• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.1128-1133
• /
• 2008

Drying process in the thin film layer of sludge with the thickness less than a few millimeters has been investigated using the simple one-dimensional model. Thin film drying is usually used to dry the viscous materials like sewage sludge. The thin film layer of sludge is dried on the metallic surface through which thermal energy is supplied to the layer during drying. In order to solve the equations, the mass transfer rate on the drying surface should be determined. The mass flux of evaporated water vapor on the surface is estimated with the formulation given in the literature. The effect of heating temperature, film thickness, and air velocity on drying has been examined to figure out the drying characteristics of the sludge layer.

• Journal of Biosystems Engineering
• /
• v.19 no.2
• /
• pp.112-123
• /
• 1994

At present, no appropriate drying conditions can be found for the heated-air drying of mushroom in Korea. Usually, mushroom is being dried at the temperature range of 40 to $50^{\circ}C$ until the moisture content reaches 10~13% (wb). However, drying characteristics of the mushroom should be investigated for quality improvement and efficient drying operation of the mushroom. The results of this study may be summarized as follows ; 1. The effect of air temperature on the rate of drying was greater than that of relative humidity for drying of mushroom, and the rate of drying was increased with increase in the air temperature. 2. Drying rate for Shiitake mushroom showed falling-rate period of drying without constant-rate period of drying. Drying rate for Oyster mushroom showed a short constant-rate period at the initial stage of drying process, and followed by falling-rate period of drying. 3. Exponential and App.-Diffusion models were found to describe well the drying process of Shiitake mushroom. Exponential and Thompson models for Oyster mushroom in which Thompson model was the most suitable for Oyster mushroom. 4. The equilibrium moisture content of the mushroom decreased with decrease in the air temperature and increase in the relative humidity. In room condition($20^{\circ}C$, 54% RH), the calculated values of the equilibrium moisture content showed 11.17% for Shiitake mushroom and 13.19% for Oyster mushroom, respectively.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.12
• /
• pp.25-34
• /
• 2013

This paper presents the results of a reduced-scale physical model investigation into the behavior of retaining walls subject to cycles of wetting and drying due to rainfall infiltration. Reduced-scale model walls equipped with a water spraying system that can simulate the wetting process were first constructed and a series of tests were conducted with due consideration of different rainfall intensities and backfill soil types. The results indicate that cycles of wetting and drying process have adverse effects on the wall behavior, increasing wall deformation as well as earth pressure acting on the wall, and that the first cycle of wetting and drying process has more pronounced effect on the wall performance than the ensuing cycles. It is also shown that the degree to which the wetting and drying cycles affect the wall behavior depends greatly on the backfill soil type, and that the larger the fine contents, the greater is the effect of cycles of wetting and drying on the wall behavior. Practical implications of the findings from this study are discussed in great detail.

• Journal of environmental and Sanitary engineering
• /
• v.13 no.1
• /
• pp.9-15
• /
• 1998

Microwave heating and drying processes have been well established in various industrial applications. Feasibilities of successful application of microwave drying to many material have been shown on the laboratory or pilot-plant scale. The microwave drying behavior of plating sludge are considered in this paper. The plating sludge containing 70%, 80% and 90% water exposed to microwave power at 2,450 MHz, 700W. An experimental microwave drying apparatus was designed and constructed to monitor weight loss during drying. By studying the drying characteristic curve, the moisture in sludge was almost classified into two categories : free moisture and intestinal moisture. And the critical moisture contents at which the drying rate ceases to be constant were from 10.1 to 10.5%. A simple drying model is proposed which may be used to describe drying behavior of plating sludge. The constant rate and the falling rate periods in microwave drying were addressed separately. From the eqation of constant rate period the drying rate constants decreased exponentially with increasing depth. Microwave heating compared with conventional heating offered higher heating rates from 9 to 16 times. Therefore, microwave drying process can be effective in removing moisture from plating sludge.

