• Journal of the Korean Wood Science and Technology
• /
• v.52 no.1
• /
• pp.1-12
• /
• 2024

Betung bamboo (Dendrocalamus asper) is used as a building and handicraft material in Indonesia; however, bamboo needs to be dried to increase its stability. This study aimed to evaluate the efficiency of drying bamboo using solar energy and different drying oven designs. The betung bamboo pieces were dried using a direct solar dryer (direct drying) and an indirect solar dryer (indirect drying) and then the decrease in levels that occurred based on the relative humidity (RH) and temperature values achieved in the two dryers were compared. The highest average temperature in the direct indirect drying oven compartment was 60.1 ± 13.1℃ with 19.9 ± 16.4% RH and 60.2 ± 11.9℃ with 19.5 ± 15.5% RH, respectively. The drying defect in indirect drying was lower than that in direct drying, and indirect drying had a 61.7% greater average water loss than direct drying with significant difference (95%, analysis of variance) based on water loss/compartment volume parameters. Thus, the solar drying oven can be used to air-dry bamboo (14%) for 7 d from an initial moisture content of 70%-80% in bamboo strips. The results of this research can be used for small-scale bamboo processing industries that have limited use of electrical energy with quite good results.

• Journal of the Korean Wood Science and Technology
• /
• v.19 no.2
• /
• pp.72-76
• /
• 1991

• International Journal of Advanced Culture Technology
• /
• v.3 no.2
• /
• pp.138-143
• /
• 2015

This paper was aimed to study the drying kinetics of coffee and to investigate the thin-layer drying kinetics of coffee by using a convective air dryer. The coffee was dried for the temperatures of 40, 50 and $60^{\circ}C$ with relative humidity in the range of 14-25% the airflow rate fixed at 1 m/s. According to the experiment result, the drying rate curve showed that drying process took place only in the falling rate period. Seven thin layer drying models (Newton, Page, Henderson and Pabis, Logarithmic, Wang and Singh, Two terms, Modified Henderson and Pabis) were fitted to the experimental moisture content data. The Two-trem model was found to be a better model for describing the characteristics of coffee for the temperatures of 40, 50 and $60^{\circ}C$. The effective moisture diffusivity of coffee increased when the drying temperature increased. The value was in the range of $4.5028{\times}10^{-11}$ to $6.4803{\times}10^{-11}m^2/s$.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.44-48
• /
• 2021

Semiconductor inspection equipment makes components using materials with insulating properties for functional inspection including current and voltage of semiconductor parts. A representative insulating material is plastic, and plastic is made of a component through an injection process using plastic pellet. When plastic pellets contain excessive moisture, problems such as performance degradation and product surface defects occur. To prevent this, pre-drying is essential, and the heat convective type is the most applied. However, the heat convective type has a problem of low consumption efficiency and a long drying time. Recently, many studies have been conducted on a drying method using microwaves due to high energy efficiency. In this paper, drying was performed using a microwave for drying PC pellets. Energy consumption and drying efficiency analyzed by set up an experimental apparatus of heat convective, microwave, and hybrid(heat convective + microwave) types. It was confirmed that energy consumption and drying efficiency were high when drying using microwaves, and it was confirmed that the hybrid method improved drying performance compared to the heat convective method. It is expected that the research results of this paper can be used as basic data for drying plastic pellets using microwave.

• Journal of the Korean Wood Science and Technology
• /
• v.22 no.1
• /
• pp.66-71
• /
• 1994

To increase drying rate and reduce drying degradation, pretreatments such as prefreezing and presteaming have been widely used in wood industries. Presteaming lumbers prior to kiln drying is known positively to improve its permeability, to increase diffusion coefficient and to reduce discoloration, but negatively to increase collapse. Prefreezing lumbers prior to kiln drying is also known to reduce significantly its drying defects and its shrinkages. Thus it is no doubt that the pretreated lumbers shrink diversely from the untreated. In this study the shrinkage behaviors of the pretreated specimens are investigated by drying two tropical hardwoods (Apitong and Taun) in three different dying conditions: high temperature and slow drying rate (drying in a closed cylinder), high temperature and rapid drying rate (drying in an oven) and low temperature and slow drying rate(drying at room temperature). The prefrozen specimens show the least volumetric shrinkages in most drying conditions. The specimens dried in cylinders shrink most among all drying conditions. In general the pretreated specimens reached the 30 % moisture content faster than the untreated by about 30 %.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.379-384
• /
• 1994

