• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.55-55
• /
• 1976

An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe?rature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.

• Journal of Biosystems Engineering
• /
• 제1권1호
• /
• pp.56-63
• /
• 1976

An experimental work was conducted to develop an optimum operating system of various hay drying systems ; sun-drying with long hay, sun-drying after chopping, sun-drying after crushing, heated air drying after chopping using batch-type dryer and heated air drying after crushing using tunnel-type dryer. Seombody having 60 cm long and initial moisture content of approximately 79 % in wet basis was used for the experiment. The criteria selected for determining the optimum operating condition were the drying performance rate, the production cost and quality of dried matter of each drying systems. The result of this study are summarized as follows : 1. Drying characteristics of leaves of long stem hay, chopped seombody and crushed one were obtained by maintaining the oven temperature at 70 degrees centigrade. The required drying times for various samples to approximately 15% moisture content in wet basis were about 50 min .for leaves ; 160 min. for crushed hay ; 250 min. for chopped hay ; 340min. for ling hay and more than 360 min .for stems. The drying time of crushed hay was required about 50 % of that for the uncrushed long hay. Such a significant difference of drying of time between the leaf and long stem may indicate that an effective drying of seombody may not be achieved unless any kind of special process treatment for the whole hay is undertaken. 2. In each individual drying system, the following conclusions were drawn: a. After 8 days sun-drying on concrete floor under good days with average tempe\ulcornerrature at $256{\circ}C$ and relative humidity at 55% at 2 P.M., the moisture content of long hay was still above 25 5'~ and the leaf loss during drying caused by wind and rough handling was more than 50 ~G. b. It was possible to dry the chopped seombody by sun-drying down to about 10 % moisture content within 5 days, however, a stock of heat and discolouration phenomena were observed during the drying, which may be due to the increased deposit-density by chopping, resulting in lowering the quality of the dried product. c. Sun-drying for the crushed material by hay-conditioner was required about 4 days to reduce the moisture content to about 10 %, keeping the quality of dried product at good grade. o. The optimum deposit-depth of the chopped seombody in the batch-type dryer used was about 28cm with about 42kg/hr of drying performance rate. However, it was necessary to overturn the materials between the upper and lower layers in order to obtain a good quality of dried product. d. The drying performance rate by the tunnel-type drier was highest among those of drying systems tested, giving the rate of approximately 400kg/day. 3. On reviewing the individual drying system for seombody, it was possible to draw conclusion that the best system was tunnel drying with the crushed seombody as far as the performance rate was concerned. However, the methods gives the highest operational cost. The system for the lowest operational cost with good quality of dried product was the sun-drying with the crushed material. Accordingly, it may be recommended that the system of sun-drying for the crushed seombody may be the most feasible system presently applicable to farm-level operation.

• 한국식품과학회지
• /
• 제25권5호
• /
• pp.558-564
• /
• 1993

쌀보리를 시료로 하여 건조조건을 다르게 하여 유동층 건조특성에 영향을 미치는 외부요인에 대해서 조사한 결과를 요약하면 다음과 같다. 쌀보리의 유동층건조는 항률건조기가 없이 감률건조 1단계, 감률건조 2단계의 두 단계로 일어남을 알 수 있었다. 또한 건조속도상수는 충전량이 적을수록, 공기속도가 클수록, 공기온도가 높을수록, 상대습도가 낮을수록 켰으며, 감율건조단계에서의 건조속도상수는 Arrhenius형의 plot에서 좋은 직선관계를 나타내어 이 단계가 활성화 과정임을 알 수 있으며, 감률건조 제 1단계의 활성화 에너지는 1900ca1/gmol, 감률건조 제 2단계의 활성화 에너지는 2500ca1/gmol을 각각 나타내었다.

• 한국건축시공학회지
• /
• 제4권4호
• /
• pp.71-77
• /
• 2004

Drying Shrinkage has much complexity as it has relations with both internal elements of concrete and external factors. Therefore, experiments on Concrete Drying Shrinkage are carried out in this study under simplified circumstances applying temperature & Humidity test chamber which enables constant temperature and humidity. Comparative analyses have been made respectively according to the consequences aiming at modelling for prediction of Concrete Drying Shrinkage and making out measures to reduce it. Strain Rate of Drying Shrinkage of concrete under the condition of dry air appears to rise by about 20%-30% in proportion as the temperature rises $5^{\circ}C$ when the humidity was held below 10% compared under the condition of dry temperature & Humidity test chamber. Strain Rate of Drying Shrinkage in pit sand concrete increased 20% higher than measured when in river sand under the condition of 90-day material age. A general formula with two variables is derived as follow ${\varepsilon}={\alpha}_1＋{\beta}_1x_1＋{\beta}_2x_2＋{\beta}_3x_1^2＋{\beta}_5x_2^2$. and also graphed in 3 dimensions, enabling to apply to actual design and predict Strain Rate of Drying Shrinkage in concrete. The results of prediction of Rate of Drying Shrinkage by Response Surface Analysis are as follows. The coefficient of correlation of Drying Shrinkage in Concrete was over 90%.

