• Journal of Biosystems Engineering
• /
• 제41권4호
• /
• pp.342-356
• /
• 2016

Purpose: The drying of a thin layer of native cassava starch in a tray dryer was modeled to establish an equation for predicting the drying behavior under given conditions. Methods: Drying tests were performed using samples of native cassava starch over a temperature range of $40-60^{\circ}C$. We investigated the variation in the drying time, dynamic equilibrium moisture content, drying rate period, critical moisture content, and effective diffusivity of the starch with temperature. The starch diffusion coefficient and drying activation energy were determined. A modification of the model developed by Hii et al. was devised and tested alongside fourteen other models. Results: For starch with an initial moisture content of 82% (db), the drying time and dynamic equilibrium moisture content decreased as the temperature increased. The constant drying rate phase preceded the falling rate phase between $40-55^{\circ}C$. Drying at $60^{\circ}C$ occurred only in the falling rate phase. The critical moisture content was observed in the $40-55^{\circ}C$ range and increased with the temperature. The effective diffusivity of the starch increased as the drying temperature increased from 40 to $60^{\circ}C$. The modified Hii et al. model produced randomized residual plots, the highest $R^2$, and the lowest standard error of estimates. Conclusions: Drying time decreased linearly with an increase in the temperature, while the decrease in the moisture content was linear between $40-55^{\circ}C$. The constant drying rate phase occurred without any period of induction over a temperature range of $40-55^{\circ}C$ prior to the falling rate period, while drying at $60^{\circ}C$ took place only in the falling rate phase. The effective diffusivity had an Arrhenius relationship with the temperature. The modified Hii et al. model proved to be optimum for predicting the drying behavior of the starch in the tray dryer.

• Journal of Biosystems Engineering
• /
• 제34권1호
• /
• pp.30-36
• /
• 2009

This study was performed to determine the effect of drying conditions on the germination properties of rapeseed after seeds were dried under different drying conditions: $40^{\circ}C$, $50^{\circ}C$, or $60^{\circ}C$ in combination with 30%, 45%, or 60% relative humidity. As analytic results, drying conditions had significant effects (P-value < 0.001) and drying temperature was considered as the main factor on the germination properties of rapeseed. When drying temperature increased or relative humidity decreased, the vigor rate and germination rate decreased, the median germination time increased. The maximum values of vigor rate and germination rate were 90% and 95.44%, and their minimum values were 60.17 and 75%, respectively. To ensure the standard germination rate of 85%. The appropriate drying zone was determined and the drying temperature should be less than $51.0^{\circ}C$, $54.5^{\circ}C$ and $58.7^{\circ}C$ at 30%, 45% and 60% RH, respectively. The values for median germination time varied from 2 to 4 days. The predicted models of germination rate, vigor rate, and median germination time were determined.

• 한국수산과학회지
• /
• 제15권1호
• /
• pp.107-110
• /
• 1982

Fixed bed drying method was selected to reduce the initial drying time of squid and the effects of drying air temperature and bed height on the drying rate were investigated, with following results. 1. The drying rate in the fixed bed dryer was faster than that of natural convection type dryer heated indirectly and that of hot air dryer heated directly. 2, Shirai-equation was applicable to squid being dried. Using the equation, drying rate constant obtained was as shown in table 1.

• Journal of the Korean Wood Science and Technology
• /
• 제20권1호
• /
• pp.5-14
• /
• 1992

Experimental external collector type solar lumber dryer of $1m^3$ of maximum capacity with $1.6m^3$ of collector area was designed and constructed. The seasonal performance of solar dryer, including air-conditions, energy efficiency, and drying characteristics of 3cm-thick red pine and douglas-fir lumber was investigated. Also, the economic analysis was carried out. Annual average solar drying rate was about 2 times faster than air-drying rate with no significant difference in the amount of drying defects. But in initial drying stage air-drying rate in winter was much faster and those in spring and autumn were slightly slower than solar drying rate in each season. Annual average energy efficiency of solar-dryer and-collector was 25% and 57%, respectively. Fuel savings were over 50% at 15% of energy inflation rate and the payback period was estimated as 6.10 years at 30% of energy inflation rate.

• Journal of the Korean Wood Science and Technology
• /
• 제18권1호
• /
• pp.39-51
• /
• 1990

This research was carried out to offer the basis data for development of optimum drying schedule for a domestic oak species (Quercus grosseserrata B1.) by investigating drying rate. stress, defect, and moisuture gradient with board thicknesses and drying schedules (code number T4-C2 and T3-B1). The results were obtained as follows: 1. Average drying rate and total drying time from 52.2% to 5.8% were 0.105%/hr and 486 hours for drying schedule T4-C2 and those from 62.1% to 8.3% were 0.070%/hr. and 811 hours for drying schedule T3-B1. 2. Drying rates for 28mm- and 31mm-thick boards showed similar tendency, but were significantly different from 25mm- thick board in drying schedule T4-C2 and those for 22mm-, 25mm- 28mm- and 31mm-thick boards showed similar tendency but were significantly different from 19mm- thick boards in drying schedule T3-B1. 3. The moisture gradients for drying schedule T4-C2 were steeper than those for drying schedule T3-B1 during drying period. and especially in early drying stage slow slope of moisture gradients of drying schedule T3-B1 was effective in preventing serious problem of surface checks. 4. Drying stresses were lower in drying schedule T3-B1 than in drying schedule T4-C2 during drying period. 5. Drying schedule T4-C2 was appropriate for 25mm-thick board but not for 28mm- and 31mm-thick board because of strong drying condition. Drying schedule T3-B1 was appropriate for 28mm- and 31 mm-thick board but not for 19mm-, 22mm-, and 25mm-thick board because of weak drying condition.

