DOI QR코드

DOI QR Code

Drying Efficiency of Betung Bamboo Strips (Dendrocalamus asper) Based on Different Solar Drying Oven Designs

  • Ihak SUMARDI (School of Life Sciences and Technology, Institut Teknologi Bandung) ;
  • Anggit Kusuma Dewan DARU (School of Life Sciences and Technology, Institut Teknologi Bandung) ;
  • Alfi RUMIDATUL (School of Life Sciences and Technology, Institut Teknologi Bandung) ;
  • Rudi DUNGANI (School of Life Sciences and Technology, Institut Teknologi Bandung) ;
  • Yoyo SUHAYA (School of Life Sciences and Technology, Institut Teknologi Bandung) ;
  • Neil PRIHANTO (School of Life Sciences and Technology, Institut Teknologi Bandung) ;
  • Rudi HARTONO (Department of Forest Products, Faculty of Forestry, Universitas Sumatera Utara)
  • Received : 2023.08.18
  • Accepted : 2023.12.01
  • Published : 2024.01.25

Abstract

Betung bamboo (Dendrocalamus asper) is used as a building and handicraft material in Indonesia; however, bamboo needs to be dried to increase its stability. This study aimed to evaluate the efficiency of drying bamboo using solar energy and different drying oven designs. The betung bamboo pieces were dried using a direct solar dryer (direct drying) and an indirect solar dryer (indirect drying) and then the decrease in levels that occurred based on the relative humidity (RH) and temperature values achieved in the two dryers were compared. The highest average temperature in the direct indirect drying oven compartment was 60.1 ± 13.1℃ with 19.9 ± 16.4% RH and 60.2 ± 11.9℃ with 19.5 ± 15.5% RH, respectively. The drying defect in indirect drying was lower than that in direct drying, and indirect drying had a 61.7% greater average water loss than direct drying with significant difference (95%, analysis of variance) based on water loss/compartment volume parameters. Thus, the solar drying oven can be used to air-dry bamboo (14%) for 7 d from an initial moisture content of 70%-80% in bamboo strips. The results of this research can be used for small-scale bamboo processing industries that have limited use of electrical energy with quite good results.

Keywords

Acknowledgement

We thank the Institut Teknologi Bandung to provide financial support for the research by Research, Community Service and Innovation Program (P3MI-ITB 2022).