In this paper, a fish-drying control method is proposed, which utilizes prediction of proper change in- weight of material fish based on skilled worker's performance. The function of the proposed system is largely broken down into two procedures: The procedure before drying and the one during drying. The procedure before drying is the determination of necessary drying conditions and the required drying time. Required drying time and proper changes in weight for a specific product are obtained by using fuzzy inference and regression models. The procedure during drying is the prediction of the state of material at the end of drying, or the state of product and regulation of drying conditions to attain the prescribed goal before drying. The prediction of product is obtained by using a set of linear-differential equations obtained by the authors' previous work. Drying conditions are regulated by using fuzzy inference. A good agreement between the results of simulation and experiments is obtained, which implies the usefulness of the present control method.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.22-28
• /
• 1997

This research was carried out to obtain the fundamental data for the development of the technology and practical use of far-infrared radiation(IR) drying of quarter-sliced decorative veneers of walnut and red oak. The average drying rates of IR drying were about one and half to four times those of kiln drying and this tendency was prominent in thin veneer. The end wavinesses of the IR-dried veneers were smaller than those of kiln-dried veneers. These were largely recovered by the cold treatments after drying. The consumed electric power for IR drying was about one-fifth to two-fifthes compared to that for kiln drying.

• 제어로봇시스템학회:학술대회논문집
• /
• 1993.10b
• /
• pp.132-137
• /
• 1993

In this paper, a fish drying process control system is proposed, which predicts the proper change with time in weight of the material fish and the drying conditions in advance, based on the performance of skilled worker. In order to implement a human expertise into an automated fish drying process control system, an experimental analysis is made and a model for the process is built. The proposed system divided into two procedures: The procedure before drying and the one during drying. The procedure before drying is for the prediction of necessary drying time. To estimate the necessary drying time, first, the proper change in weight for the product is obtained by using fuzzy reasoning. The condition part of the production rule consists of the factors of fish body and the expected degree of dryness. Kext, the necessary drying time is obtained by regression models. The variables employed in the models are the factors, inferred change in weight and drying conditions. The model for the procedure during drying is also proposed for more accurate estimation, which is described by a system of linear-differential equations.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.2
• /
• pp.139-146
• /
• 2017

This study was conducted to develop a new drying technology in order to quickly and massively dry bamboo tubes without crack and check. The bamboo tubes with the diameter of 45 mm - 68 mm had been impregnated in the solution of PEG-1000, and then were dried under room temperature and high temperature, respectively. The cracks occurred on all control specimens while no cracks were found on PEG treated specimens during drying at room temperature due to effect of PEG restraining the circumferential shrinkage of bamboo tube. But the drying period of this method was too long (200 days) compared to 10 hours of kiln drying. During fast high temperature drying, cracks occurred on all control specimens, but no cracks were found on PEG treated specimens, which could be accounted for more solidified PEG due to higher drying temperature and faster drying rate, and the tension set formed on the surface of bamboo tube in the early stage of drying owning to high drying temperature and low relative humidity. Thus, it is advised that PEG treated bamboo tube should be fast dried at high temperature in order to not only prevent crack or check in short drying period but also increase the dimensional stability of the products made of bamboo tubes.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.4
• /
• pp.51-60
• /
• 1997

We investigated the characteristics of air-and vacuum-drying heated by hot plates for 8~14cm-diameter logs or 6~12cm-thick pillars of Pinus koraiensis. And we evaluated the effects of longitudinal kerf and vacuum drying heated by hot plates. The vacuum drying times from green to 10.9~18.6% MC were 15 days, and these times were one-fifth compared to the air-drying times. The longitudinal kerfing had no significant, effect on drying rates during both air-drying and vacuum drying. But drying defects such as surface checks and V-shaped cracks were effectively prevented during air-drying and vacuum drying by longitudinal kerfing. The vacuum drying was more advantageous than air-drying for preventing of surface checks, end checks and V-shaped cracks, and especially, the vacuum dried pillars with longitudinal kerf were almost free from drying defects. In accelerated weathering conditions the resin did not exude for all specimens.