• Journal of Biosystems Engineering
• /
• v.11 no.2
• /
• pp.66-75
• /
• 1986

In order to improve the traditional post harvest system in Korea, a model for mechanized grain drying and storage facilities was developed. Also, a computer program for the model system was developed. For the study, flat type steel bin and circulation type dryer were selected for the model and Fortran language was used for the computer program. This program was tested by using various practical data. The following results were obtained from the study: 1. The general model developed can be used for designing a rough rice drying and storage facility within the range from 100 ton to 1000 ton capacity. 2. Major output of the computer program for designing a model system were as follow; a. The dimension of the plant. b. The storage bin size, dryer number and dryer size. c. The dimension of individual equipment and its required HP. d. Capital requirement and operating cost of the model system.

• The Korean Journal of Food And Nutrition
• /
• v.35 no.6
• /
• pp.426-434
• /
• 2022

In this study, the effect of osmotic drying conditions of mangoes on hot air drying was investigated. Four different osmotic agents of 60 Brix, such as S60, SM10, HF80, and SG25, were prepared. Mango slabs were osmotically dried with the agents at a ratio of 1:4 (w/w) for up to 8 hours. SG25 showed the lowest weight reduction and moisture loss during the process. As a result of hot-air drying, all samples showed a high correlation with the Page model (0.9761~0.9997), and the required drying time of all samples that were osmotically dried was reduced compared to the non-osmotically dried group. After hot-air drying, the pH value increased according to the drying temperature. The L, a, and b values and the total polyphenol content also decreased. Through this study, the possibility of osmotic drying was confirmed to increase the efficiency of hot air drying of mangoes, which is expected to contribute to the industrial use of domestic mangoes.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2009.05a
• /
• pp.407-408
• /
• 2009

Drying shrinkage have influence on the durability of concrete structure. Various models have been suggested to predict the drying shrinkage, experimentally. In this study, the drying shrinkage with Concrete strength and Curing condition was measured, and compared with representative model code. As a result, drying shrinkage was reduced as W/C ratio decrease, and total shrinkage greatly reduced in 4 week wet curing case. The test results agreed with EC2 model better than the other.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2003.11a
• /
• pp.272-290
• /
• 2003

In this study a model for the drying process in paper production plants was developed based on the mass and heat balances around drying cycles. Relationships for the heat transfer coefficients between the web and the air as well as between the drying cylinder and the web were extracted from the closed-loop plant operation data. It was found that the heat transfer coefficients could be represented effectively in terms of moisture content, basis weight and reel velocity. The effectiveness of the proposed model was illustrated through numerical simulations. From the comparison with the operation data, the proposed model represents the paper plant being considered with sufficient accuracy.

• Korean Journal of Food Science and Technology
• /
• v.25 no.4
• /
• pp.313-320
• /
• 1993

A sublimation model of the freeze drying process, which accounted for the removal of free water, was presented and used to study the operation conditions of freeze driers for carrot juice. It was found that the shortest drying time was obtained when the condenser temperature and chamber pressure were kept at heir lowest values and the plate temperature was controlled independently so that the scorch and melting constraints were both held throughout the drying period. The effect of sample thickness on the drying time was significant. Optimal policies were investigated experimentally in laboratory freeze dryer.

• Journal of Biosystems Engineering
• /
• v.27 no.3
• /
• pp.219-226
• /
• 2002

Desorption equilibrium moisture contents of oak mushroom were measured by the static method using salt solutions at flour temperature levels of 35$\^{C}$, 45$\^{C}$, 55$\^{C}$ and 6$\^{C}$ and five relative humidity levels in the range from 11.0% to 90.8%. EMC data were fitted to the modified Henderson, Chung-Pfost, modified Halsey and modified Oswin models using nonlinear regression analysis. Drying tests far oak mushroom were conducted in an experimental dryer equipped with air conditioning unit. The drying test were performed in triplicate at flour air temperatures of 35$\^{C}$, 45$\^{C}$, 55$\^{C}$ and 65$\^{C}$ and three relative humidities of 30%, 50% and 70% respectively. Measured moisture ratio data were fitted to the selected four drying models(Lewis, Page, simplified diffusion and Thompson models) using stepwise multiple regression analysis. The results of comparing root mean square errors for EMC models showed that modified Halsey was the best model, and modified Oswin models could be available far oak mushroom. The results of comparing coefficients of determination and root mean square errors of moisture ratio for four drying models showed that Page model were found to fit adequately to all drying test data with a coefficient of determination of 0.9990 and root mean square error of moisture ratio of 0.00739.