References

  1. Adil, Z., Sidabutar, H., Susilo, C., Justisia, A. 2014. A Study on Market Demand for Bamboo Products and Assessment of Bamboo Processing Technologies, ITTO PD 600/11 Rev. 1 (I): Model Capacity Building for Efficient and Sustainable Utilization of Bamboo Resources in Indonesia. Forest Industry Revitalization Body, Jakarta, Indonesia. 
  2. Aldabbagh, L.B.Y., Egelioglu, F., Ilkan, M. 2010. Single and double pass solar air heaters with wire mesh as packing bed. Energy 35(9): 3783-3787.  https://doi.org/10.1016/j.energy.2010.05.028
  3. Arinana, A., Rahman, M.M., Silaban, R.E.G., Himmi, S.K., Nandika, D. 2022. Preference of subterranean termites among community timber species in Bogor, Indonesia. Journal of the Korean Wood Science and Technology 50(6): 458-474.  https://doi.org/10.5658/WOOD.2022.50.6.458
  4. Banout, J., Ehl, P. 2010. Using a double-pass solar drier for drying of bamboo shoots. Journal of Agriculture and Rural Development in the Tropics and Subtropics 111(2): 119-127. 
  5. Basri, E., Pari, R. 2017. Sifat fisis dan pengeringan lima jenis bambu. Jurnal Penelitian Hasil Hutan 35(1): 1-13.  https://doi.org/10.20886/jphh.2017.35.1.1-13
  6. Bergman, T.L., Lavine, S.A., Incropera, F.P., Dewitt, D.P. 2011. Fundamentals of Heat and Mass Transfer. John Wiley & Sons, New York, NY, USA. 
  7. Chamoli, S., Chauhan, R., Thakur, N.S., Saini, J.S. 2012. A review of the performance of double pass solar air heater. Renewable and Sustainable Energy Reviews 16(1): 481-492.  https://doi.org/10.1016/j.rser.2011.08.012
  8. Chanpet, M., Rakmak, N., Matan, N., Siripatana, C. 2020. Effect of air velocity, temperature, and relative humidity on drying kinetics of rubberwood. Heliyon 6(10): E05151. 
  9. Darwis, A., Hadiyane, A., Sulistyawati, E., Sumardi, I. 2023. Effect of vascular bundles and fiber sheaths in nodes and internodes of Gigantochloa apus bamboo strips on tensile strength. Journal of the Korean Wood Science and Technology 51(4): 309-319.  https://doi.org/10.5658/WOOD.2023.51.4.309
  10. Dogra, S., Jilte, R.D., Sharma, A. 2020. Study of performance enhancement of single and double pass solar air heater with change in surface roughness. Journal of Physics: Conference Series 1531(1): 012091. 
  11. Fadwati, A.D., Hidayati, F., Na'iem, M. 2023. Evaluation of genetic parameters of growth characteristics and basic density of Eucalyptus pellita clones planted at two different sites in East Kalimantan, Indonesia. Journal of the Korean Wood Science and Technology 51(3): 222-237.  https://doi.org/10.5658/WOOD.2023.51.3.222
  12. Galih, N.M., Yang, S.M., Yu, S.M., Kang, S.G. 2020. Study on the mechanical properties of tropical hybrid cross laminated timber using bamboo laminated board as core layer. Journal of the Korean Wood Science and Technology 48(2): 245-252.  https://doi.org/10.5658/WOOD.2020.48.2.245
  13. Hong, C., Li, H., Xiong, Z., Lorenzo, R., Corbi, I., Corbi, O., Wei, D., Yuan, C., Yang, D., Zhang, H. 2020. Review of connections for engineered bamboo structures. Journal of Building Engineering 30: 101324. 
  14. Huang, P., Chang, W.S., Ansell, M.P., Chew, Y.M.J., Shea, A. 2015. Density distribution profile for internodes and nodes of Phyllostachys edulis (Moso bamboo) by computer tomography scanning. Construction and Building Materials 93: 197-204.  https://doi.org/10.1016/j.conbuildmat.2015.05.120
  15. Iswanto, A.H., Tarigan, F.O., Susilowati, A., Darwis, A., Fatriasari, W. 2021. Wood chemical compositions of Raru species originating from Central Tapanuli, North Sumatra, Indonesia: Effect of differences in wood species and log positions. Journal of the Korean Wood Science and Technology 49(5): 416-429.  https://doi.org/10.5658/WOOD.2021.49.5.416
  16. Kadivar, M., Gauss, C., Tomazello-Filho, M., Ahrar, A.J., Ghavami, K., Savastano, H., Jr. 2021. Optimization of thermo-mechanical densification of bamboo. Construction and Building Materials 298: 123860. 
  17. Kareem, M.W., Habib, K., Sulaiman, S.A. 2013. Comparative study of single pass collector and double pass solar collector filled with porous media. Asian Journal of Scientific Research 6(3): 445-455.  https://doi.org/10.3923/ajsr.2013.445.455
  18. Kareth, S.S., Petermann, M. 2014. Durability assessment and physical properties investigation of modified petung bamboo (Dendrocalamus asper) as resulted on acetylation, assisted by supercritical CO2. Procedia Chemistry 9: 273-283.  https://doi.org/10.1016/j.proche.2014.05.034
  19. Kaur, P.J., Kardam, V., Pant, K.K., Naik, S.N., Satya, S. 2016. Characterization of commercially important Asian bamboo species. European Journal of Wood and Wood Products 74(1): 137-139.  https://doi.org/10.1007/s00107-015-0977-y
  20. Khouya, A. 2022. Energy analysis of a combined solar wood drying system. Solar Energy 231: 270-282.  https://doi.org/10.1016/j.solener.2021.11.068
  21. Lee, H.W., Lee, E.J., Shin, Y.J., Jo, H.Y., Song, D.Y. 2023. Surface discoloration of ultraviolet (UV)-irradiated Phyllostachys bambusoides bamboo. Journal of the Korean Wood Science and Technology 51(3): 173-182.  https://doi.org/10.5658/WOOD.2023.51.3.173
  22. Liese, W. 2015. Bamboo: The Plant and Its Uses. Springer, Cham, Switzerland. 
