximum drying shrinkage velocity, so paper bulk increased and paper strength decreased. When adding cationic starch to stock with the bulking agent for strengthening, the bulk was increased further with additional decreasing of the drying shrinkage and the maximum drying shrinkage velocity. Paper strength also increased except tensile stiffness index with decreasing the drying shrinkage and the maximum drying shrinkage velocity. When using additional strength additives for strengthening of fiber interfaces extended by bulking agent and cationic starch, amphoteric strength additive increased paper stiffness without loss of paper bulk. It was considered that the added amphoteric strength additives were cross-linked to the stretched cationic starch and this cross-linking increased elasticity of fiber-polymer-fiber interfaces without changing the drying behavior. Paper bulk could be increased with decreasing the maximum drying shrinkage velocity. The drying shrinkage of paper also could be controlled by fiber-to-fiber bonding interfaces by the bulking agent. In this case, paper strength including stiffness was decreased by reducing fiber-to-fiber bonding but it could be improved by strengthening fiber-to-fiber interfaces with polymer complex without loss of bulk.

• Journal of Biosystems Engineering
• /
• 제32권1호
• /
• pp.6-12
• /
• 2007

This study was conducted to investigate the drying characteristics of oak mushroom using stationary far-infrared dryer. Drying characteristics was measured at drying air velocity 0.4 to 0.6 m/s and drying temperature 50, 60, and 70$^{\circ}C$, respectively. With high temperature of far-infrared heater and fast air velocity, the far-infrared drying rate of double air flow system was better than conventional heated-air drying as much as 39%. The value of color difference (E) of oak mushroom before and after drying was 8.95 by using heated air drying and was in the range of 3.76$\sim$6.98 by the far-infrared drying. The shrinkage rate of oak mushroom after heated air drying was higher than that of air velocity, 0.6 m/s of far-infrared drying conditions, and was lower than that of air velocity, 0.4 m/s of far-infrared drying conditions. The content of free amino acid was higher in far-infrared drying than heated air drying.

• Journal of Biosystems Engineering
• /
• 제40권1호
• /
• pp.61-66
• /
• 2015

Purpose: The purpose of this study was to establish conditions to dry a radish by examining the drying and quality characteristics depending on the air temperature and velocity of a far infrared conveyor dryer. Methods: A sample of weighing 6 kg was dried until the moisture content reached $15{\pm}0.5%$ (w.b.). Four temperatures (50, 60, 70, and $80^{\circ}C$) and three air velocity levels (0.4, 0.6, and 0.8 m/s) were employed as the drying factors. Results: The drying rate increased with the increase in the temperature and air velocity but decreased with time. However, the drying rate was influenced by temperature rather than velocity. At a temperature $50^{\circ}C$ with a air velocity of 0.4 m/s, it took 350 min for the radish to dry which was the longest drying time; $80^{\circ}C$ with a air velocity of 0.8m/s, it took 180 min for the radish to dry, which was the shortest drying time. ${\Delta}E$ (the color difference value) increased with the increase in temperature and air velocity. The browning and rehydration ratio increased as the temperature rose. Energy consumption decreased with the increased temperature and air velocity. Conclusions: Based on the results of this study, the best drying conditions for the radish were determined to be a temperature of $70^{\circ}C$ with an air velocity of 0.8 m/s.

• Journal of Biosystems Engineering
• /
• 제34권5호
• /
• pp.351-357
• /
• 2009

This study was conducted to verify the simulation model through the drying test, and investigate effect of factors, such as temperature of drying air, airflow rate, and velocity of the airflow, on the drying. The low temperature drying simulation model was developed based on the circulation dry simulation model presented by Keum et al. (1987), and by modifying low temperature thin layer drying model, equilibrium moisture content model, latent heat of vaporization model, and crack ratio prediction model. The heat pump and experimental dryer with a capacity of 150kg were used for the test. The RMSE between the predicted and measured value was 0.27% (drying temperature), 0.15% (crack ratio), and 2.08% (relative humidity), so the relevance of the model was verified. In addition, the effect of drying temperature, airflow rate, and velocity of the airflow on the drying was examined. The experimental results showed that the crack ratio at drying temperature of $25{\sim}40^{\circ}C$ was allowable. Moreover, at below $30^{\circ}C$, variation of the crack ratio was slight, but drying time was delayed. Given these results, the drying temperature of over $30^{\circ}C$ was effective. As the airflow rate increased, required energy dramatically increased. Whereas drying rate slowly increased, so loss of drying efficiency was caused. Considering these results, the dryer needed to be designed and adjusted to lower than $30\;m^3/min{\cdot}ton$. As velocity of the airflow increased, required drying energy increased when the velocity of the airflow was over $5\;m^3$/hr, while crack ratio and drying rate showed little variation.