• Journal of Biosystems Engineering
• /
• 제34권5호
• /
• pp.358-362
• /
• 2009

This study was conducted to evaluate the performance of a 12 tons capacity circulating concurrent flow rice dryer. An actual scale dryer with the capacity of 12 tons was developed to obtain a faster drying rate of 0.8~1.2%(w.b.)/h, while maintaining a lower drying energy consumption of 5,000 kJ/kg-water and achieving a drying quality that was comparable to a conventional cross-flow rice dryer. The Test-1 was conducted at $110^{\circ}C\;-\;20\;cmm/m^2$ and the Test-2 was conducted at $120-110-100-90^{\circ}C\;-\;20\;cmm/m^2$ under the same conditions as Test-1. In Test-1, the drying rate, drying energy consumption and crack ratio were 0.98 %(w.b.)/h, 4,573 kJ/kg-water and 3.2%, respectively. In Test-2, the drying rate, drying energy consumption and crack ratio were 0.74 %(w.b.)/h, 4,790 kJ/kg-water and 4.0%, respectively. The results of these tests demonstrated that this concurrent-flow dryer reached the desired drying rate, drying energy consumption and crack ratio.

• 한국건축시공학회지
• /
• 제6권1호
• /
• pp.73-77
• /
• 2006

Drying Shrinkage has much complexity as it has relations with both internal elements of concrete and external factors. Therefore, experiments on Concrete Drying Shrinkage are carried out in this study under simplified circumstances applying temperature & Humidity test chamber which enables constant temperature and humidify. Comparative analyses have been made respectively according to the consequences aiming at modelling for prediction of Concrete Drying Shrinkage and making out measures to reduce it. As a result Strain Rate of Drying Shrinkage of concrete was measured to increase by average $10{\times}10^{-5}$ in proportion to additional 4% increase in fine aggregate ratio, when water/cement ratio constant. Strain Rate of Drying Shrinkage in pit sand concrete increased 20% higher than measured when in river sand under the condition of 90-day material age. 6. Strain Rate of Drying Shrinkage in sea sand concrete increased $10%{\sim}15%$ higher than measured when in river sand. The results of prediction of Rate of Drying Shrinkage by Response Surface Analysis are as fellows. The coefficient of correlation of Drying Shrinkage in concrete was over 90%.

• Journal of Advanced Marine Engineering and Technology
• /
• 제25권3호
• /
• pp.588-594
• /
• 2001

The aim of this paper is to develop the low temperature vacuum dryer, with low initial investments and operating costs, easy operating method and trouble-free operation Usally operations just below atmospheric pressure, as with direct dryers, but some are built for vacuum operation with pressure as low 50 mmHg abs. The lowers the boiling point to $39^{\circ}C$ The experimental data of quantitative analysis for using practically were obtained by the constant drying rate period and reducing drying rate period according to the temperature of hot water which is the experimental parameters of present experiment. As the results, it took about 20 hours for material to reach about 18% of the final moisture content is order to store products for a long time about 450% of the early moisture content at the beginning of drying and maximum drying rate comes to about 0.30 kg/m2hr at about 350% of the moisture content.

• 한국연초학회지
• /
• 제17권2호
• /
• pp.149-159
• /
• 1995

The freeze drying rate was investigated under various conditions such as pressure and moisture contents in order to establish the optimum condition for expansion of the culled flue cured tobacco lamina. The optimal pressure in the chamber to maintain the heat and mass transfer was about 0.8torr, When the moisture contents of sample was 50-60%, expanding rate was the optimum condition and the rate was 67-76%. As the thickness of the sample layers was increased, drying-rate was decreased conversely and this result seemed to be due to decline of heat and mass transfer coefficients. Differences with the position of its stalk were also observed in drying rate, and low stalk position leaves of 5 and 3 was the fastest. Key words : freeze drying, Popping, expansion tobacco.

• Journal of Biosystems Engineering
• /
• 제41권3호
• /
• pp.232-239
• /
• 2016

Purpose: The aims of this study were to define the drying characteristics of rapeseed and to determine the optimum thin-layer drying model for rapeseed by considering the effects of drying temperature and relative humidity. Methods: The thin-layer drying experiments were conducted at different combinations of drying air temperature levels of 40, 50, and $60^{\circ}C$ and relative humidity levels of 30, 45, and 60%, on both of which drying rate depends. The drying rate increased with increasing air temperature as well as decreasing relative humidity. The 13 models were fitted to the experimental data. Results: From the results of the regression analysis for empirical constants of the Page model, the values of $R^2$ were the highest (ranging from 0.9924 to 0.9966) and the values of RMSE were the lowest (ranging from 0.0169 to 0.0296). Conclusions: For all drying conditions considered, the Page model was determined to be the most suitable model for describing the thin-layer drying of rapeseed (P-value < 0.01). The moisture diffusion coefficients were calculated using the moisture diffusion equation for a spherical shape, based on Fick's second law.

• 한국식품영양과학회지
• /
• 제25권3호
• /
• pp.453-459
• /
• 1996

This study was carried out to determine the changes in quality during the drying process and the optimum drying condition for utilizing soybean curd residue. The quality criteria for soybean curd residue were acid value, peroxide value, fatty acid composition and microbial concentration. The acid values of soybean curd residue were 7.5, 4.5 and 5.9 KOH mg/g upon 12 hour drying with open-air sun, ambient-air blast and warm-air blast, respectively. The numbers of total aerobic bacteria and molds increased remarkably during drying with open-air sunlight, ambient-air blast and warm-air blast except for hot air blast. Among different drying methods, the hot air blast drying(1kg of sample) was the most effective methods, which completed in three hours. Also, the drying method demonstrated a typical drying curve ; settling down, constant rate drying and falling rate drying period were shown within one hour, from one and three hours and after three hours, respectively. Moreover, there was significant variation in the constant drying period for the quality of soybean curd residue.