  23. Lv, H.F., Ma, X.X., Zhang, B., Chen, X.F., Liu, X.M., Fang, C.H., Fei, B.H. 2019. Microwave-vacuum drying of round bamboo: A study of the physical properties. Construction and Building Materials 211: 44-51.  https://doi.org/10.1016/j.conbuildmat.2019.03.221
  24. Maulana, M.I., Murda, R.A., Purusatama, D.A., Sari, R.K., Nawawi, D.S., Nikmatin, S., Hidayat, W., Lee, S.H., Febrianto, F., Kim, N.H. 2021. Effect of alkali-washing at different concentration on the chemical compositions of the steam treated bamboo strands. Journal of the Korean Wood Science and Technology 49(1): 14-22.  https://doi.org/10.5658/WOOD.2021.49.1.14
  25. Maulana, S., Busyra, I., Fatrawana, A., Hidayat, W., Sari, R.K., Sumardi, I., Nyoman Jaya Wistara, I., Lee, S.H., Kim, N.H., Febrianto, F. 2017. Effects of steam treatment on physical and mechanical properties of bamboo oriented strand board. Journal of the Korean Wood Science and Technology 45(6): 872-882.  https://doi.org/10.5658/WOOD.2017.45.6.872
  26. Mijorski, S, Cammelli, S. 2016. Stack effect in high-rise buildings: A review. International Journal of High-Rise Buildings 5(4): 327-338.  https://doi.org/10.21022/IJHRB.2016.5.4.327
  27. Park, S.H., Jang, J.H., Wistara, N.J., Hidayat, W., Lee, M., Febrianto, F. 2018. Anatomical and physical properties of Indonesian bamboos carbonized at different temperatures. Journal of the Korean Wood Science and Technology 46(6): 656-669.  https://doi.org/10.5658/WOOD.2018.46.6.656
  28. Patra, T.K., Sheeba, K.N., Prakash P. 2013. Performance study on an indirect natural convention solar dryer for drying banana. eNREE 10(1): 3-11.
  29. Phonetip, K., Brodie, G., Ozarska, B., Belleville, B. 2018. Simulating solar kiln conditions. BioResources 13(2): 3740-3752.  https://doi.org/10.15376/biores.13.2.3740-3752
  30. Rusdiyantoro, Nurcahyanie, Y.D. 2016. Pengembangan mesin oven bamboo basket berbasis non toxic finish untuk mendukung strategi eco design produksi usaha kecil menengah. In: Yogyakarta, Indonesia, Seminar Nasional Teknik Industri Universitas Gadjah Mada 2016, pp. 21-26. 
  31. Sasongko, S.B., Hadiyanto, H., Djaeni, M., Perdanianti, A.M., Utari, F.D. 2020. Effects of drying temperature and relative humidity on the quality of dried onion slice. Heliyon 6(7): E04338. 
  32. Shu, B., Xiao, Z., Hong, L., Zhang, S., Li, C., Fu, N., Lu, X. 2020. Review on the application of bamboo-based materials in construction engineering. Journal of Renewable Materials 8(10): 1215-1242.  https://doi.org/10.32604/jrm.2020.011263
  33. Simo-Tagne, M., Zoulalian, A., Remond, R., Rogaume, Y. 2018. Mathematical modelling and numerical simulation of a simple solar dryer for tropical wood using a collector. Applied Thermal Engineering 131: 356-369.  https://doi.org/10.1016/j.applthermaleng.2017.12.014
  34. Sumardi, I., Alamsyah, E.M., Suhaya, Y., Dungani, R., Sulastiningsih, I.M., Pramestie, S.R. 2022. Development of bamboo zephyr composite and the physical and mechanical properties. Journal of the Korean Wood Science and Technology 50(2): 134-147.  https://doi.org/10.5658/WOOD.2022.50.2.134
  35. Tang, T.K.H., Welling, J., Liese, W. 2013. Kiln drying for bamboo culm parts of the species Bambusa stenostachya, Dendrocalamus asper and Thyrsostachys siamensis. Journal of the Indian Academy of Wood Science 10(1): 26-31.  https://doi.org/10.1007/s13196-013-0089-4
  36. Ugwu, S.N., Ugwuishiwu, B.O., Ekechukwu, O.V., Njoku, H., Ani, A.O. 2015. Design, construction, and evaluation of a mixed mode solar kiln with black-painted pebble bed for timber seasoning in a tropical setting. Renewable and Sustainable Energy Reviews 41: 1404-1412.  https://doi.org/10.1016/j.rser.2014.09.033
  37. Wulandari, F.T. 2019. Karateristik dan sifat fisik bambu petung (Dendrocalamus asper. backer) di kawasan hutan kemasyarakatan (HKM) Desa Aik Bual, Provinsi Nusa Tenggara Barat. Buletin LOUPE 15(01): 44-49.  https://doi.org/10.51967/buletinloupe.v15i01.27
  38. Xu, M., Cui, Z., Chen, Z., Xiang, J. 2017. Experimental study on compressive and tensile properties of a bamboo scrimber at elevated temperatures. Construction and Building Materials 151: 732-741.  https://doi.org/10.1016/j.conbuildmat.2017.06.128
  39. Xu, Q.F., Liang, C.F., Chen, J.H., Li, Y.C., Qin, H., Fuhrmann, J.J. 2020. Rapid bamboo invasion (expansion) and its effects on biodiversity and soil processes. Global Ecology and Conservation 21: e00787. 
  40. Yan, Y., Fei, B.H., Liu, S.Q. 2020. The relationship between moisture content and shrinkage strain in the process of bamboo air seasoning and cracking. Drying Technology 40(3): 571-580.  https://doi.org/10.1080/07373937.2020.1819307
  41. Yang, L., Liu, H. 2018. A review of eucalyptus wood collapse and its control during drying. BioResources 13(1): 2171-2181.  https://doi.org/10.15376/biores.13.1.Yang
  42. Zhang, Y.H., Huang, Y.X., Ma, H.X., Yu, W.J., Qi, Y. 2018. Effect of different pressing processes and density on dimensional stability and mechanical properties of bamboo fiber-based composites. Journal of the Korean Wood Science and Technology 46(4): 355-361.  https://doi.org/10.5658/WOOD.2018.46.4.355