• Journal of Biosystems Engineering
• /
• 제34권3호
• /
• pp.175-182
• /
• 2009

This study was conducted to investigate the drying characteristics of tissue cultured mountain ginseng roots. The far infrared rays dryer of a double blast system used for this experiment can control the drying parameters such as far infrared heater temperature and air velocity. The far infrared rays drying tests of tissue cultured mountain ginseng roots were performed at air velocity of 0.4, 0.6, 0.8 m/s, under drying air temperature of 50, 60, and $70^{circ}C$, respectively. The results were compared with one obtained by the heated air drying method. The drying characteristics such as drying rate, color, energy consumption, saponin components and antioxidant activities were analyzed. The results showed that the drying rate of far infrared rays drying was faster than that of heated air drying and due to high temperature of drying air and fast air velocity, the far infrared rays drying of double blast type was superior to the heated air drying. The value of the color difference for heated air drying was 10.11${\sim}$12.99 and that of far infrared rays drying was in the range of 7.05${\sim}$7.54, which was in the same drying condition, also energy consumption of far infrared rays drying was in the range of 3575${\sim}$6898 kJ/kg-water. At the same time, the antioxidant activities using far infrared rays drying were higher than those using heated air drying.

• 한국식품영양과학회지
• /
• 제20권5호
• /
• pp.503-508
• /
• 1991

영암어란의 제조방버은 건조기간이 긴 자연건조법으로 제조조건에 따라서 품질이 다르고 저장중 산화, 변색 및 단백질의 열화가 일어나 품질이 저하하였다. 본연구는 좋은 품질의 영암어란을 제조하기 위한 조건들의 확립을 위하여 품속에 따른 구성아미노산 함량과 산가, 과산화물가, TBA가의 변화로 최적풍속을 찾고 특성곡선을 구하였다. 엄장농도 5%, 바르는 참기름량은 3.0g/day에서 양호한 품질을 유지하기 위한 최적풍속으로 60% RH와 $20^{\circ}C$에서 2m/sec로 확정하였다. 영암어란의 제조에서 전통건조 방법의 건조기간은 20일이었으나 본 실험의 2m/sec 풍속에서 7일로 단축되었으며 이때의 건조특성곡선은 항율건조기가 없었고 감율건조기만 있었다.

• Journal of Biosystems Engineering
• /
• 제42권4호
• /
• pp.314-322
• /
• 2017

Purpose: This study was conducted to investigate the hot air drying characteristics of squash slices depending on the drying conditions (input air velocity, input air temperature, and sample thickness). Methods: The developed drying system was equipped with a controllable air blower and electric finned heater, drying chamber, and ventilation fan. Squash (summer squash called Korean zucchini) samples were cut into slices of two different thicknesses (5 and 10 mm). These were then dried at two different input air temperatures (60 and $70^{\circ}C$) and air velocities (5 and 7 m/s). Six well-known drying models were tested to describe the experimental drying data. A non-linear regression analysis was applied to determine model constants and statistical indices such as the coefficient of determination ($R^2$), reduced chi-square (${\chi}^2$), and root mean square error (RMSE). In addition, the effective moisture diffusivity ($D_{eff}$) was estimated based on the curve of ln(MR) versus drying time. Results: The results clearly showed that drying time decreased with an increase in input air temperature. Slice thickness also affected the drying time. Air velocity had a greater influence on drying time at $70^{\circ}C$ than at $60^{\circ}C$ for both thicknesses. All drying models accurately described the drying curve of squash slices regardless of slice thickness and drying conditions; the Modified Henderson and Pabis model had the best performance with the highest R2 and the lowest RMSE values. The effective moisture diffusivity ($D_{eff}$) changes, obtained from Fick's diffusion method, were between $1.67{\times}10^{-10}$ and $7.01{\times}10^{-10}m^2/s$. The moisture diffusivity was increased with an increase in input air temperature, velocity, and thickness. Conclusions: The drying time of squash slices varied depending on input temperature, velocity, and thickness of slices. The further study is necessary to figure out optimal drying condition for squash slices with retaining its original quality.

• Journal of Biosystems Engineering
• /
• 제37권5호
• /
• pp.327-334
• /
• 2012

Purpose: The color changes in red pepper during far infrared drying were studied in order to establish a color change model. Methods: The far infrared drying experiments of red pepper were conducted at two temperature levels of 60, $70^{\circ}C$ and two air velocity levels of 0.6 and 0.8 m/s. The results were compared with the hot-air drying method. The surface color changes parameters of red pepper were measured qualitatively based on L (lightness), a (redness), b (yellowness) and total color changes (${\Delta}E$). The goodness of fit of model was estimated using the coefficient of determination ($R^2$), the root mean square error (RMSE), the mean relative percent error (P) and the reduced chi-square (${\chi}^2$). Results: The results show that an increase in drying temperature and air velocity resulted in a decrease in drying time, the values of L (lightness) and a (redness) decreased with drying time during far infrared drying. The developed model showed higher $R^2$ values and lower RMSE, P and ${\chi}^2$ values. Conclusions: The model in this study could be beneficial to describe the color changes of red pepper by far infrared drying.