• 분석과학
• /
• 제10권6호
• /
• pp.418-426
• /
• 1997

고주파를 이용한 오니의 건조특성에 대하여 살펴보고 재래식 건조특성과 비교 분석하였다. 고주파 건조는 빠른 속도와 높은 효율을 보였다. 재래식 건조에서는 항율건조기간이 나타나지 않았고 수분은 모세관현상에 의하여 이동하였다. 오니의 수분 중 자유수와 결합수는 존재하지 않았다. 고주파 건조에서 감율건조기간이 두 부분으로 나타났으며, 수분의 이동은 확산에 의하여 일어났다. 증발 표면적이 커질수록 수분의 제거가 촉진되었고, 오니의 지름이 커질수록 넓은 범위의 항율건조 기간이 나타났으며, 모양에 따라서도 건조특성이 다르게 나타났다. 고주파 건조에서는 오니의 중심부에서 가장 먼저 온도가 상승하였으며, 항율건조기간에서 $80{\sim}100^{\circ}C$로 일정하게 유지되면서 가장 높았다.

• 한국축산식품학회지
• /
• 제18권2호
• /
• pp.164-175
• /
• 1998

The objective of this study was to investigate the effects of freezing rate on ice crystal size and freeze-drying rate. Our experiments were carried out with self-manufactured freeze-dryer. Gelatin gels (2% w / w, 80$\times$20mm) were frozen unidirectionally (Neumann's model) from the bottom at -45, -30, -20, and -15$^{\circ}C$ and followed with freeze-drying. Under the upper conditions we measured freezing rate and the change of temperature and pressure during freeze drying. Freeze-dried gelatins were cut horizontally into 5 mm thickness from the bottom and measured their pore sizes. Also freeze-drying rate(primary drying) is estimated by measuring the temperature of sample and pressure of vacuum chamber. During freeze-drying, profiles of pressure and temperature were shown constant tendency regardless of freezing temperature and we could expect the end-point of freeze drying by considering pressure and temperature together. In temperature profiles, the point which temperature increased significantly was observed during freeze-drying. There is no relationship between freeze temperature and drying rate of primary drying in our model system. As freezing temperature increased, ice crystal size(X*) which correspond to 63.2% of cumulative frequency was increased and at the same freezing temperature ice crystal size(X*) was decreased with distance from the bottom of the sample. Freezing conditions have a strong influence on the quality of the final freeze-dried products in freeze-drying system.

• Food Science and Biotechnology
• /
• 제18권1호
• /
• pp.202-206
• /
• 2009

Drying characteristics of fresh Korean-type rehmannia (jiwhang) noodle was investigated to determine drying kinetic parameters under the experimental conditions of 5 temperatures (30, 40, 60, 80, and $90^{\circ}C$). Drying curve of the noodle showed a biphasic pattern of decrease in drying rate with initial rapid drying followed by slow dehydration as the progress in drying. In all drying conditions, only falling drying rate period was observed and the drying rate of the noodle was greatly influenced by the drying temperature. The effective diffusion coefficients ($D_{eff}$) were determined by the diffusion model and their temperature dependency was determined using an Arrhenius equation. The activation energy ($E_a$) values for the drying of the noodle were 19.94 and 21.09 kJ/mol at the initial and the latter stage of dehydration, which were comparable to those of pasta or Japanese udong dehydration.

• 대한기계학회논문집B
• /
• 제31권10호
• /
• pp.860-867
• /
• 2007

Heat pump drying has a great potential for energy saving due to its high energy efficiency in comparison with conventional air drying. In the present study, the performance simulation for the basic design of a heat pump dryer has been carried out. The simulation includes one-stage heat pump cycle, simple drying process using the drying efficiency. As an example, the heat pump cycle with Refrigerant 134a has been investigated. For the operating conditions such as the average temperature of the condenser, the heat rate released in the condenser, the flow rate of drying air, and drying efficiency, the simulation has been carried out to figure out the performance of the dryer. The parameters considered in the design of the dryer are COP, MER, SMER, the rate of dehumidification, the temperature and humidity of drying air and those parameters are compared for different conditions after carrying out the simulation.

• 동력기계공학회지
• /
• 제15권3호
• /
• pp.46-51
• /
• 2011

Low temperature vacuum drying technique, whose drying time and quantity of exhausting energy is about 25~30% of hot air drying, is very excellent in the drying efficiency. This paper is made out in the aspects of heat engineering with the object of developing Korean drying machine which can dry once a large quantity of objects to be dried in the state of low temperature and vacuum. As the results, it took about 17 hours(3~4 days in case of hot air drying) for material to reach about 18% of the final moisture content in order to store products for a long time, from about 78~80% of the early moisture content at the beginning of drying, and maximum drying rate comes to about 0.35 kg/m2hr at about 400% of the moisture content.